[argyllcms] Re: problems with Quato DTP94 and Eizo FS2331
- From: Andre Bischof <andre.bischof@xxxxxxxxxxxx>
- To: argyllcms@xxxxxxxxxxxxx
- Date: Mon, 29 Jul 2013 17:24:28 +0200
Am 29.07.2013 15:54, schrieb Graeme Gill:
Andre Bischof wrote:
( is it right to press "A" here? If not, please tell me what key to hit.)
Hi,
you should simply press space or return. Pressing a capital
letter is for setting up FWA compensation using a spectral instrument.
icoms: About to return read 'X -102.31^IY -107.04^IZ -154.62^M<00>' ICOM
err 0x0
icoms: Write_Read Write_Read success, returning 'X -102.31^IY -107.04^IZ
-154.62^M<00>'
Looks like something is wrong with the instrument itself, almost as if
it has had a black calibration done on a white reference.
Run dispcal again with the -J option, and make sure you follow the
instructions and calibrate the instrument against absolute black, ie.
make sure the instrument is against a black surface and shielded from
direct light.
You don't have to complete the dispcal, just go through the instrument
calibration and exit.
Try a spotread again after that, and see if the readings look more reasonable.
Alright, I did "dispwin -d2 -m" for white:
root@linux:~# dispcal -J -yl
Place cap on the instrument, or place in on a dark surface,
or place on the white calibration reference,
and then hit any key to continue,
or hit Esc or Q to abort:
Calibration complete
[...]
and afterwards spotread again:
# spotread -D8 -yl
usb_get_paths about to look through buses:
[...]
dtp92: About to init coms
dtp92Q/dtp94: About to init USB
icoms: About to set usb port characteristics
icoms: About to open the USB port, tries 0
icoms: USB port needs opening
icoms: About to open USB port 'usb:/bus0/dev2 (Xrite DTP94)'
open() of USB port 'usb:/bus0/dev2 (Xrite DTP94)' suceeded
Number of configurations = 1
icoms: USB port is now open
icoms: Clearing any USB errors
icoms: usb port characteristics set ok
[...]
icoms: Write_Read called with '0117CF^M'
icoms: About to write '0117CF^M' ICOM err 0x0
icoms: Read called
icoms: About to return read '<00>' ICOM err 0x0
icoms: Write_Read Write_Read success, returning '<00>'
dtp92: instrument inited OK
icoms: Write_Read called with '0216CF^M'
icoms: About to write '0216CF^M' ICOM err 0x0
icoms: Read called
icoms: About to return read '<00>' ICOM err 0x0
icoms: Write_Read Write_Read success, returning '<00>'
Place instrument on spot to be measured,
and hit [A-Z] to read white and setup FWA compensation (keyed to letter)
[a-z] to read and make FWA compensated reading from keyed reference
'r' to set reference, 's' to save spectrum,
'h' to toggle high res., 'k' to do a calibration
Hit ESC or Q to exit, any other key to take a reading:
icoms: Write_Read called with 'RM^M'
icoms: About to write 'RM^M' ICOM err 0x0
icoms: Read called
icoms: About to return read 'X 176.20^IY 183.11^IZ 250.29^M<00>'
ICOM err 0x0
icoms: Write_Read Write_Read success, returning 'X 176.20^IY
183.11^IZ 250.29^M<00>'
Result is XYZ: 176.200000 183.110000 250.290000, D50 Lab: 125.915123
-0.409870 -44.860192
Place instrument on spot to be measured,
and hit [A-Z] to read white and setup FWA compensation (keyed to letter)
[a-z] to read and make FWA compensated reading from keyed reference
'r' to set reference, 's' to save spectrum,
'h' to toggle high res., 'k' to do a calibration
Hit ESC or Q to exit, any other key to take a reading:
------------------------------
now switched dispwin to black
------------------------------
icoms: Write_Read called with 'RM^M'
icoms: About to write 'RM^M' ICOM err 0x0
icoms: Read called
icoms: About to return read 'X 0.08^IY 0.08^IZ 0.12^M<00>'
ICOM err 0x0
icoms: Write_Read Write_Read success, returning 'X 0.08^IY
0.08^IZ 0.12^M<00>'
Result is XYZ: 0.080000 0.080000 0.120000, D50 Lab: 0.722637 0.115651
-1.019669
Place instrument on spot to be measured,
and hit [A-Z] to read white and setup FWA compensation (keyed to letter)
[a-z] to read and make FWA compensated reading from keyed reference
'r' to set reference, 's' to save spectrum,
'h' to toggle high res., 'k' to do a calibration
Hit ESC or Q to exit, any other key to take a reading:
Spot read stopped at user request!
Hit Esc or Q to give up, any other key to retry:
icoms: delete called
icoms: closing port
usb_close_port() called
usb port has been released and closed
root@linux:~#
Looks like the value are not negativ any more - are they more reasonable
for you?
What am I supposed to do next?
You're really helpful, thanks so far!
Cheers
Andre
Other related posts:
