That makes sense. I get it now. So bottom line there is no way to extend
the mag release on a Glock 17 9mm and stay in SSP.
Thanks Again
On Mon, Jun 11, 2018 at 4:15 PM Wade Price <wade.price@xxxxxxx> wrote:
Since that part (8794) does not appear to be installed in any
off-the-shelf gun they sell, it does not appear to be SSP legal.
On Jun 11, 2018, at 4:11 PM, Sean Murphy <murf.sean@xxxxxxxxx> wrote:release. They will not sell to anyone. Only to a certified Glock Armorer.
No, it is the recommended part for the 17 9mm Gen5 for an extended mag
gen5.
On Mon, Jun 11, 2018 at 3:59 PM Wade Price <wade.price@xxxxxxx> wrote:
Did they say that is the part installed at the factory?
On Jun 11, 2018, at 3:42 PM, Sean Murphy <murf.sean@xxxxxxxxx> wrote:
I was told by Glock today that (8794) is the extended release for a 17
same MFG., But used as standard release on other models.
I would think that I would still be so since it is a snap in part,
the standard part on the Gen 3 G34/35.
Do have this right?
Sean
On Mon, Jun 11, 2018, 3:30 PM Wade Price <wade.price@xxxxxxx> wrote:
IDPA:
The Glock extended mag release for small frame Gen 3 Glocks (1981) is
(8794) is NOT the standard part on the Gen 4 G34/35.However, the Glock extended mag release for small frame Gen 4 Glocks
Gen 3 appears to be legal in SSP. However the Gen 4 extended mag release
So, according to rule 8.2.1.2-C, the Glock extended mag release for
does not appear to be.
https://www.brownells.com/handgun-parts/frame-parts/magazine-release-parts/magazine-releases/extended-magazine-release-prod22998.aspx
https://www.brownells.com/handgun-parts/frame-parts/magazine-release-parts/magazine-releases/magazine-catch-reversible-extended-0-75-fits-gen4-sku100700094-69854-150579.aspx?sku=100-700-094
G34/35.
The same applies to Glock extended slide stops:
The Glock extended slide stop is standard on both Gen 3 and Gen 4
https://www.brownells.com/handgun-parts/frame-parts/slide-catch-parts/slide-catches/extended-slide-stop-levers-prod23432.aspx
gun would be bumped into ESP.
If you install a non-compliant mag release and/or slide stop, then the
hammers, and triggers, that are stock on one SSP legal firearm may be used
"IDPA 8.2.1.2 - SSP Permitted Modifications (Inclusive list):
C. Magazine releases, slide stops, safety levers, de-cocking levers,
on another SSP legal firearm from the same manufacturer provided they are
drop in replacements. Parts in this list must come factory installed on
standard production firearms. Special parts that are available installed
only from a factory custom shop are not eligible in SSP."
divisions. However, effective in 2018, Production and Carry Optics guns may
USPSA:
USPSA had a similar rule as IDPA for the Production and Carry Optics
replace factory mag releases and other small parts with factory or
3rd-party parts and remain legal in those divisions.
https://www.brownells.com/handgun-parts/frame-parts/magazine-release-parts/magazine-releases/vickers-glock-extended-magazine-release-prod25364.aspx?sku=100-700-094&avs%7cManufacturer_1=tangodown
These are the 3rd-party parts I prefer:
https://www.brownells.com/handgun-parts/frame-parts/slide-catch-parts/slide-catches/enhanced-slide-stop-for-glock--prod42969.aspx
pin retainers, pins, extractors, magazine releases, slide stops, thumb
"Appendix D4
21.6 Exchange of minor External components Sights, firing pins, firing
safeties, triggers, hammers, bushings, and ejectors MAY be replaced with
OFM or aftermarket parts.”