[aodvv2-discuss] Re: Stock take

  • From: Victoria Mercieca <vmercieca0@xxxxxxxxx>
  • To: "aodvv2-discuss@xxxxxxxxxxxxx" <aodvv2-discuss@xxxxxxxxxxxxx>
  • Date: Sat, 10 Oct 2015 22:12:53 +0100

Hi all,

Attached is the latest version of the draft. I changed the metrics section
to the text above. Awaiting feedback on whether to add some of the other
smaller bits of text.

I will start proofreading this tomorrow.

Regards,
Vicky.

On Sat, Oct 10, 2015 at 3:56 PM, Charlie Perkins <
charles.perkins@xxxxxxxxxxxxx> wrote:

Hello folks,

I did not get any feedback about whether you would like an Internet Draft
about RFC 6621 considerations.

I'll write one on Monday and float it past the group. Posting the new
draft does not have to wait for this. I'll also write a latency metric
draft. Both of these will be very short. The RFC 6621 draft will be, at
best, informational. Or, even better, [manet] will decide that it's far
too trivial to deserve publication.

Regards,
Charlie P.



On 10/9/2015 12:24 AM, Victoria Mercieca wrote:

Hi all,

I did a summary for myself the other day of issues I would like cleared up
before publishing version 12. They were:

seqnum arithmetic text
directional metrics
metric types
RFC 6621 multicast reduction.


SEQNUM
---------------
I'm happy with the seqnum text if you all are. To summarise, the bit about
the arithmetic says this (unchanged since I pasted it last time):

Comparing the sequence number will identify which information is stale.
The currently stored sequence number is subtracted from the incoming
sequence number. The result of the subtraction is to be interpreted as a
signed 16-bit integer, and if less than zero, then the information in the
AODVv2 message is stale and MUST be discarded.

I was wondering where to put in any reference to the Newer function
Charlie wrote? And if we should we add any explanation that if the incoming
sequence number is greater than the current seqnum by more than half the
maximum value, then the incoming will be seen as stale? But that we dont
care, because if that happened, something bigger is wrong...?


Did you have any response to my discussion on the latter paragraph?



METRICS
---------------
I think this is resolved with the new text, if you all agree? I havent yet
replaced it or moved the hopcount specific definitions to later in the
document.

# Metrics {#metrics}

Metrics measure a cost or quality associated with a route or a link, e.g.,
latency, delay, financial cost, energy, etc. Metric values are reported in
route messages, where the goal is to determine a route between OrigAddr and
TargAddr. In Route Request messages, the metric describes the cost of the
route from OrigAddr (the router client) to the router sending the Route
Request. The receiving router calculates the cost from OrigAddr to itself,
combining the metric value from the message with knowledge of the link cost
from the sender to the receiver, i.e., the incoming link cost. This updated
route cost is included when regenerating the Route Request message. In
Route Reply messages, the metric reflects the cost of the route from
TargAddr (the router client) to the router sending the Route Reply. Routes
to OrigAddr and TargAddr are installed at intermediate routers for the
purposes of forwarding a Route Reply message and subsequent data traffic
between OrigAddr and TargAddr. Assuming link metrics are symmetric, the
cost of the routes to OrigAddr and TargAddr installed at each router will
be correct.

AODVv2 enables the use of multiple metric types. Each route discovery
attempt indicates which metric type is requested for the route. For each
MetricType, AODVv2 requires:

* A MetricType number, to indicate the metric type of a route. MetricType
numbers allocated are detailed in [](#metric-type).
* A maximum value, denoted MAX_METRIC[MetricType]. If the cost of a route
exceeds MAX_METRIC[MetricType], the route is ignored. AODVv2 cannot store
routes that cost more than MAX_METRIC[MetricType].
* A function for incoming link cost, denoted Cost(L). Using incoming link
costs means that the route learned has a path optimized for the direction
from OrigAddr to TargAddr.
* A function for route cost, denoted Cost(R).
* A function to analyze routes for potential loops, denoted LoopFree(R1,
R2). LoopFree verifies that a route R2 is not a sub-section of another
route R1. An AODVv2 router invokes LoopFree() as part of the process in
[](#test), when an advertised route (R1) and an existing route (R2) have
the same destination address, metric type, and sequence number.

AODVv2 currently supports cost metrics where Cost(R) is strictly
increasing, by defining:

* Cost(R) := Sum of Cost(L) of each link in the route
* LoopFree(R1, R2) := ( Cost(R1) \<= Cost(R2) )

Definitions of Cost and LoopFree functions for other metric types are
future development tasks.


This is fine with me.


6621
-------
This bit still confuses me (sorry Charlie). I will take your collective
advice on this section. The previous text:

Implementations are free to choose their own heuristics for reducing
multicast overhead. Some methods for doing so are described in
[](#RFC6621). AODVv2 does not specify which method to use to restrict the
set of AODVv2 routers that have the responsibility to regenerate multicast
messages. Note that multicast messages MAY be sent via unicast. For
example, this may occur for certain link-types (non-broadcast media), for
manually configured router adjacencies, or in order to improve robustness.

Which received comments about interoperability if different techniques
were chosen at different routers, and also comments that tie in with my own
confusion about how 6621 supports "flooding an identical copy of a message
to all destinations inside the MANET" rather than the ability to modify the
message before retransmitting which is what we need.


Did you see my suggestion about this point?


Regarding interoperability:
Stan's suggested text, slightly altered by Charlie's comment:

Any text changed in the spec needs to include the above. Here’s my
suggested text: “Implementations MAY choose to employ techniques to reduce
the number of multicast messages sent. Use of {RFC 6621] in deployments is
recommended. Employing [RFC 6621] in a subset of the operational AODVv2
routers in a network will not cause interoperability issues, but might
reduce the effectiveness of the multicast reduction scheme.”


This is fine with me.


I've replaced the current text with this suggestion. Just checking though
- Does the same apply if the 6621 setup uses different algorithms on
different routers?...in which case I should add that to the text to make it
extra clear.


Yes, it does apply.


If we're all in agreement on this I can make the final updates tonight.
Could do with some proofreading again I think, but we could post to MANET
on Monday?


I would like that.




Kind regards,

Vicky.

On Thu, Oct 8, 2015 at 10:02 PM, Ratliff, Stanley < <sratliff@xxxxxxxxxxx>
sratliff@xxxxxxxxxxx> wrote:

Yes, unless there are pressing issues that are hanging (Pressing, of
course, being in the eye of the beholder). Hence, I guess, the reason for
the email. J



Regards,

Stan





*From:* aodvv2-discuss-bounce@xxxxxxxxxxxxx [mailto:
aodvv2-discuss-bounce@xxxxxxxxxxxxx] *On Behalf Of *Charlie Perkins
*Sent:* Thursday, October 08, 2015 4:55 PM
*To:* aodvv2-discuss@xxxxxxxxxxxxx
*Subject:* [aodvv2-discuss] Re: Stock take



Shouldn't we issue the draft ASAP?

Regards,
Charlie P.

On 10/8/2015 10:45 AM, John Dowdell wrote:

Hi all

We need to be on final approach for Yokohama now. What open issues are we
facing please, and which of these do we need to take to the manet list?

Thanks
John



_____________________________________________________
This electronic message and any files transmitted with it contains
information from iDirect, which may be privileged, proprietary
and/or confidential. It is intended solely for the use of the individual
or entity to whom they are addressed. If you are not the original
recipient or the person responsible for delivering the email to the
intended recipient, be advised that you have received this email
in error, and that any use, dissemination, forwarding, printing, or
copying of this email is strictly prohibited. If you received this email
in error, please delete it and immediately notify the sender.
_____________________________________________________








Mobile Ad hoc Networks Working Group C. Perkins
Internet-Draft Futurewei
Intended status: Standards Track S. Ratliff
Expires: April 12, 2016 Idirect
J. Dowdell
Airbus Defence and Space
L. Steenbrink
HAW Hamburg, Dept. Informatik
V. Mercieca
Airbus Defence and Space
October 10, 2015


Ad Hoc On-demand Distance Vector Routing Version 2 (AODVv2)
draft-ietf-manet-aodvv2-12

Abstract

The Ad Hoc On-demand Distance Vector Version 2 (AODVv2) routing
protocol is intended for use by mobile routers in wireless, multihop
networks. AODVv2 determines unicast routes among AODVv2 routers
within the network in an on-demand fashion, offering rapid
convergence in dynamic topologies.

Status of This Memo

This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on April 12, 2016.

Copyright Notice

Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents



Perkins, et al. Expires April 12, 2016 [Page 1]

Internet-Draft AODVv2 October 2015


(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Applicability Statement . . . . . . . . . . . . . . . . . . . 10
4. Data Structures . . . . . . . . . . . . . . . . . . . . . . . 11
4.1. Interface List . . . . . . . . . . . . . . . . . . . . . 11
4.2. Router Client Table . . . . . . . . . . . . . . . . . . . 11
4.3. Neighbor Table . . . . . . . . . . . . . . . . . . . . . 12
4.4. Sequence Numbers . . . . . . . . . . . . . . . . . . . . 13
4.5. Multicast Route Message Table . . . . . . . . . . . . . . 13
4.6. Route Table . . . . . . . . . . . . . . . . . . . . . . . 15
5. Metrics . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6. AODVv2 Protocol Operations . . . . . . . . . . . . . . . . . 17
6.1. Initialization . . . . . . . . . . . . . . . . . . . . . 18
6.2. Adjacency Monitoring . . . . . . . . . . . . . . . . . . 18
6.3. Neighbor Table Update . . . . . . . . . . . . . . . . . . 20
6.4. Interaction with Forwarding Plane . . . . . . . . . . . . 21
6.5. Message Transmission . . . . . . . . . . . . . . . . . . 22
6.6. Route Discovery, Retries and Buffering . . . . . . . . . 23
6.7. Processing Received Route Information . . . . . . . . . . 25
6.7.1. Evaluating Route Information . . . . . . . . . . . . 26
6.7.2. Applying Route Updates . . . . . . . . . . . . . . . 27
6.8. Suppressing Redundant Messages Using the Multicast Route
Message Table . . . . . . . . . . . . . . . . . . . . . . 29
6.9. Route Maintenance . . . . . . . . . . . . . . . . . . . . 31
6.9.1. Route State . . . . . . . . . . . . . . . . . . . . . 31
6.9.2. Reporting Invalid Routes . . . . . . . . . . . . . . 34
7. AODVv2 Protocol Messages . . . . . . . . . . . . . . . . . . 34
7.1. Route Request (RREQ) Message . . . . . . . . . . . . . . 34
7.1.1. RREQ Generation . . . . . . . . . . . . . . . . . . . 36
7.1.2. RREQ Reception . . . . . . . . . . . . . . . . . . . 37
7.1.3. RREQ Regeneration . . . . . . . . . . . . . . . . . . 38
7.2. Route Reply (RREP) Message . . . . . . . . . . . . . . . 39
7.2.1. RREP Generation . . . . . . . . . . . . . . . . . . . 41
7.2.2. RREP Reception . . . . . . . . . . . . . . . . . . . 42
7.2.3. RREP Regeneration . . . . . . . . . . . . . . . . . . 44
7.3. Route Reply Acknowledgement (RREP_Ack) Message . . . . . 45
7.3.1. RREP_Ack Generation . . . . . . . . . . . . . . . . . 45
7.3.2. RREP_Ack Reception . . . . . . . . . . . . . . . . . 45



Perkins, et al. Expires April 12, 2016 [Page 2]

Internet-Draft AODVv2 October 2015


7.4. Route Error (RERR) Message . . . . . . . . . . . . . . . 46
7.4.1. RERR Generation . . . . . . . . . . . . . . . . . . . 47
7.4.2. RERR Reception . . . . . . . . . . . . . . . . . . . 49
7.4.3. RERR Regeneration . . . . . . . . . . . . . . . . . . 50
8. RFC 5444 Representation . . . . . . . . . . . . . . . . . . . 51
8.1. RREQ . . . . . . . . . . . . . . . . . . . . . . . . . . 52
8.1.1. Message Header . . . . . . . . . . . . . . . . . . . 52
8.1.2. Message TLV Block . . . . . . . . . . . . . . . . . . 52
8.1.3. Address Block . . . . . . . . . . . . . . . . . . . . 52
8.1.4. Address Block TLV Block . . . . . . . . . . . . . . . 53
8.2. RREP . . . . . . . . . . . . . . . . . . . . . . . . . . 53
8.2.1. Message Header . . . . . . . . . . . . . . . . . . . 53
8.2.2. Message TLV Block . . . . . . . . . . . . . . . . . . 54
8.2.3. Address Block . . . . . . . . . . . . . . . . . . . . 54
8.2.4. Address Block TLV Block . . . . . . . . . . . . . . . 54
8.3. RREP_Ack . . . . . . . . . . . . . . . . . . . . . . . . 55
8.3.1. Message Header . . . . . . . . . . . . . . . . . . . 55
8.3.2. Message TLV Block . . . . . . . . . . . . . . . . . . 55
8.3.3. Address Block . . . . . . . . . . . . . . . . . . . . 55
8.3.4. Address Block TLV Block . . . . . . . . . . . . . . . 56
8.4. RERR . . . . . . . . . . . . . . . . . . . . . . . . . . 56
8.4.1. Message Header . . . . . . . . . . . . . . . . . . . 56
8.4.2. Message TLV Block . . . . . . . . . . . . . . . . . . 56
8.4.3. Address Block . . . . . . . . . . . . . . . . . . . . 56
8.4.4. Address Block TLV Block . . . . . . . . . . . . . . . 56
9. Simple External Network Attachment . . . . . . . . . . . . . 57
10. Optional Features . . . . . . . . . . . . . . . . . . . . . . 58
10.1. Expanding Rings Multicast . . . . . . . . . . . . . . . 59
10.2. Precursor Lists . . . . . . . . . . . . . . . . . . . . 59
10.3. Intermediate RREP . . . . . . . . . . . . . . . . . . . 60
10.4. Message Aggregation Delay . . . . . . . . . . . . . . . 60
11. Configuration . . . . . . . . . . . . . . . . . . . . . . . . 60
11.1. Timers . . . . . . . . . . . . . . . . . . . . . . . . . 61
11.2. Protocol Constants . . . . . . . . . . . . . . . . . . . 62
11.3. Local Settings . . . . . . . . . . . . . . . . . . . . . 63
11.4. Network-Wide Settings . . . . . . . . . . . . . . . . . 63
11.5. Optional Feature Settings . . . . . . . . . . . . . . . 63
12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 64
12.1. RFC 5444 Message Types . . . . . . . . . . . . . . . . . 64
12.2. RFC 5444 Address Block TLV Types . . . . . . . . . . . . 64
12.3. MetricType Allocation . . . . . . . . . . . . . . . . . 65
12.4. AddressType Allocation . . . . . . . . . . . . . . . . . 65
13. Security Considerations . . . . . . . . . . . . . . . . . . . 66
14. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 68
15. References . . . . . . . . . . . . . . . . . . . . . . . . . 69
15.1. Normative References . . . . . . . . . . . . . . . . . . 69
15.2. Informative References . . . . . . . . . . . . . . . . . 70
Appendix A. Multi-homing Considerations . . . . . . . . . . . . 71



Perkins, et al. Expires April 12, 2016 [Page 3]

Internet-Draft AODVv2 October 2015


Appendix B. Router Client Relocation . . . . . . . . . . . . . . 71
Appendix C. Example Algorithms for AODVv2 Operations . . . . . . 72
C.1. HopCount MetricType . . . . . . . . . . . . . . . . . . . 74
C.2. General Operations . . . . . . . . . . . . . . . . . . . 74
C.2.1. Check_Route_State . . . . . . . . . . . . . . . . . . 74
C.2.2. Process_Routing_Info . . . . . . . . . . . . . . . . 75
C.2.3. Fetch_Route_Table_Entry . . . . . . . . . . . . . . . 76
C.2.4. Update_Route_Table_Entry . . . . . . . . . . . . . . 77
C.2.5. Create_Route_Table_Entry . . . . . . . . . . . . . . 78
C.2.6. LoopFree . . . . . . . . . . . . . . . . . . . . . . 78
C.2.7. Fetch_Rte_Msg_Table_Entry . . . . . . . . . . . . . . 79
C.2.8. Update_Rte_Msg_Table . . . . . . . . . . . . . . . . 79
C.2.9. Build_RFC_5444_Message_Header . . . . . . . . . . . . 80
C.3. RREQ Operations . . . . . . . . . . . . . . . . . . . . . 81
C.3.1. Generate_RREQ . . . . . . . . . . . . . . . . . . . . 81
C.3.2. Receive_RREQ . . . . . . . . . . . . . . . . . . . . 82
C.3.3. Regenerate_RREQ . . . . . . . . . . . . . . . . . . . 83
C.4. RREP Operations . . . . . . . . . . . . . . . . . . . . . 85
C.4.1. Generate_RREP . . . . . . . . . . . . . . . . . . . . 85
C.4.2. Receive_RREP . . . . . . . . . . . . . . . . . . . . 86
C.4.3. Regenerate_RREP . . . . . . . . . . . . . . . . . . . 87
C.5. RREP_Ack Operations . . . . . . . . . . . . . . . . . . . 88
C.5.1. Generate_RREP_Ack . . . . . . . . . . . . . . . . . . 89
C.5.2. Receive_RREP_Ack . . . . . . . . . . . . . . . . . . 89
C.5.3. Timeout_RREP_Ack . . . . . . . . . . . . . . . . . . 89
C.6. RERR Operations . . . . . . . . . . . . . . . . . . . . . 89
C.6.1. Generate_RERR . . . . . . . . . . . . . . . . . . . . 89
C.6.2. Receive_RERR . . . . . . . . . . . . . . . . . . . . 91
C.6.3. Regenerate_RERR . . . . . . . . . . . . . . . . . . . 92
Appendix D. AODVv2 Draft Updates . . . . . . . . . . . . . . . . 94
D.1. Changes between revisions 11 and 12 . . . . . . . . . . . 94
D.2. Changes between revisions 10 and 11 . . . . . . . . . . . 95
D.3. Changes between revisions 9 and 10 . . . . . . . . . . . 96
D.4. Changes between revisions 8 and 9 . . . . . . . . . . . . 96
D.5. Changes between revisions 7 and 8 . . . . . . . . . . . . 99
D.6. Changes between revisions 6 and 7 . . . . . . . . . . . . 100
D.7. Changes between revisions 5 and 6 . . . . . . . . . . . . 101
D.8. Changes between revisions 4 and 5 . . . . . . . . . . . . 102
D.9. Changes between revisions 3 and 4 . . . . . . . . . . . . 103
D.10. Changes between revisions 2 and 3 . . . . . . . . . . . . 104
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 105

1. Overview

The Ad Hoc On-demand Distance Vector Version 2 (AODVv2) routing
protocol (formerly named DYMO) enables on-demand, multihop unicast
routing among AODVv2 routers in mobile ad hoc networks (MANETs)
[RFC2501].



Perkins, et al. Expires April 12, 2016 [Page 4]

Internet-Draft AODVv2 October 2015


Compared to AODV [RFC3561], AODVv2 makes some features optional,
notably intermediate route replies, expanding ring search, and
precursor lists. Hello messages and local repair have been removed.
Message formats have been updated and made compliant with [RFC5444].
AODVv2 also provides a mechanism for the use of multiple metric
types.

The basic operations of the AODVv2 protocol are route discovery and
route maintenance.

Route discovery is performed when an AODVv2 router needs to forward
an IP packet for one of its clients, but does not have a valid route
to the packet's destination. AODVv2 routers use Route Request (RREQ)
and Route Reply (RREP) messages to carry route information between
the originator of the route discovery and the target, establishing a
route to both endpoints on all intermediate routers. A metric value
is included to represent the cost of the route contained within the
message.

AODVv2 uses sequence numbers to identify stale routing information,
and compares route metric values to determine if advertised routes
could form loops.

Route maintenance involves monitoring the router's links and routes
for changes. This includes confirming bidirectionality of links to
other AODVv2 routers, issuing Route Error messages if link failures
invalidate routes, extending and enforcing route timeouts, and
reacting to received Route Error messages.

AODVv2 control plane messages use the Generalized MANET Packet/
Message Format defined in [RFC5444] and the parameters in [RFC5498].
AODVv2 defines a set of data elements which map to [RFC5444] Address
Blocks, Address Block TLVs, and Message TLVs.

Security for authentication of AODVv2 routers and encryption of
control messages is accomplished using the TIMESTAMP and ICV TLVs
defined in [RFC7182].

2. Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
[RFC2119]. In addition, this document uses terminology from
[RFC5444], and defines the following terms:

AddressList
An AODVv2 Data Element containing a list of IP addresses.



Perkins, et al. Expires April 12, 2016 [Page 5]

Internet-Draft AODVv2 October 2015


Adjacency
A bi-directional link between neighboring AODVv2 routers for the
purpose of routing information.

AckReq
An AODVv2 Data Element used in a Route Reply message to request
that the Route Reply message is acknowledged by returning a Route
Reply Ack message. This data element contains the address of the
AODVv2 router that should acknowledge the Route Reply message.

AdvRte
A route advertised in an incoming route message

AODVv2 Router
An IP addressable device in the ad hoc network that performs the
AODVv2 protocol operations specified in this document.

CurrentTime
The current time as maintained by the AODVv2 router.

Data Element
A named field used within AODVv2 protocol messages.

Disregard
Ignore for further processing.

ENAR (External Network Access Router)
An AODVv2 router with an interface to an external, non-AODVv2
network.

Invalid route
A route that cannot be used for forwarding.

MANET
A Mobile Ad Hoc Network as defined in [RFC2501].

MetricType
An AODVv2 Data Element indicating the metric type for a metric
value included in a message.

MetricTypeList
An AODVv2 Data Element used in a Route Error message, containing a
list of metric types associated with the addresses in the
AddressList of the message.

msg_hop_limit
An [RFC5444] message field, indicating the number of hops the
message is allowed to traverse.



Perkins, et al. Expires April 12, 2016 [Page 6]

Internet-Draft AODVv2 October 2015


msg_hop_count
An [RFC5444] message field, indicating the number of hops
traversed so far by the message.

Neighbor
An AODVv2 router from which an AODVv2 message has been received.
Neighbors exchange routing information and attempt to verify
bidirectionality of the link to a neighbor before installing a
route via that neighbor.


Node
An IP addressable device in the ad hoc network. All nodes in this
document are either AODVv2 Routers or Router Clients.

OrigAddr (Originator Address)
An AODVv2 Data Element containing the source IP address of the IP
packet triggering route discovery.

OrigMetric
An AODVv2 Data Element containing the metric value associated with
the route to the OrigAddr in a message.

OrigPrefixLen
The prefix length, in bits, associated with OrigAddr.

OrigSeqNum
An AODVv2 Data Element used in a Route Request message, containing
the sequence number of the AODVv2 router which originated the
Route Request.

PktSource
An AODVv2 Data Element used in a Route Error message, containing
the source address of the IP packet which triggered the Route
Error message.

PrefixLengthList
An AODVv2 Data Element containing a list of routing prefix lengths
associated with the addresses in the AddressList of the message.

Reactive
A protocol operation is called "reactive" if it is performed only
in reaction to specific events. In this document, "reactive" is
synonymous with "on-demand".

RERR (Route Error)
The AODVv2 message type used to indicate that an AODVv2 router
does not have a route toward one or more particular destinations.



Perkins, et al. Expires April 12, 2016 [Page 7]

Internet-Draft AODVv2 October 2015


RERR_Gen (RERR Generating Router)
The AODVv2 router generating a Route Error message.

Routable Unicast IP Address
A routable unicast IP address is a unicast IP address that is
scoped sufficiently to be forwarded by a router. Globally-scoped
unicast IP addresses and Unique Local Addresses (ULAs) ([RFC4193])
are examples of routable unicast IP addresses.

Router Client
An address or address range configured on an AODVv2 router,
corresponding to one or more nodes which require that router to
initiate and respond to route discoveries on their behalf, so that
they can send and receive IP traffic to and from remote
destinations. The AODVv2 router's interface addresses are also
configured as Router Clients.

RREP (Route Reply)
The AODVv2 message type used to reply to a Route Request message.

RREP_Gen (RREP Generating Router)
The AODVv2 router configured with TargAddr as a Router Client,
i.e., the router that creates the Route Reply message.

RREQ (Route Request)
The AODVv2 message type used to discover a route to the Target
Address and distribute information about the route to the
Originator Address.

RREQ_Gen (RREQ Generating Router)
The AODVv2 router that creates the Route Request message on behalf
of a Router Client.

RteMsg (Route Message)
A Route Request (RREQ) or Route Reply (RREP) message.

Sequence Number (SeqNum)
An AODVv2 Data Element containing the sequence number maintained
by an AODVv2 router to indicate freshness of route information.

SeqNumList
An AODVv2 Data Element containing a list of sequence numbers
associated with the addresses in the AddressList of a message.

TargAddr (Target Address)
An AODVv2 Data Element containing the destination address of the
IP packet triggering route discovery.




Perkins, et al. Expires April 12, 2016 [Page 8]

Internet-Draft AODVv2 October 2015


TargMetric
An AODVv2 Data Element containing the metric value associated with
the route to the TargAddr in a message.

TargPrefixLen
The prefix length, in bits, associated with TargAddr.

TargSeqNum
An AODVv2 Data Element used in a Route Reply message, containing
the sequence number of the AODVv2 router which originated the
Route Reply.

Valid route
A route that can be used for forwarding.

Unreachable Address
An address reported in an RERR message, either the destination
address of an IP packet that could not be forwarded because a
valid route to the destination is not known, or the address on a
route which became Invalid.

Upstream
In the direction from destination to source (from TargAddr to
OrigAddr).

ValidityTime
An AODVv2 Data Element containing the length of time the route
described by the message is offered.

The AODVv2 Data Elements are used to create AODVv2 messages. Their
contents are transferred into [RFC5444] formatted messages
(Section 8) before sending.

This document uses the notational conventions in Table 1 to simplify
the text.

+-----------------------+------------------------------------+
| Notation | Meaning |
+-----------------------+------------------------------------+
| Route[Address] | A route toward Address |
| Route[Address].Field | A field in a route toward Address |
| RteMsg.Field | A field in either RREQ or RREP |
+-----------------------+------------------------------------+

Table 1: Notational Conventions






Perkins, et al. Expires April 12, 2016 [Page 9]

Internet-Draft AODVv2 October 2015


3. Applicability Statement

The AODVv2 routing protocol is a reactive routing protocol. Certain
interactions with the forwarding plane are required, and these are
discussed in Section 6.4.

AODVv2 is designed for stub or disconnected mobile ad hoc networks,
i.e., non-transit networks or those not connected to the internet.
AODVv2 can, however, be configured to perform gateway functions when
attached to external networks, as discussed in Section 9.

AODVv2 handles a wide variety of mobility and traffic patterns by
determining routes on-demand. In networks with a large number of
routers, AODVv2 is best suited for relatively sparse traffic
scenarios where each router forwards IP packets to a small percentage
of other AODVv2 routers in the network. In this case fewer routes
are needed, and therefore less control traffic is produced.

Providing security for a reactive routing protocol can be difficult.
AODVv2 provides for message integrity and security against replay
attacks by using integrity check values, timestamps and sequence
numbers, as described in Section 13. If security associations can be
established, encryption can be used for AODVv2 messages to ensure
that only trusted routers participate in routing operations.

Since the route discovery process typically results in a route being
established in both directions along the same path, uni-directional
links are not suitable. AODVv2 will detect and exclude those links
from route discovery. The route discovered is optimised for the
requesting router, and the return path may not be the optimal route.

AODVv2 is applicable to memory constrained devices, since only a
little routing state is maintained in each AODVv2 router. In
contrast to proactive routing protocols, which maintain routing
information for all destinations within the MANET, AODVv2 routes that
are not needed for forwarding data do not need to be maintained. On
routers unable to store persistent AODVv2 state, recovery can impose
a performance penalty (e.g., in case of AODVv2 router reboot), since
if a router loses its sequence number, there is a delay before the
router can resume full operations.

AODVv2 supports routers with multiple interfaces, as long as each
interface configured for AODVv2 has a unicast IP address. A router
may use the same IP address on multiple interfaces. Address
assignment procedures are out of scope for AODVv2.

AODVv2 supports hosts with multiple interfaces, as long as each
interface is configured with its own unicast IP address. Multi-



Perkins, et al. Expires April 12, 2016 [Page 10]

Internet-Draft AODVv2 October 2015


homing of an IP address is not supported by AODVv2, and therefore a
Router Client, i.e. an IP Address, SHOULD NOT be served by more than
one AODVv2 router at any one time. Appendix A contains some notes on
this topic.

Although AODVv2 is closely related to AODV [RFC3561], and shares some
features of DSR [RFC4728], AODVv2 is not interoperable with either of
those protocols.

The routing algorithm in AODVv2 MAY be operated at layers other than
the network layer, using layer-appropriate addresses.

4. Data Structures

4.1. Interface List

If multiple interfaces of the AODVv2 router are configured for use by
AODVv2, a list of the interfaces SHOULD be configured in the
AODVv2_INTERFACES list.

4.2. Router Client Table

An AODVv2 router MUST provide route discovery services for its own
local applications and for other non-routing nodes that are reachable
without traversing another AODVv2 router. These nodes, and the
AODVv2 router itself, are referred to as Router Clients. An AODVv2
router will only send Route Request and Route Reply messages on
behalf of configured Router Clients.

Router Client Table entries MUST contain:

RouterClient.IPAddress
An IP address or the start of an address range that requires route
discovery services from the AODVv2 router.

RouterClient.PrefixLength
The length, in bits, of the routing prefix associated with the
RouterClient.IPAddress. If a prefix length is included, the
AODVv2 router MUST provide connectivity for all addresses within
that prefix.

RouterClient.Cost
The cost associated with reaching this Router Client. This cost
will also appear as the metric in a route table entry for the
Router Client address.






Perkins, et al. Expires April 12, 2016 [Page 11]

Internet-Draft AODVv2 October 2015


The Router Client Table for an AODVv2 router is never empty, since an
AODVv2 router is always its own client. The IP Addresses of the
router's interfaces will appear in the Router Client Table.

The Router Client list contains information on all addresses for
which the AODVv2 router needs to initiate and respond to route
discoveries. In the initial state, an AODVv2 router is not required
to have information about the Router Clients of any other AODVv2
router.

A Router Client address MUST NOT be served by more than one AODVv2
router at any one time, i.e. a Router Client of one AODVv2 router
MUST NOT be configured as a Router Client on another AODVv2 router
using the same Router Client IP address. Shifting responsibility for
a Router Client to a different AODVv2 router is discussed in
Appendix B.

4.3. Neighbor Table

A neighbor table MUST be maintained with information about
neighboring AODVv2 routers which are used in discovered routes,
including an indication of the state of the adjacency to the router.
Section 6.2 discusses how to monitor adjacency.

Neighbor Table entries MUST contain:

Neighbor.IPAddress
An IP address of the neighboring router, the source IP address of
a received route message.

Neighbor.State
The state of the adjacency with the neighbor (Confirmed, Unknown,
or Blacklisted)

Neighbor.ResetTime
The time at which this router SHOULD no longer be considered
blacklisted. By default this value is calculated at the time the
router is blacklisted and is equal to CurrentTime +
MAX_BLACKLIST_TIME. After this time, the state SHOULD be reset to
Unknown. While the neighbor is not marked as blacklisted, this
value SHOULD be set to INFINITY_TIME.

Neighbors are marked as Blacklisted when they fail to confirm
adjacency when requested (see Section 6.2).







Perkins, et al. Expires April 12, 2016 [Page 12]

Internet-Draft AODVv2 October 2015


4.4. Sequence Numbers

Sequence numbers enable AODVv2 routers to determine the temporal
order of route discovery messages, identifying stale routing
information so that it can be discarded. The sequence number
fulfills the same roles as the "Destination Sequence Number" of DSDV
[Perkins94], and the AODV Sequence Number in [RFC3561].

Each AODVv2 router in the network MUST maintain its own sequence
number as a 16-bit unsigned integer.

All RREQ and RREP messages created by an AODVv2 router include the
router's sequence number. Each AODVv2 router MUST ensure that its
sequence number is strictly increasing. It is incremented by one (1)
whenever an RREQ or RREP is created, except when the sequence number
is 65,535 (the maximum value of a 16-bit unsigned integer), in which
case it MUST be reset to one (1). The value zero (0) is reserved to
indicate that the sequence number for an address is unknown.

An AODVv2 router can only attach its own sequence number to
information about a route to one of its configured router clients.
All route messages regenerated by other routers retain the
originator's sequence number. Therefore, when two pieces of
information about a route are received, they both contain a sequence
number from the originating router. Comparing the sequence number
will identify which information is stale. The currently stored
sequence number is subtracted from the incoming sequence number. The
result of the subtraction is to be interpreted as a signed 16-bit
integer, and if less than zero, then the information in the AODVv2
message is stale and MUST be discarded.

As a consequence, loop freedom is assured.

An AODVv2 router SHOULD maintain its sequence number in persistent
storage. If the sequence number is lost, the router MUST follow the
procedure in Section 6.1 to safely resume routing operations with a
new sequence number.

4.5. Multicast Route Message Table

A route message (RteMsg) is either a Route Request or Route Reply
message. The Multicast Route Message Table is a conceptual table
which contains information about previously received multicast route
messages, so that when a route message is received, an AODVv2 router
can determine if the incoming information is redundant, and avoid
unnecessary regeneration of the route message.





Perkins, et al. Expires April 12, 2016 [Page 13]

Internet-Draft AODVv2 October 2015


A Multicast Route Message Table entry MUST contain the following
information:

RteMsg.MessageType
Either RREQ or RREP.

RteMsg.OrigAddr
An IP address of the node which requires the route, i.e., the
source address of the IP packet triggering the route request.

RteMsg.OrigPrefixLen
The prefix length associated with OrigAddr.

RteMsg.TargAddr
An IP address of the target, i.e., the destination address of the
IP packet triggering the route request.

RteMsg.TargPrefixLen
The prefix length associated with TargAddr.

RteMsg.OrigSeqNum
The sequence number associated with the originator, if present in
RteMsg.

RteMsg.TargSeqNum
The sequence number associated with the target, if present in
RteMsg.

RteMsg.MetricType
The metric type of the route requested.

RteMsg.Metric
The metric value received in the RteMsg.

RteMsg.Timestamp
The last time this entry was updated.

RteMsg.RemoveTime
The time at which this entry MUST be removed, MAX_SEQNUM_LIFETIME
after the last update of RteMsg.OrigSeqNum for an RREQ, or
RteMsg.TargSeqNum for an RREP.

The Multicast Route Message Table is maintained so that no two
entries have the same MessageType, OrigAddr, TargAddr, and
MetricType. See Section 6.8 for details on updating this table.






Perkins, et al. Expires April 12, 2016 [Page 14]

Internet-Draft AODVv2 October 2015


4.6. Route Table

All AODVv2 routers MUST maintain a route table. The route table
entry is a conceptual data structure. Implementations MAY use any
internal representation but MUST contain the following information:

Route.Address
An address, which, when combined with Route.PrefixLength,
describes the set of destination addresses this route includes.

Route.PrefixLength
The prefix length, in bits, associated with Route.Address.

Route.SeqNum
The sequence number associated with Route.Address, obtained from
the last route message that successfully updated this route.

Route.NextHop
The source IP address of the message advertising the route to
Route.Address, i.e. an IP address of the AODVv2 router used for
the next hop on the path toward Route.Address.

Route.NextHopInterface
The interface used to send IP packets toward Route.Address.

Route.LastUsed
The time this route was last used to forward an IP packet.

Route.LastSeqNumUpdate
The time the sequence number for this route was last updated.

Route.ExpirationTime
The time at which this route must be marked as Invalid.

Route.MetricType
The type of metric associated with this route.

Route.Metric
The cost of the route toward Route.Address expressed in units
consistent with Route.MetricType.

Route.State
The last known state (Active, Idle, Invalid, or Unconfirmed) of
the route.

Route.Precursors (optional feature)
A list of upstream neighbors using the route (see Section 10.2).




Perkins, et al. Expires April 12, 2016 [Page 15]

Internet-Draft AODVv2 October 2015


There are four possible states for an AODVv2 route:

Active
An Active route is in current use for forwarding IP packets.

Idle
An Idle route has not been used in the last ACTIVE_INTERVAL, but
can still be used for forwarding IP packets.

Invalid
An Invalid route cannot be used for forwarding IP packets.
Invalid routes have sequence number information, which allows
incoming information to be assessed for freshness.

Unconfirmed
An Unconfirmed route cannot be used for forwarding IP packets. It
is a route learned from a Route Request which has not yet been
confirmed as bidirectional.

Route state changes are detailed in Section 6.9.1.

An AODVv2 route MAY be offered for a limited time. In this case, the
route is referred to as a timed route. The length of time for which
the route is valid is referred to as validity time, and is included
in messages which advertise the route. The shortened validity time
is reflected in Route.ExpirationTime. If a route is not timed, the
ExpirationTime is INFINITY_TIME.

5. Metrics

Metrics measure a cost or quality associated with a route or a link,
e.g., latency, delay, financial cost, energy, etc. Metric values are
reported in route messages, where the goal is to determine a route
between OrigAddr and TargAddr. In Route Request messages, the metric
describes the cost of the route from OrigAddr (the router client) to
the router sending the Route Request. The receiving router
calculates the cost from OrigAddr to itself, combining the metric
value from the message with knowledge of the link cost from the
sender to the receiver, i.e., the incoming link cost. This updated
route cost is included when regenerating the Route Request message.
In Route Reply messages, the metric reflects the cost of the route
from TargAddr (the router client) to the router sending the Route
Reply. Routes to OrigAddr and TargAddr are installed at intermediate
routers for the purposes of forwarding a Route Reply message and
subsequent data traffic between OrigAddr and TargAddr. Assuming link
metrics are symmetric, the cost of the routes to OrigAddr and
TargAddr installed at each router will be correct.




Perkins, et al. Expires April 12, 2016 [Page 16]

Internet-Draft AODVv2 October 2015


AODVv2 enables the use of multiple metric types. Each route
discovery attempt indicates which metric type is requested for the
route. For each MetricType, AODVv2 requires:

o A MetricType number, to indicate the metric type of a route.
MetricType numbers allocated are detailed in Section 12.3.

o A maximum value, denoted MAX_METRIC[MetricType]. If the cost of a
route exceeds MAX_METRIC[MetricType], the route is ignored.
AODVv2 cannot store routes that cost more than
MAX_METRIC[MetricType].

o A function for incoming link cost, denoted Cost(L). Using
incoming link costs means that the route learned has a path
optimized for the direction from OrigAddr to TargAddr.

o A function for route cost, denoted Cost(R).

o A function to analyze routes for potential loops, denoted
LoopFree(R1, R2). LoopFree verifies that a route R2 is not a sub-
section of another route R1. An AODVv2 router invokes LoopFree()
as part of the process in Section 6.7.1, when an advertised route
(R1) and an existing route (R2) have the same destination address,
metric type, and sequence number. LoopFree returns FALSE to
indicate that an advertised route with higher cost is not to be
used to update a stored route. In the case where the existing
route is Invalid, it is possible that the advertised route
includes the existing route and came from a router which did not
yet receive notification of the route becoming Invalid, so the
advertised route should not be used in case it forms a loop to a
broken route.

AODVv2 currently supports cost metrics where Cost(R) is strictly
increasing, by defining:

o Cost(R) := Sum of Cost(L) of each link in the route

o LoopFree(R1, R2) := ( Cost(R1) <= Cost(R2) )

Implementers MAY consider other metric types, but the definitions of
Cost and LoopFree functions for such types are undefined, and
interoperability issues need to be considered.

6. AODVv2 Protocol Operations

The AODVv2 protocol's operations include managing sequence numbers,
monitoring adjacent AODVv2 routers, performing route discovery and
dealing with requests from other routers, processing incoming route



Perkins, et al. Expires April 12, 2016 [Page 17]

Internet-Draft AODVv2 October 2015


information and updating the route table, suppressing redundant
messages, maintaining the route table and reporting broken routes.
These processes are discussed in detail in the following sections.

6.1. Initialization

During initialization where an AODVv2 router does not have
information about its previous sequence number, or if its sequence
number is lost at any point, the router resets its sequence number to
one (1). However, other AODVv2 routers may still hold sequence
number information that this router previously issued. Since
sequence number information is removed if there has been no update to
the sequence number in MAX_SEQNUM_LIFETIME, the initializing router
must wait for MAX_SEQNUM_LIFETIME before it creates any messages
containing its new sequence number. It can then be sure that the
information it sends will not be considered stale.

Until MAX_SEQNUM_LIFETIME after its sequence number is reset, the
router SHOULD not create RREQ or RREP messages.

During this wait period, the router can do the following:

o Process information in a received RREQ or RREP message to learn a
route to the originator or target

o Send an RREP_Ack

o Regenerate a received RREQ or RREP

o Maintain valid routes in order that the forwarding process can
forward IP packets to Router Clients and to other routers

o Create, process and regenerate RERR messages

6.2. Adjacency Monitoring

AODVv2 routers MUST NOT establish routes over uni-directional links.
Consider the following. An RREQ is forwarded toward TargAddr, and
intermediate routers install a route to OrigAddr. If the link to the
next hop toward OrigAddr was uni-directional, and this route was used
to forward data traffic, the data packets would be lost. Further, an
RREP sent toward OrigAddr using this link will not reach the next
hop, and will therefore not be regenerated, and will never reach
RREQ_Gen, so end-to-end route establishment will fail. AODVv2
routers MUST verify that the link to the next hop is bidirectional
when establishing a route, and before allowing data traffic to be
forwarded on that route. If bidirectionality cannot be verified,
this link MUST be excluded from the route discovery procedure.



Perkins, et al. Expires April 12, 2016 [Page 18]

Internet-Draft AODVv2 October 2015


AODVv2 refers to a bidirectional link with a neighboring router as an
adjacency. AODVv2 routers do not need to monitor adjacency to all
neighbouring AODVv2 routers at all times, but MUST determine if there
is an adjacency to chosen next-hop AODVv2 routers during route
discovery.

o For the next hop toward OrigAddr, the approach for determining
bidirectional connectivity is to request acknowledgement of Route
Reply messages. Receipt of an acknowledgement proves that
bidirectional connectivity exists. All AODVv2 routers MUST
support this process, which is explained in Section 7.2 and
Section 7.3. If a link to a neighbor is determined to be
unidirectional because a requested acknowledgement is not received
within RREP_Ack_SENT_TIMEOUT, the neighbor MUST be blacklisted.

o For the next hop toward TargAddr, receipt of the Route Reply
message is confirmation of bidirectionality, since a Route Reply
message is a reply to a Route Request message which previously
crossed the link in the opposite direction.

To assist with adjacency monitoring, a Neighbor Table (Section 4.3)
is maintained. Each entry contains a neighbor IP address and an
indication of the state of the adjacency with that neighbor (Unknown,
Blacklisted, or Confirmed). When an RREQ or RREP is received from an
IP address which does not already have an entry in the Neighbor
Table, a new entry is created as discussed in Section 6.3. While
neighbor state is Unknown, acknowledgement of RREP messages MUST be
requested. While neighbor state is Confirmed, the request for an
acknowledgement is unnecessary.

When routers perform other operations such as those from the list
below, these MAY be used as additional indications of connectivity:

o NHDP HELLO Messages [RFC6130]

o Route timeout

o Lower layer triggers, e.g. message reception or link status
notifications

o TCP timeouts

o Promiscuous listening

o Other monitoring mechanisms or heuristics

If an external process signals that the link is bidirectional, the
neighbor state MAY be set to Confirmed. If an external process



Perkins, et al. Expires April 12, 2016 [Page 19]

Internet-Draft AODVv2 October 2015


signals that a link is not bidirectional, the AODVv2 router MAY
update the matching Neighbor Table entry by changing the neighbor
state to Blacklisted. If an external process signals that the link
might not be bidirectional, and the neighbor state is currently
Confirmed, the state MAY be set to Unknown.

For example, receipt of a Neighborhood Discovery Protocol HELLO
message with the receiving router listed as a neighbor is a signal of
bidirectional connectivity. The AODVv2 router MAY update the
matching Neighbor Table entry by changing the neighbor state to
Confirmed.

Similarly, if AODVv2 receives notification of a timeout, for example,
from TCP or some other protocol, this may be due to a disconnection.
The AODVv2 router MAY update the matching Neighbor Table entry by
resetting the neighbor state to Unknown.

6.3. Neighbor Table Update

On receipt of an RREQ or RREP message, the neighbor table MUST be
checked for an entry with Neighbor.IPAddress which matches the source
IP address of the message. If no matching entry is found, a new
entry is created.

A new Neighbor Table entry is created as follows:

o Neighbor.IPAddress := Source IP address of the message

o Neighbor.State := Unknown

o Neighbor.ResetTime := INFINITY_TIME

When the link to the neighbor is determined to be bidirectional, the
Neighbor Table entry is updated as follows:

o Neighbor.State := Confirmed

When the link to the neighbor is determined to be uni-directional,
the Neighbor Table entry is updated as follows:

o Neighbor.State := Blacklisted

o Neighbor.ResetTime := CurrentTime + MAX_BLACKLIST_TIME

When the Neighbor.ResetTime is reached, the Neighbor Table entry is
updated as follows:

o Neighbor.State := Unknown



Perkins, et al. Expires April 12, 2016 [Page 20]

Internet-Draft AODVv2 October 2015


When a link to a neighbor is determined to be broken, the Neighbor
Table entry SHOULD be removed.

Route requests from neighbors with Neighbor.State set to Blacklisted
are ignored to avoid persistent IP packet loss or protocol failures.
However, the reset time allows the neighbor to again be allowed to
participate in route discoveries after MAX_BLACKLIST_TIME, in case
the link between the routers has become bidirectional.

6.4. Interaction with Forwarding Plane

A reactive protocol reacts when a route is needed. A route is
requested when an application tries to send a packet. The
fundamental concept of reactive routing is to avoid creating routes
that are not needed.

AODVv2 requires signals from the forwarding plane:

o A packet cannot be forwarded because a route is unavailable:
AODVv2 needs to know the source and destination IP addresses of
the packet, to determine whether it should initiate route
discovery, including this information in a Route Request message,
or create a Route Error message.

o A packet is forwarded: AODVv2 needs to check the state of the
route. If the implementation uses timers to enforce route
timeouts, this signal is unnecessary.

o Packet forwarding failure occurs: AODVv2 initiates route error
reports.

o Packet forwarding succeeds: AODVv2 updates the record of when a
route was last used to forward a packet.

AODVv2 needs to send signals to the forwarding plane:

o A route discovery is in progress: packets awaiting a route may be
buffered while route discovery is attempted.

o A route discovery was not attempted: any buffered packets
requiring that route should be discarded.

o A route discovery failed: any buffered packets should be
discarded, and the source of the packet should be notified that
the destination is unreachable (using an ICMP Destination
Unreachable message).





Perkins, et al. Expires April 12, 2016 [Page 21]

Internet-Draft AODVv2 October 2015


o A route discovery succeeded: install a route which AODVv2 has
determined to be valid and begin transmitting any buffered
packets.

o A route has been lost: remove an installed route which AODVv2 has
determined to be invalid.

o A route has been updated: update an installed route when AODVv2
receives new information about the route.

These are conceptual signals, and can be implemented in various ways.
Conformant implementations of AODVv2 are not mandated to implement
the forwarding plane separately from the control plane or data plane;
these signals and interactions are identified simply as assistance
for implementers who may find them useful.

6.5. Message Transmission

AODVv2 sends [RFC5444] formatted messages using the parameters for
port number and IP protocol specified in [RFC5498]. Mapping of
AODVv2 data elements to [RFC5444] is detailed in Section 8.

Messages may travel a maximum of MAX_HOPCOUNT hops.

Unless otherwise specified, AODVv2 multicast messages are sent to the
link-local multicast address LL-MANET-Routers [RFC5498]. All AODVv2
routers MUST subscribe to LL-MANET-Routers [RFC5498] to receive
AODVv2 messages.

Note that multicast messages MAY be sent via unicast. For example,
this may occur for certain link-types (non-broadcast media), for
manually configured router adjacencies, or in order to improve
robustness.

Implementations MAY choose to employ techniques to reduce the number
of multicast messages sent. Use of [RFC6621] in deployments is
recommended. Employing [RFC6621] in a subset of the operational
AODVv2 routers in a network, or configuring different algorithms on
different routers, will not cause interoperability issues, but will
reduce the effectiveness of the multicast reduction scheme.

When multiple interfaces are available, an AODVv2 router transmitting
a multicast message to LL-MANET-Routers MUST send the message on all
interfaces that have been configured for AODVv2 operation, as given
in the AODVv2_INTERFACES list (Section 4.1). Similarly, AODVv2
routers MUST subscribe to LL-MANET-Routers on all their AODVv2
interfaces.




Perkins, et al. Expires April 12, 2016 [Page 22]

Internet-Draft AODVv2 October 2015


To avoid congestion, each AODVv2 router's rate of message generation
(CONTROL_TRAFFIC_LIMIT) SHOULD be limited and administratively
configurable. To prioritize transmission of AODVv2 control messages
in order to respect the CONTROL_TRAFFIC_LIMIT, RREP_Ack messages
SHOULD be given the highest priority. This allows learned routes to
be confirmed as bidirectional and avoids undesirable blacklisting of
next hop routers. Following RREP_Ack, RERR messages for
undeliverable IP packets SHOULD have second priority so that broken
routes that are still in use are reported, and IP packets are not
repeatedly forwarded to AODVv2
routers which cannot forward to their destination. RREP messages
SHOULD be given third priority in order that RREQs do not time out.
RREQ messages SHOULD be given priority over RERR messages for newly
invalidated routes, since the invalidated routes may not be in use,
and an RERR message will be generated if another router attempts to
use an Invalid route. RERR messages in response to RREP messages
which cannot be regenerated may be avoided since the RREP will not
reach OrigAddr, and the route request will be retried.

6.6. Route Discovery, Retries and Buffering

AODVv2's RREQ and RREP messages are used for route discovery. The
main difference between the two messages is that, by default, RREQ
messages are multicast to solicit an RREP, whereas RREP is unicast as
a response to the RREQ. The constants used in this section are
defined in Section 11.

When an AODVv2 router needs to forward an IP packet (with source
address OrigAddr and destination address TargAddr) from one of its
Router Clients, it needs a route to the packet's destination. If no
route exists, the AODVv2 router generates and multicasts a Route
Request message (RREQ) using OrigAddr and TargAddr. The procedure
for this is described in Section 7.1.1. The AODVv2 router is
referred to as RREQ_Gen.

IP packets awaiting a route MAY be buffered by RREQ_Gen. Buffering
of IP packets can have both positive and negative effects. Real-time
traffic, voice, and scheduled delivery may suffer if packets are
buffered and subjected to delays, but TCP connection establishment
will benefit if packets are queued while route discovery is
performed.

Determining which packets to discard first when the buffer is full is
a matter of policy at each AODVv2 router. Routers without sufficient
memory available for buffering SHOULD have buffering disabled. This
will affect the latency for launching TCP applications to new
destinations.




Perkins, et al. Expires April 12, 2016 [Page 23]

Internet-Draft AODVv2 October 2015


RREQ_Gen awaits reception of a Route Reply message (RREP) containing
a route toward TargAddr. A RREQ from TargAddr would also fulfil the
request, if adjacency to the next hop is already confirmed. If a
route to TargAddr is not learned within RREQ_WAIT_TIME, RREQ_Gen MAY
retry the route discovery. Each new RREQ results in an increment to
the sequence number. To reduce congestion in a network, repeated
attempts at route discovery for a particular target address SHOULD
utilize a binary exponential backoff. If the requested route is not
learned within RREQ_WAIT_TIME of sending the first RREQ, RREQ_Gen
sends a new RREQ. The wait time for the RREP corresponding to the
second RREQ is 2 * RREQ_WAIT_TIME. If the requested route is not
learned within this time period, another RREQ MAY be sent, up to a
total of DISCOVERY_ATTEMPTS_MAX. For each additional attempt, the
waiting time for the RREP is multiplied by 2, so that the time
conforms to a binary exponential backoff. This is the same technique
used in AODV [RFC3561].

The RREQ is received by neighboring AODVv2 routers, and processed and
regenerated as described in Section 7.1. Intermediate routers learn
a potential route to OrigAddr from the RREQ. The router responsible
for TargAddr responds by generating a Route Reply message (RREP) and
sends it back toward RREQ_Gen using the potential route to OrigAddr
learned from the RREQ. Each intermediate router regenerates the RREP
and unicasts toward OrigAddr.

Links which are not bidirectional cause problems. If a link is
unavailable in the direction toward OrigAddr, an RREP is not received
at the next hop, so cannot be regenerated, and it will never reach
RREQ_Gen. However, since routers monitor adjacencies (Section 6.2),
the loss of the RREP will cause the last router which regenerated the
RREP to blacklist the router which did not receive it. Later, a
timeout occurs at RREQ_Gen, and a new RREQ MAY be regenerated. If
the new RREQ arrives via the blacklisted router, it will be ignored,
enabling the RREQ to discover a different path toward TargAddr.

Route discovery SHOULD be considered to have failed after
DISCOVERY_ATTEMPTS_MAX and the corresponding wait time for an RREP
response to the final RREQ, in order to avoid generating control
traffic that is unlikely to discover a route. After the attempted
route discovery has failed, RREQ_Gen MUST wait at least
RREQ_HOLDDOWN_TIME before attempting another route discovery to the
same destination, to avoid generating more multicast messages which
are unlikely to discover a route. Any IP packets buffered for
TargAddr MUST also be dropped and a Destination Unreachable ICMP
message (Type 3) with a code of 1 (Host Unreachable Error) SHOULD be
delivered to the source of the packet, so that the application knows
about the failure. The source can be an application on RREQ_Gen
itself, or on a Router Client with address OrigAddr.



Perkins, et al. Expires April 12, 2016 [Page 24]

Internet-Draft AODVv2 October 2015


If RREQ_Gen does receive a route message containing a route to
TargAddr within the timeout, it MUST process the message according to
Section 7. When a valid route is installed, the router can begin
sending the buffered IP packets. Any retry timers for the
corresponding RREQ MUST be cancelled.

During route discovery, all routers on the path learn a route to both
OrigAddr and TargAddr, so that routes are constructed in both
directions. The route is optimized for the forward route, and the
return route uses the same path in reverse.

6.7. Processing Received Route Information

All AODVv2 route messages contain a route. A Route Request (RREQ)
includes a route to OrigAddr, and a Route Reply (RREP) contains a
route to TargAddr.

All AODVv2 routers that receive a route message can store the route
contained within it. Incoming information is first checked to verify
that it is both safe to use and offers an improvement to existing
information. This process is explained in Section 6.7.1. The route
table MAY then be updated according to Section 6.7.2.

In the processes below, RteMsg is used to denote the route message,
AdvRte is used to denote the route contained within it, and Route
denotes an existing route which matches AdvRte on address, prefix
length, and metric type.

AdvRte has the following properties:

o AdvRte.Address := RteMsg.OrigAddr (in RREQ) or RteMsg.TargAddr (in
RREP)

o AdvRte.PrefixLength := RteMsg.OrigPrefixLen (in RREQ) or
RteMsg.TargPrefixLen (in RREP) if included, or if no prefix length
was included in RteMsg, the address length, in bits, of
AdvRte.Address

o AdvRte.SeqNum := RteMsg.OrigSeqNum (in RREQ) or RteMsg.TargSeqNum
(in RREP)

o AdvRte.NextHop := RteMsg.IPSourceAddress (an address of the router
from which the AdvRte was received)

o AdvRte.MetricType := RteMsg.MetricType

o AdvRte.Metric := RteMsg.Metric




Perkins, et al. Expires April 12, 2016 [Page 25]

Internet-Draft AODVv2 October 2015


o AdvRte.Cost := Cost(R) using the cost function associated with the
route's metric type, where L is the link from the advertising
router, i.e. Cost(R) = AdvRte.Metric + Cost(L), as described in
Section 5.

o AdvRte.ValidityTime := RteMsg.ValidityTime, if included

6.7.1. Evaluating Route Information

Advertised routes are compared to existing routes to determine
whether the advertised route is to be used to update the routing
table. The incoming route information MUST be processed as follows:

1. Search for a route (Route) matching AdvRte's address, prefix
length and metric type

* If no matching route exists, AdvRte SHOULD be used to update
the routing table. Multiple routes to the same destination
may exist with different metric types.

* If all matching routing table entries have State set to
Unconfirmed, AdvRte SHOULD be added to the routing table.
This may result in multiple Unconfirmed routes to the same
address. In this case, the best route from the set of
Unconfirmed routes SHOULD be used to forward future RREPs. If
the link to the next hop is found to be bidirectional, and the
Unconfirmed route becomes valid, any remaining Unconfirmed
routes which would not offer improvement MUST be expunged.

* If a matching route exists with State set to Active, Idle, or
Invalid, continue to Step 2.

2. Compare sequence numbers using the technique described in
Section 4.4

* If AdvRte is more recent, AdvRte MUST be used to update the
routing table.

* If AdvRte is stale, AdvRte MUST NOT be used to update the
routing table.

* If the sequence numbers are equal, continue to Step 3.

3. Check that AdvRte is safe against routing loops (see Section 5)

* If LoopFree(AdvRte, Route) returns FALSE, AdvRte MUST NOT be
used to update the routing table because using the incoming
information might cause a routing loop.



Perkins, et al. Expires April 12, 2016 [Page 26]

Internet-Draft AODVv2 October 2015


* If LoopFree(AdvRte, Route) returns TRUE, continue to Step 3.

4. Compare route costs

* For some metric types, including the HopCount metric type
specified in Section 5, the best route is the route with the
lowest metric value. For other metric types, the best route
may be the route with the highest metric.

* If AdvRte is better, it SHOULD be used to update the routing
table because it offers improvement. If it is not used to
update the existing route, the existing non-optimal route will
continue to be used, causing data flows to use a route with
higher cost where this could have been avoided.

* If AdvRte is equal in cost and Route is Valid, AdvRte MAY be
used to update the routing table but will offer no
improvement.

* If AdvRte is worse and Route is valid, AdvRte MUST NOT be used
to update the routing table because it does not offer any
improvement.

* If AdvRte is not better (i.e., it is worse or equal) but Route
is Invalid, AdvRte SHOULD be used to update the routing table
because it can safely repair the existing Invalid route.

If the advertised route SHOULD be used to update the routing table,
the procedure in Section 6.7.2 MUST be followed. If the route is not
used, non-optimal routes will remain in the routing table.

6.7.2. Applying Route Updates

If AdvRte is from an RREQ message, the next hop neighbor may not be
confirmed as adjacent (see Section 4.3). If Neighbor.State is
Unknown, the route might not be viable, but it MUST be stored to
allow a corresponding RREP to be sent. However, Route.State will be
set to Unconfirmed to indicate that this route SHOULD NOT yet be used
to forward data, since the link may be uni-directional and packet
losses may occur. If a valid route already exists for this
destination, the Unconfirmed route SHOULD be stored as an additional
entry. If the link to the next hop is later confirmed to be
bidirectional, the route will offer improvement over the existing
valid route.

The route update is applied as follows:





Perkins, et al. Expires April 12, 2016 [Page 27]

Internet-Draft AODVv2 October 2015


1. If no existing route matches AdvRte on address, prefix length and
metric type, continue to Step 3 and create a new route.

2. If a matching route exists:

* If AdvRte.NextHop is not equal to Route.NextHop, and
AdvRte.NextHop's Neighbor.State is Unknown and Route.State is
Active or Idle, the current route is valid but the advertised
route may offer improvement, if the next hop can be confirmed
as bidirectional. Continue processing from Step 3 to create a
new route.

* If AdvRte.NextHop's Neighbor.State is Unknown and Route.State
is Invalid, continue processing from Step 4 to update the
existing route (Route).

* If AdvRte.NextHop's Neighbor.State is Confirmed, continue
processing from Step 4 to update the existing route.

3. Create a route and initialize as follows:

* Route.Address := AdvRte.Address

* Route.PrefixLength := AdvRte.PrefixLength

* Route.MetricType := AdvRte.MetricType

4. Update the route as follows:

* Route.SeqNum := AdvRte.SeqNum

* Route.NextHop := AdvRte.NextHop

* Route.NextHopInterface := interface on which RteMsg was
received

* Route.Metric := AdvRte.Cost

* Route.LastUsed := CurrentTime

* Route.LastSeqNumUpdate := CurrentTime

* Route.ExpirationTime := CurrentTime + AdvRte.ValidityTime if a
validity time exists, otherwise INFINITY_TIME

5. If a new route was created, or if the existing Route.State is
Invalid or Unconfirmed, update the route as follows:




Perkins, et al. Expires April 12, 2016 [Page 28]

Internet-Draft AODVv2 October 2015


* Route.State := Unconfirmed (if the next hop's Neighbor.State
is Unknown) or Idle

6. If an existing route changed from Invalid or Unconfirmed to
become Idle, any matching route table entries with worse metric
values SHOULD be expunged.

7. If this update results in a route with Route.State set to Active
or Idle, which matches an outstanding route request, the
associated route request retry timers can be cancelled and any
associated buffered IP packets MUST be forwarded.

6.8. Suppressing Redundant Messages Using the Multicast Route Message
Table

When route messages are flooded in a MANET, an AODVv2 router may
receive multiple similar messages. Regenerating every one of these
gives little additional benefit, and generates unnecessary signaling
traffic and interference.

Each AODVv2 router stores information about recently received route
messages in the AODVv2 Multicast Route Message Table (Section 4.5).

To create a Multicast Route Message Table Entry:

o RteMsg.MessageType := RREQ or RREP

o RteMsg.OrigAddr := OrigAddr from the message

o RteMsg.OrigPrefixLen := the prefix length associated with OrigAddr

o RteMsg.TargAddr := TargAddr from the message

o RteMsg.TargPrefixLen := the prefix length associated with TargAddr

o RteMsg.OrigSeqNum := the sequence number associated with OrigAddr,
if present in the message

o RteMsg.TargSeqNum := the sequence number associated with TargAddr,
if present in the message

o RteMsg.MetricType := the metric type of the route requested

o RteMsg.Metric := the metric value associated with OrigAddr in an
RREQ or TargAddr in an RREP

o RteMsg.Timestamp := CurrentTime




Perkins, et al. Expires April 12, 2016 [Page 29]

Internet-Draft AODVv2 October 2015


o RteMsg.RemoveTime := CurrentTime + MAX_SEQNUM_LIFETIME

Entries in the Multicast Route Message Table SHOULD be maintained for
at least RteMsg_ENTRY_TIME after the last Timestamp update in order
to account for long-lived RREQs traversing the network. An entry
MUST be deleted when the sequence number is no longer valid, i.e.,
after MAX_SEQNUM_LIFETIME. Memory-constrained devices MAY remove the
entry before this time.

To update a Multicast Route Message Table Entry, set:

o RteMsg.OrigSeqNum := the sequence number associated with OrigAddr,
if present in the message

o RteMsg.TargSeqNum := the sequence number associated with TargAddr,
if present in the message

o RteMsg.Metric := the metric value associated with OrigAddr in an
RREQ or TargAddr in an RREP

o RteMsg.Timestamp := CurrentTime

o RteMsg.RemoveTime := CurrentTime + MAX_SEQNUM_LIFETIME

Received route messages are tested against previously received route
messages, and if determined to be redundant, regeneration or response
can be avoided.

To determine if a received message is redundant:

1. Search for an entry in the Multicast Route Message Table with the
same MessageType, OrigAddr, TargAddr, and MetricType

* If there is none, the message is not redundant.

* If there is an entry, continue to Step 2.

2. Compare sequence numbers using the technique described in
Section 4.4

* For RREQ messages, use OrigSeqNum of the entry for comparison.
For RREP messages, use TargSeqNum of the entry for comparison.

* If the entry has an older sequence number than the received
message, the message is not redundant.

* If the entry has a newer sequence number than the received
message, the message is redundant.



Perkins, et al. Expires April 12, 2016 [Page 30]

Internet-Draft AODVv2 October 2015


* If the entry has the same sequence number, continue to Step 3.

3. Compare the metric values

* If the entry has a Metric value that is worse than or equal to
the metric in the received message, the message is redundant.

* If the entry has a Metric value that is better than the metric
in the received message, the message is not redundant.

If the message is redundant, update the timestamp on the entry, since
matching route messages are still traversing the network and this
entry should be maintained. This message should not be regenerated
or responded to.

If the message is not redundant, create an entry or update the
existing entry. Where the message is determined not redundant before
Step 3, it MUST be regenerated or responded to. Where the message is
determined not redundant in Step 3, it MAY be suppressed to avoid
extra control traffic. However, since the processing of the message
will result in an update to the route table, the message SHOULD be
regenerated or responded to, to ensure other routers have up-to-date
information and the best metrics. If not regenerated, the best route
may not be found. Where necessary, regeneration or response is
performed using the processes in Section 7.

6.9. Route Maintenance

Route maintenance involves monitoring and updating route state,
handling route timeouts and reporting routes that become Invalid.

Before using a route to forward an IP packet, an AODVv2 router MUST
check firstly if there is a route, and secondly the status of the
route (Section 6.9.1). If the route exists and is valid, it MUST be
marked as Active and its LastUsed timestamp MUST be updated, before
forwarding the IP packet to the route's next hop. If there is no
valid route, this MUST be reported to the packet's source (see
Section 6.9.2), or if the source address of the IP packet is a Router
Client, the RREQ generation procedure MUST be followed.

6.9.1. Route State

During normal operation, AODVv2 does not require any explicit
timeouts to manage the lifetime of a route. At any time, any route
MAY be examined and updated according to the rules below. If timers
are not used to prompt route state updates, route state MUST be
checked before IP packet forwarding and before any operation based on
route state.



Perkins, et al. Expires April 12, 2016 [Page 31]

Internet-Draft AODVv2 October 2015


The four possible states for an AODVv2 route are Active, Idle,
Invalid, and Unconfirmed:

Active
If Route.State is Active and the route is not timed (i.e., if
Route.ExpirationTime is INFINITY_TIME), Route.State MUST become
Idle if Route is not used to forward IP packets within
ACTIVE_INTERVAL. Route.State for a timed route (i.e.,
Route.ExpirationTime is not equal to INFINITY_TIME) remains Active
until its expiration time, after which it MUST become Invalid.

Idle
If Route.State is Idle, and the route is used to forward an IP
packet, Route.State MUST become Active. If the route is not used
to forward an IP packet within MAX_IDLETIME, Route.State MUST
become Invalid.

Invalid
If Route.State is Invalid, the route SHOULD be maintained until
MAX_SEQNUM_LIFETIME after Route.LastSeqNumUpdate, after which it
MUST be expunged. Route.SeqNum is used to classify future
information about Route.Address as stale or fresh.

Unconfirmed
If Route.State is Unconfirmed, the route MUST become Idle when an
adjacency with Route.NextHop is confirmed, or MUST be expunged if
the neighbor is blacklisted, or at MAX_SEQNUM_LIFETIME after
Route.LastSeqNumUpdate.

In all cases, if the time since Route.LastSeqNumUpdate exceeds
MAX_SEQNUM_LIFETIME, Route.SeqNum must be set to zero. This is
required to ensure that any AODVv2 routers following the
initialization procedure can safely begin routing functions using a
new sequence number, and that their messages will not be classified
as stale and ignored. A route with Route.State set to Active or Idle
can continue to be used to forward IP packets, but if Route.State
later becomes Invalid, the route MUST be expunged.

Appendix C.2.1 contains an algorithmic representation of this timeout
behavior.

Routes can become Invalid before a timeout occurs:

o If a link breaks, all routes using that link for Route.NextHop
MUST immediately have Route.State set to Invalid.






Perkins, et al. Expires April 12, 2016 [Page 32]

Internet-Draft AODVv2 October 2015


o If a Route Error (RERR) message containing the route is received
from Route.NextHop or if PktSource is set to a Router Client
address, Route.State MUST immediately be set to Invalid.

When Route.State changes from Unconfirmed to Idle as a result of the
adjacency with Route.NextHop being Confirmed (see Section 4.3), any
matching routes with metric values worse than Route.Metric MUST be
expunged.

Memory constrained devices MAY choose to expunge routes from the
AODVv2 route table before Route.ExpirationTime, but MUST adhere to
the following rules:

o An Active route MUST NOT be expunged, as this will result in
generation of a Route Error message followed by a necessary Route
Request to re-establish the route.

o An Idle route SHOULD NOT be expunged, as the route is still valid
for forwarding IP traffic, and if deleted, this could result in
dropped IP packets and a Route Request could be generated to re-
establish the route.

o Any Invalid route MAY be expunged; least recently used Invalid
routes SHOULD be expunged first, since these are less likely to be
reused.

o An Unconfirmed route MUST NOT be expunged if it was installed
within the last RREQ_WAIT_TIME, because it may correspond to a
route discovery in progress. A Route Reply message might be
received which needs to use the Route.NextHop information.
Otherwise, it MAY be expunged.

Route table entries are updated when Neighbor State is updated:

o While Neighbor.State is set to Unknown, any routes learned through
that neighbor are marked as Unconfirmed.

o When Neighbor.State is set to Confirmed, the Unconfirmed routes
using the neighbor as a next hop SHOULD be marked as valid (see
Section 6.9.1).

o When Neighbor.State is set to Blacklisted, any valid routes
installed which use that neighbor for their next hop are marked as
Invalid.

o When a Neighbor Table entry is removed, all routes using the
neighbor as next hop MUST be marked as Invalid.




Perkins, et al. Expires April 12, 2016 [Page 33]

Internet-Draft AODVv2 October 2015


6.9.2. Reporting Invalid Routes

When Route.State changes from Active to Invalid as a result of a
broken link or a received Route Error (RERR) message, other routers
SHOULD be informed by sending an RERR message containing details of
the invalidated route.

A RERR message SHOULD also be sent when an AODVv2 router receives an
IP packet to forward on behalf of another router but does not have a
valid route for the destination of the packet.

A RERR message SHOULD also be sent when an AODVv2 router receives an
RREP message to regenerate, but the route to the OrigAddr in the RREP
has been lost.

The packet or message triggering the RERR MUST be discarded.

Generation of an RERR message is described in Section 7.4.1.

7. AODVv2 Protocol Messages

AODVv2 defines four message types: Route Request (RREQ), Route Reply
(RREP), Route Reply Acknowledgement (RREP_Ack), and Route Error
(RERR).

Each AODVv2 message is defined as a set of data elements. Rules for
the generation, reception and regeneration of each message type are
described in the following sections. Section 8 discusses how the
data elements map to [RFC5444] Message TLVs, Address Blocks, and
Address TLVs.

7.1. Route Request (RREQ) Message

Route Request messages are used in route discovery operations to
request a route to a specified target address. RREQ messages have
the following contents:















Perkins, et al. Expires April 12, 2016 [Page 34]

Internet-Draft AODVv2 October 2015


+-----------------------------------------------------------------+
| msg_hop_limit, (optional) msg_hop_count |
+-----------------------------------------------------------------+
| AddressList |
+-----------------------------------------------------------------+
| PrefixLengthList (optional) |
+-----------------------------------------------------------------+
| OrigSeqNum, (optional) TargSeqNum |
+-----------------------------------------------------------------+
| MetricType |
+-----------------------------------------------------------------+
| OrigMetric |
+-----------------------------------------------------------------+
| ValidityTime (optional) |
+-----------------------------------------------------------------+

Figure 1: RREQ message contents

RREQ Data Elements

msg_hop_limit
The remaining number of hops allowed for dissemination of the RREQ
message.

msg_hop_count
The number of hops already traversed during dissemination of the
RREQ message.

AddressList
Contains OrigAddr and TargAddr, the source and destination
addresses of the IP packet for which a route is requested.
OrigAddr and TargAddr MUST be routable unicast addresses.

PrefixLengthList
Contains OrigPrefixLen, i.e., the length, in bits, of the prefix
associated with OrigAddr. If omitted, the prefix length is equal
to OrigAddr's address length in bits.

OrigSeqNum
The sequence number associated with OrigAddr.

TargSeqNum
A sequence number associated with TargAddr. This MAY be included
if an Invalid route exists to the target. This is useful for the
optional Intermediate RREP feature (see Section 10.3).

MetricType
The metric type associated with OrigMetric.



Perkins, et al. Expires April 12, 2016 [Page 35]

Internet-Draft AODVv2 October 2015


OrigMetric
The metric value associated with the route to OrigAddr, as
measured by the sender of the message.

ValidityTime
The length of time that the message sender is willing to offer a
route toward OrigAddr. Omitted if no time limit is imposed.

7.1.1. RREQ Generation

A RREQ is generated when an IP packet needs to be forwarded for a
Router Client, and no valid route currently exists for the packet's
destination.

Before creating an RREQ, the router SHOULD check if an RREQ has
recently been sent for the requested destination. If so, and the
wait time for a reply has not yet been reached, the router SHOULD
continue to await a response without generating a new RREQ. If the
timeout has been reached, a new RREQ MAY be generated. If buffering
is configured, the incoming IP packet SHOULD be buffered until the
route discovery is completed.

If the limit for the rate of AODVv2 control message generation has
been reached, no message SHOULD be generated.

To generate the RREQ, the router (referred to as RREQ_Gen) follows
this procedure:

1. Set msg_hop_limit := MAX_HOPCOUNT

2. Set msg_hop_count := 0, if including it

3. Set AddressList := {OrigAddr, TargAddr}

4. For the PrefixLengthList:

* If OrigAddr is part of an address range configured as a Router
Client, set PrefixLengthList := {OrigPrefixLen, null}.

* Otherwise, omit PrefixLengthList.

5. For OrigSeqNum:

* Increment the SeqNum associated with OrigAddr as specified in
Section 4.4.

* Set OrigSeqNum := SeqNum.




Perkins, et al. Expires April 12, 2016 [Page 36]

Internet-Draft AODVv2 October 2015


6. For TargSeqNum:

* If an Invalid route exists matching TargAddr using longest
prefix matching and has a valid sequence number, set
TargSeqNum := route's sequence number.

* If no Invalid route exists matching TargAddr, or the route
doesn't have a sequence number, omit TargSeqNum.

7. Include the MetricType data element and set the type accordingly

8. Set OrigMetric := Route[OrigAddr].Metric, i.e., RouterClient.Cost

9. Include the ValidityTime data element if advertising that the
route to OrigAddr via this router is offered for a limited time,
and set ValidityTime accordingly

This AODVv2 message is used to create a corresponding [RFC5444]
message (see Section 8) which is multicast, by default, to LL-MANET-
Routers on all interfaces configured for AODVv2 operation.

7.1.2. RREQ Reception

Upon receiving an RREQ, an AODVv2 router performs the following
steps:

1. If the sender is blacklisted (Section 4.3), check the entry's
reset time

* If CurrentTime < Remove Time, ignore this RREQ for further
processing.

* If CurrentTime >= Remove Time, reset the neighbor state to
Unknown and continue to Step 2.

2. Verify that the message hop count, if included, hasn't exceeded
MAX_HOPCOUNT

* If so, ignore this RREQ for further processing.

3. Verify that the message contains the required data elements:
msg_hop_limit, OrigAddr, TargAddr, OrigSeqNum, and OrigMetric,
and that OrigAddr and TargAddr are valid addresses (routable and
unicast)

* If not, ignore this RREQ for further processing.

4. Check that the MetricType is supported and configured for use



Perkins, et al. Expires April 12, 2016 [Page 37]

Internet-Draft AODVv2 October 2015


* If not, ignore this RREQ for further processing.

5. Verify that the cost of the advertised route will not exceed the
maximum allowed metric value for the metric type (Metric <=
MAX_METRIC[MetricType] - Cost(L))

* If it will, ignore this RREQ for further processing.

6. Process the route to OrigAddr as specified in Section 6.7.1

7. Check if the message is redundant by comparing to entries in the
Multicast Route Message table, following the procedure in
(Section 6.8)

* If redundant, ignore this RREQ for further processing.

* If not redundant, continue processing.

8. Check if the TargAddr belongs to one of the Router Clients

* If so, generate an RREP as specified in Section 7.2.1.

* If not, continue to RREQ regeneration.

7.1.3. RREQ Regeneration

By regenerating an RREQ, a router advertises that it will forward IP
packets to the OrigAddr contained in the RREQ according to the
information enclosed. The router MAY choose not to regenerate the
RREQ, though this could decrease connectivity in the network or
result in non-optimal paths. The full set of circumstances under
which a router might avoid regenerating an RREQ are not declared in
this document, though examples include the router being heavily
loaded or low on energy and therefore unwilling to advertise routing
capability for more traffic.

The RREQ SHOULD NOT be regenerated if the limit for the rate of
AODVv2 control message generation has been reached.

The procedure for RREQ regeneration is as follows:

1. Set msg_hop_limit := received msg_hop_limit - 1

2. If msg_hop_limit is now zero, do not continue the regeneration
process

3. Set msg_hop_count := received msg_hop_count + 1, if included,
otherwise omit msg_hop_count



Perkins, et al. Expires April 12, 2016 [Page 38]

Internet-Draft AODVv2 October 2015


4. Set AddressList, PrefixLengthList, sequence numbers and
MetricType to the values in the received RREQ

5. Set OrigMetric := Route[OrigAddr].Metric

6. If the received RREQ contains a ValidityTime, or if the
regenerating router wishes to limit the time that it offers a
route to OrigAddr, the regenerated RREQ MUST include a
ValidityTime data element

* The ValidityTime is either the ValidityTime the previous
AODVv2 router specified, or the ValidityTime this router
wishes to impose, whichever is lower.

This AODVv2 message is used to create a corresponding [RFC5444]
message (see Section 8) which is multicast, by default, to LL-MANET-
Routers on all interfaces configured for AODVv2 operation. However,
the regenerated RREQ can be unicast to the next hop address of the
route toward TargAddr, if known.

7.2. Route Reply (RREP) Message

A Route Reply message is sent in response to a Route Request message
and offers a route to the Target Address in the RREQ.

The RREP is sent by unicast to the next hop router on the route to
OrigAddr, if there is a Confirmed entry in the Neighbor Table for the
next hop. Otherwise, the RREP is sent multicast to LL-MANET-Routers,
including the AckReq data element in the message to indicate the
intended next hop address and request acknowledgement to confirm the
neighbor adjacency.

RREP messages have the following contents:


















Perkins, et al. Expires April 12, 2016 [Page 39]

Internet-Draft AODVv2 October 2015


+-----------------------------------------------------------------+
| msg_hop_limit, (optional) msg_hop_count |
+-----------------------------------------------------------------+
| AckReq (optional) |
+-----------------------------------------------------------------+
| AddressList |
+-----------------------------------------------------------------+
| PrefixLengthList (optional) |
+-----------------------------------------------------------------+
| TargSeqNum |
+-----------------------------------------------------------------+
| MetricType |
+-----------------------------------------------------------------+
| TargMetric |
+-----------------------------------------------------------------+
| ValidityTime (optional) |
+-----------------------------------------------------------------+

Figure 2: RREP message contents

RREP Data Elements

msg_hop_limit
The remaining number of hops allowed for dissemination of the RREP
message.

msg_hop_count
The number of hops already traversed during dissemination of the
RREP message.

AckReq
The address of the intended next hop of the RREP. This data
element is used when the RREP is multicast because the next hop
toward OrigAddr is a neighbor with Unknown state. It indicates
that an acknowledgement to the RREP is requested by the sender
from the intended next hop (see Section 6.2).

AddressList
Contains OrigAddr and TargAddr, the source and destination
addresses of the IP packet for which a route is requested.
OrigAddr and TargAddr MUST be routable unicast addresses.

PrefixLengthList
Contains TargPrefixLen, i.e., the length, in bits, of the prefix
associated with TargAddr. If omitted, the prefix length is equal
to TargAddr's address length, in bits.

TargSeqNum



Perkins, et al. Expires April 12, 2016 [Page 40]

Internet-Draft AODVv2 October 2015


The sequence number associated with TargAddr.

MetricType
The metric type associated with TargMetric.

TargMetric
The metric value associated with the route to TargAddr, as seen
from the sender of the message.

ValidityTime
The length of time that the message sender is willing to offer a
route toward TargAddr. Omitted if no time limit is imposed.

7.2.1. RREP Generation

A RREP is generated when an RREQ arrives requesting a route to one of
the AODVv2 router's Router Clients.

Before creating an RREP, the router SHOULD check if the corresponding
RREQ is redundant, i.e., a response has already been generated, or if
the limit for the rate of AODVv2 control message generation has been
reached. If so, the RREP SHOULD NOT be created.

If the next hop neighbor on the route to OrigAddr is not yet
confirmed as adjacent (as described in Section 6.2), the RREP MUST
include an AckReq data element including the intended next hop
address, in order to perform adjacency monitoring. If the adjacency
is already confirmed, it can be omitted. The AckReq data element
indicates that an acknowledgement to the RREP is requested from the
intended next hop router in the form of a Route Reply Acknowledgement
(RREP_Ack).

Implementations MAY allow a number of retries of the RREP if an
acknowledgement is not received within RREP_Ack_SENT_TIMEOUT,
doubling the timeout with each retry, up to a maximum of
RREP_RETRIES, using the same exponential backoff described in
Section 6.6 for RREQ retries. Adjacency confirmation MUST be
considered to have failed after the wait time for an RREP_Ack
response to the final RREP. The next hop router MUST be marked as
blacklisted (Section 4.3), and any installed routes with next hop set
to the newly blacklisted router SHOULD become Invalid.

To generate the RREP, the router (also referred to as RREP_Gen)
follows this procedure:

1. Set msg_hop_limit := msg_hop_count from the received RREQ
message, if it was included, or MAX_HOPCOUNT if it was not
included



Perkins, et al. Expires April 12, 2016 [Page 41]

Internet-Draft AODVv2 October 2015


2. Set msg_hop_count := 0, if including it

3. If adjacency with the next hop toward OrigAddr is not already
confirmed, include the AckReq data element with the address of
the intended next hop router

4. Set Address List := {OrigAddr, TargAddr}

5. For the PrefixLengthList:

* If TargAddr is part of an address range configured as a Router
Client, set PrefixLengthList := {null, TargPrefixLen}.

* Otherwise, omit PrefixLengthList.

6. For the TargSeqNum:

* Increment the SeqNum associated with TargAddr as specified in
Section 4.4.

* Set TargSeqNum := SeqNum.

7. Include the MetricType data element and set the type accordingly

8. Set TargMetric := Route[TargAddr].Metric, i.e., RouterClient.Cost

9. Include the ValidityTime data element if advertising that the
route to TargAddr via this router is offered for a limited time,
and set ValidityTime accordingly

This AODVv2 message is used to create a corresponding [RFC5444]
message (see Section 8). If there is a Confirmed entry in the
Neighbor Table for the next hop router on the route to OrigAddr, the
RREP is sent by unicast to the next hop. Otherwise, the RREP is sent
multicast to LL-MANET-Routers.

7.2.2. RREP Reception

Upon receiving an RREP, an AODVv2 router performs the following
steps:

1. If the sender is blacklisted (Section 4.3), but the RREP answers
a recently sent RREQ, the Neighbor Table entry for this sender
SHOULD have State set to Confirmed since an RREP is an
indication of adjacency

2. Verify that the message hop count, if included, hasn't exceeded
MAX_HOPCOUNT



Perkins, et al. Expires April 12, 2016 [Page 42]

Internet-Draft AODVv2 October 2015


* If so, ignore this RREQ for further processing.

3. Verify that the message contains the required data elements:
msg_hop_limit, OrigAddr, TargAddr, TargSeqNum, and TargMetric,
and that OrigAddr and TargAddr are valid addresses (routable and
unicast)

* If not, ignore this RREP for further processing.

4. Check that the MetricType is supported and configured for use

* If not, ignore this RREP for further processing.

5. Verify that the cost of the advertised route does not exceed the
maximum allowed metric value for the metric type (Metric <=
MAX_METRIC[MetricType] - Cost(L))

* If it does, ignore this RREP for further processing.

6. If the AckReq data element is present, check the intended
recipient of the received RREP

* If the receiving router is the intended recipient, send an
acknowledgement as specified in Section 7.3 and continue
processing.

* If the receiving router is not the intended recipient, ignore
this RREP for further processing.

7. Process the route to TargAddr as specified in Section 6.7.1

* If the route to TargAddr fulfills a previously sent RREQ, any
associated timeouts will be cancelled and buffered IP packets
will be forwarded to TargAddr, but processing continues to
Step 8.

8. Check if the message is redundant by comparing to entries in the
Multicast Route Message table (Section 6.8)

* If redundant, ignore this RREP for further processing.

* If not redundant, save the information in the Multicast Route
Message table to identify future redundant RREP messages and
continue processing.

9. Check if the OrigAddr belongs to one of the Router Clients

* If so, no further processing is necessary.



Perkins, et al. Expires April 12, 2016 [Page 43]

Internet-Draft AODVv2 October 2015


10. Check if a valid (Active or Idle) or Unconfirmed route exists to
OrigAddr

* If so, continue to RREP regeneration.

* If not, a Route Error message SHOULD be transmitted to
TargAddr according to Section 7.4.1 and the RREP SHOULD be
discarded and not regenerated.

7.2.3. RREP Regeneration

A received Route Reply message is regenerated toward OrigAddr.
Unless the router is prepared to advertise the route contained within
the received RREP, it halts processing. By regenerating a RREP, a
router advertises that it will forward IP packets to TargAddr
according to the information enclosed. The router MAY choose not to
regenerate the RREP, in the same way it MAY choose not to regenerate
an RREQ (see Section 7.1.3), though this could decrease connectivity
in the network or result in non-optimal paths.

The RREP SHOULD NOT be regenerated if the limit for the rate of
AODVv2 control message generation has been reached.

If the next hop neighbor on the route to OrigAddr is not yet
confirmed as adjacent (as described in Section 6.2), the RREP MUST
include an AckReq data element including the intended next hop
address, in order to perform adjacency monitoring. If the adjacency
is already confirmed, the AckReq data element can be omitted. The
AckReq data element indicates that an acknowledgement to the RREP is
requested in the form of a Route Reply Acknowledgement (RREP_Ack)
from the intended next hop router.

The procedure for RREP regeneration is as follows:

1. Set msg_hop_limit := received msg_hop_limit - 1

2. If msg_hop_limit is now zero, do not continue the regeneration
process

3. Set msg_hop_count := received msg_hop_count + 1, if it was
included, otherwise omit msg_hop_count

4. If an adjacency with the next hop toward OrigAddr is not already
confirmed, include the AckReq data element with the address of
the intended next hop router

5. Set AddressList, PrefixLengthList, TargSeqNum and MetricType to
the values in the received RREP



Perkins, et al. Expires April 12, 2016 [Page 44]

Internet-Draft AODVv2 October 2015


6. Set TargMetric := Route[TargAddr].Metric

7. If the received RREP contains a ValidityTime, or if the
regenerating router wishes to limit the time that it will offer a
route to TargAddr, the regenerated RREP MUST include a
ValidityTime data element

* The ValidityTime is either the ValidityTime the previous
AODVv2 router specified, or the ValidityTime this router
wishes to impose, whichever is lower.

This AODVv2 message is used to create a corresponding [RFC5444]
message (see Section 8). If there is a Confirmed entry in the
Neighbor Table for the next hop router on the route to OrigAddr, the
RREP is sent by unicast to the next hop. Otherwise, the RREP is sent
multicast to LL-MANET-Routers.

7.3. Route Reply Acknowledgement (RREP_Ack) Message

The Route Reply Acknowledgement MUST be sent in response to a
received Route Reply which includes an AckReq data element with an
address matching one of the receiving router's IP addresses. When
the RREP_Ack message is received, it confirms the adjacency between
the two routers. The RREP_Ack has no data elements.

7.3.1. RREP_Ack Generation

A RREP_Ack MUST be generated when a received RREP includes the AckReq
data element with the address of the receiving router. The RREP_Ack
SHOULD NOT be generated if the limit for the rate of AODVv2 control
message generation has been reached.

There are no data elements in an RREP_Ack. The [RFC5444]
representation is discussed in Section 8. The RREP_Ack is unicast,
by default, to the source IP address of the RREP message that
requested it.

7.3.2. RREP_Ack Reception

Upon receiving an RREP_Ack, an AODVv2 router performs the following
steps:

1. If an RREP_Ack message was expected from the IP source address of
the RREP_Ack, the router cancels any associated timeouts

2. If the RREP_Ack was expected, ensure the router sending the
RREP_Ack is marked with state Confirmed in the Neighbor
Table (Section 4.3)



Perkins, et al. Expires April 12, 2016 [Page 45]

Internet-Draft AODVv2 October 2015


7.4. Route Error (RERR) Message

A Route Error message is generated by an AODVv2 router to notify
other AODVv2 routers of routes that are no longer available. A RERR
message has the following contents:

+-----------------------------------------------------------------+
| msg_hop_limit |
+-----------------------------------------------------------------+
| PktSource (optional) |
+-----------------------------------------------------------------+
| AddressList |
+-----------------------------------------------------------------+
| PrefixLengthList (optional) |
+-----------------------------------------------------------------+
| SeqNumList (optional) |
+-----------------------------------------------------------------+
| MetricTypeList |
+-----------------------------------------------------------------+

Figure 3: RERR message contents

RERR Data Elements

msg_hop_limit
The remaining number of hops allowed for dissemination of the RERR
message.

PktSource
The source address of the IP packet triggering the RERR. If the
RERR is triggered by a broken link, the PktSource data element is
not required.

AddressList
The addresses of the routes no longer available through RERR_Gen.

PrefixLengthList
The prefix lengths, in bits, associated with the routes no longer
available through RERR_Gen, indicating whether a route represents
a single device or an address range.

SeqNumList
The sequence numbers of the routes no longer available through
RERR_Gen (where known).

MetricTypeList
The metric types associated with the routes no longer available
through RERR_Gen.



Perkins, et al. Expires April 12, 2016 [Page 46]

Internet-Draft AODVv2 October 2015


7.4.1. RERR Generation

A RERR is generated when an AODVv2 router (also referred to as
RERR_Gen) needs to report that a destination is no longer reachable.
There are two events that cause this response:

o If an IP packet arrives that cannot be forwarded because no valid
route exists for its destination, or if an RREP arrives which
cannot be regenerated because no route exists to OrigAddr, the
RERR generated MUST contain the PktSource data element and will
contain only one unreachable address. The contents of PktSource
and AddressList are set as follows:

* For an IP packet that cannot be forwarded, PktSource is set to
the source address of the IP packet, and the AddressList
contains the destination address of the IP packet.

* For an RREP message when the route to OrigAddr has been lost,
PktSource is set to the TargAddr of the RREP, and the
AddressList contains the OrigAddr from the RREP.

The prefix length and sequence number MAY be included if known
from an Invalid route entry to PktSource. The MetricTypeList MUST
also be included if a MetricType can be determined from the IP
packet or an existing Invalid route to PktSource.

RERR_Gen MUST discard the IP packet or RREP message that triggered
generation of the RERR.

In order to avoid flooding the network with RERR messages when a
stream of IP packets to an unreachable address arrives, an AODVv2
router SHOULD determine whether an RERR has recently been sent
with the same unreachable address and PktSource, and SHOULD avoid
creating duplicate RERR messages.

o When a link breaks, multiple routes may become Invalid, and the
RERR generated MAY contain multiple unreachable addresses. If the
message contents would cause the MTU to be exceeded, multiple RERR
messages must be sent. The RERR MUST include the MetricTypeList
data element. The PktSource data element is omitted.

All previously Active routes that used the broken link MUST be
reported. The AddressList, PrefixLengthList, SeqNumList, and
MetricTypeList will contain entries for each route which has
become Invalid.

A RERR message is only sent if an Active route becomes Invalid,
though an AODVv2 router can also include Idle routes that become



Perkins, et al. Expires April 12, 2016 [Page 47]

Internet-Draft AODVv2 October 2015


Invalid if the configuration parameter ENABLE_IDLE_IN_RERR is set
(see Section 11.3).

Incidentally, if an AODVv2 router receives an ICMP error packet to or
from the address of one of its Router Clients, it simply forwards the
ICMP packet in the same way as any other IP packet, and will not
generate any RERR message based on the contents of the ICMP packet.

The RERR SHOULD NOT be generated if the limit for the rate of AODVv2
control message generation has been reached.

To generate the RERR, the router follows this procedure:

1. Set msg_hop_limit := MAX_HOPCOUNT

2. If necessary, include the PktSource data element and set the
value to the source address of the IP packet triggering the RERR,
or the TargAddr of an RREP that cannot be regenerated toward
OrigAddr

3. For each route that needs to be reported, while respecting the
interface MTU:

* Insert the route address into the AddressList.

* Insert the prefix length into PrefixLengthList, if known and
not equal to the address length.

* Insert the sequence number into SeqNumList, if known.

* Insert the metric type into MetricTypeList.

4. If interface MTU would be exceeded, create additional RERR
messages

The AODVv2 message is used to create a corresponding [RFC5444]
message (see Section 8).

If the RERR is sent in response to an undeliverable IP packet or RREP
message, it SHOULD be sent unicast to the next hop on the route to
PktSource, or alternatively it MUST be multicast to LL-MANET-Routers.

If the RERR is sent in response to a broken link, the RERR is, by
default, multicast to LL-MANET-Routers.

If the optional precursor lists feature (see Section 10.2) is
enabled, the RERR is unicast to the precursors of the routes being
reported.



Perkins, et al. Expires April 12, 2016 [Page 48]

Internet-Draft AODVv2 October 2015


7.4.2. RERR Reception

Upon receiving an RERR, an AODVv2 router performs the following
steps:

1. Verify that the message contains the required data elements:
msg_hop_limit and at least one unreachable address

* If not, ignore this RREP for further processing.

2. For each address in the AddressList, check that:

* The address is valid (routable and unicast)

* The MetricType is supported and configured for use

* There is a valid route with the same MetricType matching the
address using longest prefix matching

* Either the route's next hop is the sender of the RERR and
route's next hop interface is the interface on which the RERR
was received, or PktSource is present in the RERR and is a
Router Client address

* The unreachable address' sequence number is either unknown, or
is greater than the route's sequence number

If any of the above are false, the route does not need to be made
Invalid and the unreachable address does not need to be
advertised in a regenerated RERR.

If all of the above are true:

* If the route's prefix length is the same as the unreachable
address' prefix length, set the route state to Invalid, and
note that the route SHOULD be advertised in a regenerated
RERR.

* If the prefix length is shorter than the original route, the
route MUST be expunged from the routing table, since it is a
sub-route of the larger route which is reported to be Invalid.

* If the prefix length is different, create a new route with the
unreachable address, and its prefix and sequence number, set
the state to Invalid, and note that the route SHOULD be
advertised in a regenerated RERR.





Perkins, et al. Expires April 12, 2016 [Page 49]

Internet-Draft AODVv2 October 2015


* Update the sequence number on the existing route, if the
reported sequence number is determined to be newer using the
comparison technique described in Section 4.4.

3. If PktSource is included and is a Router Client, do not
regenerate the RERR.

4. Check if there are unreachable addresses which need to be
advertised in a regenerated RERR

* If so, regenerate the RERR as detailed in Section 7.4.3.

* If not, take no further action.

7.4.3. RERR Regeneration

The RERR SHOULD NOT be generated if the limit for the rate of AODVv2
control message generation has been reached.

The procedure for RERR regeneration is as follows:

1. Set msg_hop_limit := received msg_hop_limit - 1

2. If msg_hop_limit is now zero, do not continue the regeneration
process

3. If the PktSource data element was included in the original RERR,
copy it into the regenerated RERR

4. For each route that needs to be reported, while respecting the
interface MTU:

* Insert the unreachable address into the AddressList.

* Insert the prefix length into PrefixLengthList, if known and
not equal to the address length.

* Insert the sequence number into SeqNumList, if known.

* Insert the MetricType into MetricTypeList.

5. If interface MTU would be exceeded, create additional RERR
messages

The AODVv2 message is used to create a corresponding [RFC5444]
message (see Section 8). If the RERR contains the PktSource data
element, the regenerated RERR SHOULD be sent unicast to the next hop
on the route to PktSource, or alternatively it MUST be multicast to



Perkins, et al. Expires April 12, 2016 [Page 50]

Internet-Draft AODVv2 October 2015


LL-MANET-Routers. If the RERR is sent in response to a broken link,
the RERR is, by default, multicast to LL-MANET-Routers.

8. RFC 5444 Representation

AODVv2 specifies that all control plane messages between routers
SHOULD use the Generalized Mobile Ad Hoc Network Packet/Message
Format [RFC5444], and therefore AODVv2 defines route messages
comprising data elements that map to message elements in [RFC5444].

[RFC5444] provides a multiplexed transport for multiple protocols.
An [RFC5444] multiplexer MAY choose to optimize the content of
certain message elements to reduce control plane overhead.

A brief summary of the [RFC5444] format:

1. A packet contains zero or more messages

2. A message contains a Message Header, one Message TLV Block, zero
or more Address Blocks, and one Address Block TLV Block per
Address Block

3. The Message TLV Block MAY contain zero or more Message TLVs

4. An Address Block TLV Block MAY include zero or more Address Block
TLVs

5. Each TLV value in an Address Block TLV Block can be associated
with all of the addresses, a contiguous set of addresses, or a
single address in the Address Block

AODVv2 does not require access to the [RFC5444] packet header.

In the message header, AODVv2 uses <msg-hop-limit>, <msg-hop-count>,
<msg-type> and <msg-addr-length>. <msg-addr-length> indicates the
length of any addresses in the message (using <msg-addr-length> :=
address length in octets - 1, i.e. 3 for IPv4 and 15 for IPv6).

Each address included in the Address Block is identified as OrigAddr,
TargAddr, PktSource, or Unreachable Address by including an
ADDRESS_TYPE TLV in the Address Block TLV Block.

The addresses in an Address Block MAY appear in any order, and values
in a TLV in the Address Block TLV Block must be associated with the
correct address in the Address Block. To indicate which value is
associated with each address, the AODVv2 message representation uses
lists where the order of the addresses in the AODVv2 AddressList data




Perkins, et al. Expires April 12, 2016 [Page 51]

Internet-Draft AODVv2 October 2015


element matches the order of values in other list-based data
elements, e.g., the order of SeqNums in the SeqNumList in an RERR.

The following sections show how AODVv2 data elements are represented
in [RFC5444] messages. AODVv2 defines a number of new TLVs and also
makes use of the VALIDITY_TIME TLV from [RFC5497]. See Section 12
for more information about the Message TLVs and Address Block TLVs
AODVv2 defines, and the type numbers allocated.

Where the extension type of a TLV is set to zero, this is the default
[RFC5444] value and the extension type will not be included in the
message.

8.1. RREQ

8.1.1. Message Header

+---------------+-----------------+---------------------------------+
| Data Element | Header Field | Value |
+---------------+-----------------+---------------------------------+
| None | <msg-type> | RREQ |
| msg_hop_limit | <msg-hop-limit> | MAX_HOPCOUNT |
| msg_hop_count | <msg-hop-count> | Number of hops traversed so far |
| | | by the message. |
+---------------+-----------------+---------------------------------+

8.1.2. Message TLV Block

A RREQ contains no Message TLVs.

8.1.3. Address Block

A RREQ contains two Addresses, OrigAddr and TargAddr, and each
address has an associated prefix length. If the prefix length has
not been included in the AODVv2 message, it is equal to the address
length in bits.

+-------------------------+------------------------------+
| Data Elements | Address Block |
+-------------------------+------------------------------+
| OrigAddr/OrigPrefixLen | <address> + <prefix-length> |
| TargAddr/TargPrefixLen | <address> + <prefix-length> |
+-------------------------+------------------------------+








Perkins, et al. Expires April 12, 2016 [Page 52]

Internet-Draft AODVv2 October 2015


8.1.4. Address Block TLV Block

Address Block TLVs are always associated with addresses in the
Address Block. The following sections show the TLVs that apply to
each address.

8.1.4.1. Address Block TLVs for OrigAddr

+--------------+---------------+------------+-----------------------+
| Data Element | TLV Type | Extension | Value |
| | | Type | |
+--------------+---------------+------------+-----------------------+
| None | ADDRESS_TYPE | 0 | ADDRTYPE_ORIGADDR |
| OrigSeqNum | SEQ_NUM | 0 | Sequence Number of |
| | | | RREQ_Gen, the router |
| | | | which initiated route |
| | | | discovery. |
| OrigMetric | PATH_METRIC | MetricType | Metric value for the |
| /MetricType | | | route to OrigAddr, |
| | | | using MetricType. |
| ValidityTime | VALIDITY_TIME | 0 | ValidityTime for |
| | | | route to OrigAddr. |
+--------------+---------------+------------+-----------------------+

8.1.4.2. Address Block TLVs for TargAddr

+------------+--------------+-------------+-------------------------+
| Data | TLV Type | Extension | Value |
| Element | | Type | |
+------------+--------------+-------------+-------------------------+
| None | ADDRESS_TYPE | 0 | ADDRTYPE_TARGADDR |
| TargSeqNum | SEQ_NUM | 0 | The last known |
| | | | TargSeqNum for |
| | | | TargAddr. |
+------------+--------------+-------------+-------------------------+

8.2. RREP

8.2.1. Message Header












Perkins, et al. Expires April 12, 2016 [Page 53]

Internet-Draft AODVv2 October 2015


+---------------+-----------------+---------------------------------+
| Data Element | Header Field | Value |
+---------------+-----------------+---------------------------------+
| None | <msg-type> | RREP |
| msg_hop_limit | <msg-hop-limit> | <msg-hop-count> from |
| | | corresponding RREQ. |
| msg_hop_count | <msg-hop-count> | Number of hops traversed so far |
| | | by the message. |
+---------------+-----------------+---------------------------------+

8.2.2. Message TLV Block

A RREP contains no Message TLVs.

8.2.3. Address Block

A RREP contains a minimum of two Addresses, OrigAddr and TargAddr,
and each address has an associated prefix length. If the prefix
length has not been included in the AODVv2 message, it is equal to
the address length in bits.

It MAY also contain the address of the intended next hop, in order to
request acknowledgement to confirm adjacency, as described in
Section 6.2. The prefix length associated with this address is equal
to the address length in bits.

+-------------------------+------------------------------+
| Data Elements | Address Block |
+-------------------------+------------------------------+
| OrigAddr/OrigPrefixLen | <address> + <prefix-length> |
| TargAddr/TargPrefixLen | <address> + <prefix-length> |
| AckReq | <address> + <prefix-length> |
+-------------------------+------------------------------+

8.2.4. Address Block TLV Block

Address Block TLVs are always associated with addresses in the
Address Block. The following sections show the TLVs that apply to
each address.

8.2.4.1. Address Block TLVs for OrigAddr

+-------------+---------------+----------------+--------------------+
| Data | TLV Type | Extension Type | Value |
| Element | | | |
+-------------+---------------+----------------+--------------------+
| None | ADDRESS_TYPE | 0 | ADDRTYPE_ORIGADDR |
+-------------+---------------+----------------+--------------------+



Perkins, et al. Expires April 12, 2016 [Page 54]

Internet-Draft AODVv2 October 2015


8.2.4.2. Address Block TLVs for TargAddr

+--------------+---------------+------------+-----------------------+
| Data Element | TLV Type | Extension | Value |
| | | Type | |
+--------------+---------------+------------+-----------------------+
| None | ADDRESS_TYPE | 0 | ADDRTYPE_TARGADDR |
| TargSeqNum | SEQ_NUM | 0 | Sequence number of |
| | | | RREP_Gen, the router |
| | | | which created the |
| | | | RREP. |
| TargMetric | PATH_METRIC | MetricType | Metric value for the |
| /MetricType | | | route to TargAddr, |
| | | | using MetricType. |
| ValidityTime | VALIDITY_TIME | 0 | ValidityTime for |
| | | | route to TargAddr. |
+--------------+---------------+------------+-----------------------+

8.2.4.3. Address Block TLVs for AckReq Intended Recipient Address

+--------------+---------------+-----------------+------------------+
| Data Element | TLV Type | Extension Type | Value |
+--------------+---------------+-----------------+------------------+
| None | ADDRESS_TYPE | 0 | ADDRTYPE_INTEND |
+--------------+---------------+-----------------+------------------+

8.3. RREP_Ack

8.3.1. Message Header

+---------------+---------------+-----------+
| Data Element | Header Field | Value |
+---------------+---------------+-----------+
| None | <msg-type> | RREP_Ack |
+---------------+---------------+-----------+

8.3.2. Message TLV Block

A RREP_Ack contains no Message TLVs.

8.3.3. Address Block

A RREP_Ack contains no Address Block.








Perkins, et al. Expires April 12, 2016 [Page 55]

Internet-Draft AODVv2 October 2015


8.3.4. Address Block TLV Block

A RREP_Ack contains no Address Block TLV Block.

8.4. RERR

8.4.1. Message Header

+----------------+------------------+---------------+
| Data Element | Header Field | Value |
+----------------+------------------+---------------+
| None | <msg-type> | RERR |
| msg_hop_limit | <msg-hop-limit> | MAX_HOPCOUNT |
+----------------+------------------+---------------+

8.4.2. Message TLV Block

A RERR contains no Message TLVs.

8.4.3. Address Block

The Address Block in an RERR MAY contain PktSource, the source
address of the IP packet triggering RERR generation, as detailed in
Section 7.4. Prefix Length associated with PktSource is equal to the
address length in bits.

Address Block always contains one Address per route that is no longer
valid, and each address has an associated prefix length. If a prefix
length has not been included for this address, it is equal to the
address length in bits.

+------------------------------+------------------------------------+
| Data Element | Address Block |
+------------------------------+------------------------------------+
| PktSource | <address> + <prefix-length> for |
| | PktSource |
| AddressList/PrefixLengthList | <address> + <prefix-length> for |
| | each unreachable address in |
| | AddressList |
+------------------------------+------------------------------------+

8.4.4. Address Block TLV Block

Address Block TLVs are always associated with addresses in the
Address Block. The following sections show the TLVs that apply to
each type of address in the RERR.





Perkins, et al. Expires April 12, 2016 [Page 56]

Internet-Draft AODVv2 October 2015


8.4.4.1. Address Block TLVs for PktSource

+--------------+---------------+---------------+--------------------+
| Data Element | TLV Type | Extension | Value |
| | | Type | |
+--------------+---------------+---------------+--------------------+
| PktSource | ADDRESS_TYPE | 0 | ADDRTYPE_PKTSOURCE |
+--------------+---------------+---------------+--------------------+

8.4.4.2. Address Block TLVs for Unreachable Addresses

+----------------+--------------+------------+----------------------+
| Data Element | TLV Type | Extension | Value |
| | | Type | |
+----------------+--------------+------------+----------------------+
| None | ADDRESS_TYPE | 0 | ADDRTYPE_UNREACHABLE |
| SeqNumList | SEQ_NUM | 0 | Sequence Number |
| | | | associated with |
| | | | invalid route to the |
| | | | unreachable address. |
| MetricTypeList | PATH_METRIC | MetricType | None. Extension Type |
| | | | set to MetricType of |
| | | | the route to the |
| | | | unreachable address. |
+----------------+--------------+------------+----------------------+

9. Simple External Network Attachment

Figure 4 shows a stub (i.e., non-transit) network of AODVv2 routers
which is attached to an external network via a single External
Network Access Router (abbreviated ENAR). The interface to the
external network MUST NOT be configured in the AODVv2_INTERFACES
list.

As in any externally-attached network, AODVv2 routers and clients
that wish to be reachable from hosts on the external network MUST
have IP addresses within the ENAR's routable and topologically
correct prefix (i.e., 191.0.2.0/24). This AODVv2 network and subnets
within it will be advertised to the external network using procedures
which are out of scope for this specification.











Perkins, et al. Expires April 12, 2016 [Page 57]

Internet-Draft AODVv2 October 2015


/-------------------------\
/ +----------------+ \
/ | AODVv2 Router | \
| | 191.0.2.2/32 | |
| +----------------+ | Routable
| +-----+--------+ Prefix
| | ENAR | /191.0.2.0/24
| | AODVv2 Router| /
| | 191.0.2.1 |/ /---------------\
| | serving net +------+ External \
| | 191.0.2.0/24 | \ Network /
| +-----+--------+ \---------------/
| +----------------+ |
| | AODVv2 Router | |
| | 191.0.2.3/32 | |
\ +----------------+ /
\ /
\-------------------------/

Figure 4: Simple External Network Attachment Example

When an AODVv2 router within the AODVv2 MANET wants to discover a
route toward an address on the external network, it uses the normal
AODVv2 route discovery for that IP Destination Address. The ENAR
MUST respond to RREQ on behalf of all external network destinations,
i.e., destinations not on the configured 191.0.2.0/24 subnet. RREQs
for addresses inside the AODVv2 network, i.e. destinations on the
configured 191.0.2.0/24 subnet, are handled using the standard
processes described in Section 7.

When an IP packet from an address on the external network destined
for an address in the AODVv2 MANET reaches the ENAR, if the ENAR does
not have a route toward that exact destination it will perform normal
AODVv2 route discovery for that destination.

Configuring the ENAR as a default router is outside the scope of this
specification.

10. Optional Features

A number of optional features for AODVv2, associated initially with
AODV, MAY be useful in networks with greater mobility or larger node
populations, or networks requiring reduced latency for application
launches. These features are not required by minimal
implementations.






Perkins, et al. Expires April 12, 2016 [Page 58]

Internet-Draft AODVv2 October 2015


10.1. Expanding Rings Multicast

For multicast RREQ, msg_hop_limit MAY be set in accordance with an
expanding ring search as described in [RFC3561] to limit the RREQ
propagation to a subset of the local network and possibly reduce
route discovery overhead.

10.2. Precursor Lists

This section specifies an interoperable enhancement to AODVv2
enabling more economical RERR notifications.

There can be several sources of traffic for a certain destination.
Each source of traffic and each upstream router between the
forwarding AODVv2 router and the traffic source is known as a
"precursor" for the destination. For each destination, an AODVv2
router MAY choose to keep track of precursors that have provided
traffic for that destination. Route Error messages about that
destination can be sent unicast to these precursors instead of
multicast to all AODVv2 routers.

Since an RERR will be regenerated if it comes from a next hop on a
valid route, the RERR SHOULD ideally be sent backwards along the
route that the source of the traffic uses, to ensure it is
regenerated at each hop and reaches the traffic source. If the
reverse path is unknown, the RERR SHOULD be sent toward the source
along some other route. Therefore, the options for saving precursor
information are as follows:

o Save the next hop on an existing route to the IP packet's source
address as the precursor. In this case, it is not guaranteed that
an RERR that is sent will follow the reverse of the source's
route. In rare situations, this may prevent the route from being
invalidated at the source of the data traffic.

o Save the IP packet's source address as the precursor. In this
case, the RERR can be sent along any existing route to the source
of the data traffic, and SHOULD include the PktSource data element
to ensure that the route will be invalidated at the source of the
traffic, in case the RERR does not follow the reverse of the
source's route.

o By inspecting the MAC address of each forwarded IP packet,
determine which router forwarded the packet, and save the router
address as a precursor. This ensures that when an RERR is sent to
the precursor router, the route will be invalidated at that
router, and the RERR will be regenerated toward the source of the
IP packet.



Perkins, et al. Expires April 12, 2016 [Page 59]

Internet-Draft AODVv2 October 2015


During normal operation, each AODVv2 router maintaining precursor
lists for a route must update the precursor list whenever it uses
this route to forward traffic to the destination. Precursors are
classified as Active if traffic has recently been forwarded by the
precursor. The precursor is marked with a timestamp to indicate the
time it last forwarded traffic on this route.

When an AODVv2 router detects that one or more routes are broken, it
MAY notify each Active precursor using a unicast Route Error message
instead of creating multicast traffic. Unicast is applicable when
there are few Active precursors compared to the number of neighboring
AODVv2 routers. However, the default multicast behavior is still
preferable when there are many precursors, since fewer message
transmissions are required.

When an AODVv2 router supporting precursor lists receives an RERR
message, it MAY identify the list of its own affected Active
precursors for the routes in the RERR, and choose to send a unicast
RERR to those, rather than send a multicast RERR.

When a route is expunged, any precursor list associated with it must
also be expunged.

10.3. Intermediate RREP

Without iRREP, only the AODVv2 router responsible for the target
address can respond to an RREQ. Using iRREP, route discoveries can
be faster and create less control traffic. This specification has
been published as a separate Internet Draft [I-D.perkins-irrep].

10.4. Message Aggregation Delay

The aggregation of multiple messages into a packet is specified in
[RFC5444].

Implementations MAY choose to briefly delay transmission of messages
for the purpose of aggregation (into a single packet) or to improve
performance by using jitter [RFC5148].

11. Configuration

AODVv2 uses various parameters which can be grouped into the
following categories:

o Timers

o Protocol constants




Perkins, et al. Expires April 12, 2016 [Page 60]

Internet-Draft AODVv2 October 2015


o Administrative parameters and controls

This section show the parameters along with their definitions and
default values (if any).

Note that several fields have limited size (bits or bytes). These
sizes and their encoding may place specific limitations on the values
that can be set.

11.1. Timers

AODVv2 requires certain timing information to be associated with
route table entries and message replies. The default values are as
follows:

+------------------------+----------------+
| Name | Default Value |
+------------------------+----------------+
| ACTIVE_INTERVAL | 5 second |
| MAX_IDLETIME | 200 seconds |
| MAX_BLACKLIST_TIME | 200 seconds |
| MAX_SEQNUM_LIFETIME | 300 seconds |
| RteMsg_ENTRY_TIME | 12 seconds |
| RREQ_WAIT_TIME | 2 seconds |
| RREP_Ack_SENT_TIMEOUT | 1 second |
| RREQ_HOLDDOWN_TIME | 10 seconds |
+------------------------+----------------+

Table 2: Timing Parameter Values

The above timing parameter values have worked well for small and
medium well-connected networks with moderate topology changes. The
timing parameters SHOULD be administratively configurable. Ideally,
for networks with frequent topology changes the AODVv2 parameters
SHOULD be adjusted using experimentally determined values or dynamic
adaptation. For example, in networks with infrequent topology
changes MAX_IDLETIME MAY be set to a much larger value.

If MAX_SEQNUM_LIFETIME was configured differently across the network,
and any of the routers lost their sequence number or rebooted, this
could result in their next route messages being classified as stale
at any AODVv2 router using a greater value for MAX_SEQNUM_LIFETIME.
This would delay route discovery from and to the re-initializing
router.







Perkins, et al. Expires April 12, 2016 [Page 61]

Internet-Draft AODVv2 October 2015


11.2. Protocol Constants

AODVv2 protocol constants typically do not require changes. The
following table lists these constants, along with their values and a
reference to the section describing their use.

+------------------------+---------+--------------------------------+
| Name | Default | Description |
+------------------------+---------+--------------------------------+
| DISCOVERY_ATTEMPTS_MAX | 3 | Section 6.6 |
| RREP_RETRIES | 2 | Section 7.2.1 |
| MAX_METRIC[MetricType] | [TBD] | Section 5 |
| MAX_METRIC[HopCount] | 20 hops | Section 5 and Section 7 |
| MAX_HOPCOUNT | 20 | Same as MAX_METRIC[HopCount] |
| INFINITY_TIME | [TBD] | Maximum expressible clock time |
| | | (Section 6.7.2) |
+------------------------+---------+--------------------------------+

Table 3: AODVv2 Constants

Note that <msg-hop-count> is an 8-bit field in the [RFC5444] message
header and therefore MAX_HOPCOUNT cannot be larger than 255. Field
lengths associated with metric values are found in Section 12.3.

MAX_METRIC[MetricType] MUST always be the maximum expressible metric
value of type MetricType.

These protocol constants MUST have the same values for all AODVv2
routers in the ad hoc network. If the values were configured
differently, the following consequences may be observed:

o DISCOVERY_ATTEMPTS_MAX: Routers with higher values are likely to
be more successful at finding routes, at the cost of additional
control traffic.

o RREP_RETRIES: Routers with lower values are more likely to
blacklist neighbors when there is a temporary fluctuation in link
quality.

o MAX_HOPCOUNT: Routers with a value too small would not be able to
discover routes to distant addresses.

o MAX_METRIC[MetricType]: No interoperability problems due to
variations on different routers, but routers with lower values may
exhibit overly restrictive behavior during route comparisons.






Perkins, et al. Expires April 12, 2016 [Page 62]

Internet-Draft AODVv2 October 2015


o INFINITY_TIME: No interoperability problems due to variations on
different routers, but if a lower value is used, route state
management may exhibit overly restrictive behavior.

11.3. Local Settings

The following table lists AODVv2 parameters which SHOULD be
administratively configured for each router:

+------------------------+------------------------+--------------+
| Name | Default Value | Description |
+------------------------+------------------------+--------------+
| AODVv2_INTERFACES | | Section 3 |
| BUFFER_SIZE_PACKETS | 2 | Section 6.6 |
| BUFFER_SIZE_BYTES | MAX_PACKET_SIZE [TBD] | Section 6.6 |
| CONTROL_TRAFFIC_LIMIT | [TBD - 50 pkts/sec?] | Section 7 |
+------------------------+------------------------+--------------+

Table 4: Configuration for Local Settings

11.4. Network-Wide Settings

The following administrative controls MAY be used to change the
operation of the network. The same settings SHOULD be used across
the network. Inconsistent settings at different routers in the
network will not result in protocol errors, but poor performance may
result.

+----------------------+-----------+----------------+
| Name | Default | Description |
+----------------------+-----------+----------------+
| ENABLE_IDLE_IN_RERR | Disabled | Section 7.4.1 |
+----------------------+-----------+----------------+

Table 5: Configuration for Network-Wide Settings

11.5. Optional Feature Settings

These options are not required for correct routing behavior, although
they may reduce AODVv2 protocol overhead in certain situations. The
default behavior is to leave these options disabled.










Perkins, et al. Expires April 12, 2016 [Page 63]

Internet-Draft AODVv2 October 2015


+---------------------------+-----------+---------------------------+
| Name | Default | Description |
+---------------------------+-----------+---------------------------+
| PRECURSOR_LISTS | Disabled | Local (Section 10.2) |
| MSG_AGGREGATION | Disabled | Local (Section 10.4) |
| ENABLE_IRREP | Disabled | Network-wide (Section |
| | | 10.3) |
| EXPANDING_RINGS_MULTICAST | Disabled | Network-wide (Section |
| | | 10.1) |
+---------------------------+-----------+---------------------------+

Table 6: Configuration for Optional Features

12. IANA Considerations

This section specifies several [RFC5444] message types and address
tlv-types required for AODVv2. A registry of metric types is
specified, in addition to a registry of address types.

12.1. RFC 5444 Message Types

This specification defines four Message Types, to be allocated from
the 0-223 range of the "Message Types" namespace defined in
[RFC5444], as specified in Table 7.

+-----------------------------------------+-----------+
| Name of Message | Type |
+-----------------------------------------+-----------+
| Route Request (RREQ) | 10 (TBD) |
| Route Reply (RREP) | 11 (TBD) |
| Route Error (RERR) | 12 (TBD) |
| Route Reply Acknowledgement (RREP_Ack) | 13 (TBD) |
+-----------------------------------------+-----------+

Table 7: AODVv2 Message Types

12.2. RFC 5444 Address Block TLV Types

This specification defines three Address Block TLV Types, to be
allocated from the "Address Block TLV Types" namespace defined in
[RFC5444], as specified in Table 8.










Perkins, et al. Expires April 12, 2016 [Page 64]

Internet-Draft AODVv2 October 2015


+------------------------+----------+---------------+---------------+
| Name of TLV | Type | Length | Reference |
| | | (octets) | |
+------------------------+----------+---------------+---------------+
| PATH_METRIC | 10 (TBD) | depends on | Section 7 |
| | | MetricType | |
| SEQ_NUM | 11 (TBD) | 2 | Section 7 |
| ADDRESS_TYPE | 15 (TBD) | 1 | Section 8 |
+------------------------+----------+---------------+---------------+

Table 8: AODVv2 Address Block TLV Types

12.3. MetricType Allocation

Note: This section does not require any IANA action since it refers
to metric types identified according to the assignments in [RFC6551].

+---------------------+----------+--------------------+
| Name of MetricType | Type | Metric Value Size |
+---------------------+----------+--------------------+
| Unassigned | 0 | Undefined |
| Hop Count | 3 [TBD] | 1 octet |
| Unallocated | 9 - 254 | TBD |
| Reserved | 255 | Undefined |
+---------------------+----------+--------------------+

Table 9: AODVv2 Metric Types

12.4. AddressType Allocation

Note: This section does not require any IANA action, as the required
information is included in the descriptions of the [RFC5444]
formatting in Section 8. The values used in the Address Type TLV are
given in the table below:

+-----------------------+--------+
| Address Type | Value |
+-----------------------+--------+
| ADDRTYPE_ORIGADDR | 0 |
| ADDRTYPE_TARGADDR | 1 |
| ADDRTYPE_UNREACHABLE | 2 |
| ADDRTYPE_PKTSOURCE | 3 |
| ADDRTYPE_INTEND | 4 |
| ADDRTYPE_UNSPECIFIED | 255 |
+-----------------------+--------+

Table 10: AODVv2 Address Types




Perkins, et al. Expires April 12, 2016 [Page 65]

Internet-Draft AODVv2 October 2015


13. Security Considerations

This section describes various security considerations and potential
avenues to secure AODVv2 routing. The objective of the AODVv2
protocol is for each router to communicate reachability information
about addresses for which it is responsible, and for routes it has
learned from other AODVv2 routers. Positive routing information
(i.e. a route exists) is distributed via RREQ and RREP messages.
Negative routing information (i.e. a route does not exist) is
distributed via RERR messages. AODVv2 routers store the information
contained in these messages in order to properly forward IP packets,
and they generally provide this information to other AODVv2 routers.

Networks using AODVv2 to maintain connectivity and establish routes
on demand may be vulnerable to certain well-known types of threats.
Flooding attacks using RREQ amount to a denial of service for route
discovery. Valid route table entries can be replaced by maliciously
constructed RREQ and RREP messages. Links could be erroneously
treated as bidirectional if malicious unsolicited RREP or RREP_Ack
messages were to be accepted. Replay attacks using RERR messages
could, in some circumstances, be used to disrupt active routes.
Passive inspection of AODVv2 control messages could enable
unauthorized devices to gain information about the network topology,
since exchanging such information is the main purpose of AODVv2.

The on-demand nature of AODVv2 route discovery reduces the
vulnerability to route disruption. Since control traffic for
updating route tables is diminished, there is less opportunity for
failure. Processing requirements for AODVv2 are typically quite
small, and would typically be dominated by calculations to verify
integrity. This has the effect of reducing (but by no means
eliminating) AODVv2's vulnerability to denial of service attacks.

Encryption MAY be used for AODVv2 messages. If the routers share a
packet-level security association, the message data can be encrypted
prior to message transmission. The establishment of such security
associations is outside the scope of this specification. Encryption
will not only protect against unauthorized devices obtaining
information about network topology but will ensure that only trusted
routers participate in routing operations.

Message integrity checking is enabled by the Integrity Check Value
mechanisms defined in [RFC7182]. The data contained in AODVv2
routing protocol messages SHOULD be verified using ICV values, to
avoid the use of message data if the message has been tampered with
or replayed. Otherwise, it would be possible to disrupt
communications by injecting nonexistent or malicious routes into the




Perkins, et al. Expires April 12, 2016 [Page 66]

Internet-Draft AODVv2 October 2015


route tables of routers within the ad hoc network. This can result
in loss of data or message processing by unauthorized devices.

The remainder of this section provides specific recommendations for
the use of the integrity checking and timestamp functions defined in
[RFC7182] to ensure the integrity of each AODVv2 message. The
calculation used for the Integrity Check Value will depend on the
message type. Sequence numbers can be used as timestamps to protect
against replay, since they are known to be strictly increasing.

RREQ messages advertise a route to OrigAddr, and impose very little
processing requirement for receivers. The main threat presented by
sending an RREQ message with false information is that traffic to
OrigAddr could be disrupted. Since RREQ is multicast and likely to
be received by all routers in the ad hoc network, this threat could
have serious impact on applications communicating by way of OrigAddr.
The actual threat to disrupt routes to OrigAddr is reduced by the
AODVv2 mechanism of marking RREQ-derived routes as "Unconfirmed"
until adjacency with the next hop is confirmed. If AODVv2 routers
always verify the integrity of the RREQ message data, then the threat
of disruption is minimized. The ICV mechanisms offered in [RFC7182]
are sufficient for this purpose. Since OrigAddr is included as a
data element of the RREQ, the ICV can be calculated and verified
using message contents. The ICV SHOULD be verified at every step
along the dispersal path of the RREQ to mitigate the threat. Since
RREQ_Gen's sequence number is incremented for each new RREQ, replay
protection is already afforded and no extra timestamp mechanism is
required.

RREP messages advertise a route to TargAddr, and impose very little
processing requirement for receivers. The main threat presented by
sending an RREP message with false information is that traffic to
TargAddr could be disrupted. Since RREP is unicast, this threat is
restricted to receivers along the path from OrigAddr to TargAddr. If
AODVv2 routers always verify the integrity of the RREP message data,
then this threat is minimized. This facility is offered by the ICV
mechanisms in [RFC7182]. Since TargAddr is included as a data
element of the RREP, the ICV can be calculated and verified using
message contents. The ICV SHOULD be verified at every step along the
unicast path of the RREP. Since RREP_Gen's sequence number is
incremented for each new RREP, replay protection is afforded and no
extra timestamp mechanism is required.

RREP_Ack messages are intended to verify bidirectional neighbor
connectivity, and impose very little processing requirement for
receivers. The main threat presented by sending an RREP_Ack message
with false information is that the route advertised to a target
address in an RREP might be erroneously accepted even though the



Perkins, et al. Expires April 12, 2016 [Page 67]

Internet-Draft AODVv2 October 2015


route would contain a unidirectional link and thus not be suitable
for most traffic. Since RREP_Ack is unicast, this threat is strictly
local to the RREP transmitter expecting the acknowledgement. A
malicious router could also attempt to send an unsolicited RREP_Ack
to convince another router that a bidirectional link exists and
subsequently use further messages to divert traffic along a route
which is not valid. If AODVv2 routers always verify the integrity of
the RREP_Ack message data, then this threat is minimized. This
facility is offered by the ICV mechanisms in [RFC7182]. The RREP_Gen
SHOULD use the source IP address of the RREP_Ack to identify the
sender, and so the ICV SHOULD be calculated using the message
contents and the IP source address. The message must also include
the Timestamp defined in [RFC7182] to protect against replay attacks,
using TargSeqNum from the RREP as the value in the TIMESTAMP TLV.

RERR messages remove routes, and impose very little processing
requirement for receivers. The main threat presented by sending an
RERR message with false information is that traffic to the advertised
destinations could be disrupted. Since RERR is multicast and can be
received by many routers in the ad hoc network, this threat could
have serious impact on applications communicating by way of the
sender of the RERR message. However, since the sender of the RERR
message with erroneous information MAY be presumed to be either
malicious or broken, it is better that such routes not be used
anyway. Another threat is that a malicious RERR message MAY be sent
with a PktSource data element included, to disrupt PktSource's
ability to send to the addresses contained in the RERR. If AODVv2
routers always verify the integrity of the RERR message data, then
this threat is reduced. This facility is offered by the ICV
mechanisms in [RFC7182]. The receiver of the RERR SHOULD use the
source IP address of the RERR to identify the sender. The message
must also include the Timestamp defined in [RFC7182] to protect
against replay attacks, using SeqNum from RERR_Gen as the value in
the TIMESTAMP TLV.

14. Acknowledgments

AODVv2 is a descendant of the design of previous MANET on-demand
protocols, especially AODV [RFC3561] and DSR [RFC4728]. Changes to
previous MANET on-demand protocols stem from research and
implementation experiences. Thanks to Elizabeth Belding and Ian
Chakeres for their long time authorship of AODV. Additional thanks
to Derek Atkins, Emmanuel Baccelli, Abdussalam Baryun, Ramon Caceres,
Thomas Clausen, Justin Dean, Christopher Dearlove, Ulrich Herberg,
Henner Jakob, Luke Klein-Berndt, Lars Kristensen, Tronje Krop,
Koojana Kuladinithi, Kedar Namjoshi, Keyur Patel, Alexandru Petrescu,
Henning Rogge, Fransisco Ros, Pedro Ruiz, Christoph Sommer, Romain
Thouvenin, Richard Trefler, Jiazi Yi, Seung Yi, and Cong Yuan, for



Perkins, et al. Expires April 12, 2016 [Page 68]

Internet-Draft AODVv2 October 2015


their reviews AODVv2 and DYMO, as well as numerous specification
suggestions.

15. References

15.1. Normative References

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/
RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.

[RFC3561] Perkins, C., Belding-Royer, E., and S. Das, "Ad hoc On-
Demand Distance Vector (AODV) Routing", RFC 3561, DOI
10.17487/RFC3561, July 2003,
<http://www.rfc-editor.org/info/rfc3561>.

[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, DOI 10.17487/RFC4291, February
2006, <http://www.rfc-editor.org/info/rfc4291>.

[RFC5082] Gill, V., Heasley, J., Meyer, D., Savola, P., Ed., and C.
Pignataro, "The Generalized TTL Security Mechanism
(GTSM)", RFC 5082, DOI 10.17487/RFC5082, October 2007,
<http://www.rfc-editor.org/info/rfc5082>.

[RFC5444] Clausen, T., Dearlove, C., Dean, J., and C. Adjih,
"Generalized Mobile Ad Hoc Network (MANET) Packet/Message
Format", RFC 5444, DOI 10.17487/RFC5444, February 2009,
<http://www.rfc-editor.org/info/rfc5444>.

[RFC5497] Clausen, T. and C. Dearlove, "Representing Multi-Value
Time in Mobile Ad Hoc Networks (MANETs)", RFC 5497, DOI
10.17487/RFC5497, March 2009,
<http://www.rfc-editor.org/info/rfc5497>.

[RFC5498] Chakeres, I., "IANA Allocations for Mobile Ad Hoc Network
(MANET) Protocols", RFC 5498, DOI 10.17487/RFC5498, March
2009, <http://www.rfc-editor.org/info/rfc5498>.

[RFC6551] Vasseur, JP., Ed., Kim, M., Ed., Pister, K., Dejean, N.,
and D. Barthel, "Routing Metrics Used for Path Calculation
in Low-Power and Lossy Networks", RFC 6551, DOI 10.17487/
RFC6551, March 2012,
<http://www.rfc-editor.org/info/rfc6551>.






Perkins, et al. Expires April 12, 2016 [Page 69]

Internet-Draft AODVv2 October 2015


[RFC7182] Herberg, U., Clausen, T., and C. Dearlove, "Integrity
Check Value and Timestamp TLV Definitions for Mobile Ad
Hoc Networks (MANETs)", RFC 7182, DOI 10.17487/RFC7182,
April 2014, <http://www.rfc-editor.org/info/rfc7182>.

15.2. Informative References

[I-D.perkins-irrep]
Perkins, C., "Intermediate RREP for dynamic MANET On-
demand (AODVv2) Routing", draft-perkins-irrep-03 (work in
progress), May 2015.

[Perkins94]
Perkins, C. and P. Bhagwat, "Highly Dynamic Destination-
Sequenced Distance-Vector Routing (DSDV) for Mobile
Computers", Proceedings of the ACM SIGCOMM '94 Conference
on Communications Architectures, Protocols and
Applications, London, UK, pp. 234-244, August 1994.

[Perkins99]
Perkins, C. and E. Royer, "Ad hoc On-Demand Distance
Vector (AODV) Routing", Proceedings of the 2nd IEEE
Workshop on Mobile Computing Systems and Applications, New
Orleans, LA, pp. 90-100, February 1999.

[RFC2501] Corson, S. and J. Macker, "Mobile Ad hoc Networking
(MANET): Routing Protocol Performance Issues and
Evaluation Considerations", RFC 2501, DOI 10.17487/
RFC2501, January 1999,
<http://www.rfc-editor.org/info/rfc2501>.

[RFC4193] Hinden, R. and B. Haberman, "Unique Local IPv6 Unicast
Addresses", RFC 4193, DOI 10.17487/RFC4193, October 2005,
<http://www.rfc-editor.org/info/rfc4193>.

[RFC4728] Johnson, D., Hu, Y., and D. Maltz, "The Dynamic Source
Routing Protocol (DSR) for Mobile Ad Hoc Networks for
IPv4", RFC 4728, DOI 10.17487/RFC4728, February 2007,
<http://www.rfc-editor.org/info/rfc4728>.

[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
DOI 10.17487/RFC4861, September 2007,
<http://www.rfc-editor.org/info/rfc4861>.







Perkins, et al. Expires April 12, 2016 [Page 70]

Internet-Draft AODVv2 October 2015


[RFC5148] Clausen, T., Dearlove, C., and B. Adamson, "Jitter
Considerations in Mobile Ad Hoc Networks (MANETs)", RFC
5148, DOI 10.17487/RFC5148, February 2008,
<http://www.rfc-editor.org/info/rfc5148>.

[RFC6130] Clausen, T., Dearlove, C., and J. Dean, "Mobile Ad Hoc
Network (MANET) Neighborhood Discovery Protocol (NHDP)",
RFC 6130, DOI 10.17487/RFC6130, April 2011,
<http://www.rfc-editor.org/info/rfc6130>.

[RFC6621] Macker, J., Ed., "Simplified Multicast Forwarding", RFC
6621, DOI 10.17487/RFC6621, May 2012,
<http://www.rfc-editor.org/info/rfc6621>.

[Sholander02]
Sholander, P., Coccoli, P., Oakes, T., and S. Swank, "A
Portable Software Implementation of a Hybrid MANET Routing
Protocol", 2002.

Appendix A. Multi-homing Considerations

Multi-homing is not supported by the AODVv2 specification. A Router
Client, i.e., an IP Address, can only be served by one AODVv2 router
at any time. The coordination between multiple AODVv2 routers to
distribute routing information correctly for a shared address is not
defined. See Appendix B for information about how to move a router
client to a different AODVv2 router.

Previous work indicates that it can be supported by expanding the
sequence number to include the AODVv2 router's IP address as a
parsable field of the SeqNum. Without this, comparing sequence
numbers would not work to evaluate freshness. Even when the IP
address is included, there is no good way to compare sequence numbers
from different IP addresses, but a handling node can determine
whether the two given sequence numbers are comparable. If the route
table can store multiple routes for the same destination, then multi-
homing can work with sequence numbers augmented by IP addresses.

This non-normative information is provided simply to document the
results of previous efforts to enable multi-homing. The intention is
to simplify the task of future specification if multihoming becomes
necessary for reactive protocol operation.

Appendix B. Router Client Relocation

Only one AODVv2 router within a MANET SHOULD be responsible for a
particular address at any time. If two AODVv2 routers dynamically
shift the advertisement of a network prefix, correct AODVv2 routing



Perkins, et al. Expires April 12, 2016 [Page 71]

Internet-Draft AODVv2 October 2015


behavior must be observed. The AODVv2 router adding the new network
prefix must wait for any existing routing information about this
network prefix to be purged from the network, i.e., it must wait at
least MAX_SEQNUM_LIFETIME after the previous AODVv2 router's last
SeqNum update for this network prefix.

Appendix C. Example Algorithms for AODVv2 Operations

The following subsections show example algorithms for protocol
operations required by AODVv2. AODVv2 requires general algorithms
for manipulating and comparing table entries, and algorithms specific
to each message type.

Processing for messages follows the following general outline:

1. Receive incoming message.

2. Update route table as appropriate.

3. Respond as needed, often regenerating the incoming message with
updated information.

Once the route table has been updated, the information contained
there is known to be the most recent available information for any
fields in the outgoing message. For this reason, the algorithms are
written as if outgoing message field values are assigned from the
route table information, even though it is often equally appropriate
to use fields from the incoming message.

The following table indicates the field names used in subsequent
sections to describe the AODVv2 algorithms.

+-------------------------+-----------------------------------------+
| Parameter | Description |
+-------------------------+-----------------------------------------+
| RteMsg | A route message |
| | (inRREQ/outRREQ/inRREP/outRREP) |
| RteMsg.HopLimit | Hop limit for the message |
| RteMsg.HopCount | Hop count for the message |
| RteMsg.AckReq | True/False, optional in RREP |
| RteMsg.MetricType | The type of metric included, optional |
| RteMsg.OrigAddr | Address of source of queued data |
| RteMsg.TargAddr | Address route is requested for |
| RteMsg.OrigPrefixLen | Prefix length of OrigAddr, optional |
| RteMsg.TargPrefixLen | Prefix length of TargAddr, optional |
| RteMsg.OrigSeqNum | SeqNum of OrigAddr, in RREQ only |
| RteMsg.TargSeqNum | SeqNum of TargAddr, in RREP, optional |
| | in RREQ |



Perkins, et al. Expires April 12, 2016 [Page 72]

Internet-Draft AODVv2 October 2015


| RteMsg.OrigMetric | Metric to OrigAddr, in RREQ only |
| RteMsg.TargMetric | Metric to TargAddr, in RREP only |
| RteMsg.ValidityTime | Time limit for route advertised |
| RteMsg.NbrIP | Sender of the RteMsg |
| RteMsg.Netif | Interface on which the RteMsg arrived |
| AdvRte | Derived from a RteMsg (see Section 6.7) |
| AdvRte.Address | Route destination address |
| AdvRte.PrefixLength | Route destination prefix length |
| AdvRte.SeqNum | SeqNum associated with route |
| AdvRte.MetricType | MetricType associated with route |
| AdvRte.Metric | Advertised metric of route |
| AdvRte.Cost | Cost from receiving router |
| AdvRte.ValidityTime | Time limit for route advertised |
| AdvRte.NextHopIP | Sender of the RteMsg |
| AdvRte.NextHopIntf | Interface on which the RteMsg arrived |
| AdvRte.HopCount | Number of hops traversed |
| AdvRte.HopLimit | Allowed number of hops remaining |
| Route | A route table entry (see Section 4.6) |
| Route.Address | Route destination address |
| Route.PrefixLength | Route destination prefix length |
| Route.SeqNum | SeqNum associated with route |
| Route.NextHop | Address of router which advertised the |
| | route |
| Route.NextHopInterface | Interface on which next hop is |
| | reachable |
| Route.LastUsed | Time this route was last used for |
| | packet forwarding |
| Route.LastSeqNumUpdate | Time the SeqNum of the route was last |
| | updated |
| Route.ExpirationTime | Time at which the route will expire |
| Route.MetricType | MetricType associated with route |
| Route.Metric | Cost from receiving router |
| Route.State | Active/Idle/Invalid |
| Route.Precursors | Optional (see Section 10.2) |
| RERR | Route Error message (inRERR/outRERR) |
| RERR.HopLimit | Hop limit for the message |
| RERR.PktSource | Source address of packet which |
| | triggered RERR |
| RERR.AddressList[] | List of unreachable route addresses |
| RERR.PrefixLengthList[] | List of PrefixLengths for AddressList |
| RERR.SeqNumList[] | List of SeqNums for AddressList |
| RERR.MetricTypeList[] | MetricType for the invalid routes |
| RERR.Netif | Interface on which the RERR arrived |
+-------------------------+-----------------------------------------+

Table 11: Notation used in Appendix





Perkins, et al. Expires April 12, 2016 [Page 73]

Internet-Draft AODVv2 October 2015


C.1. HopCount MetricType

The HopCount MetricType defines:

o MAX_METRIC[HopCount] := MAX_HOPCOUNT. A constant defined in
Section 11.2. MAX_HOPCOUNT is also used to limit the number of
hops an AODVv2 message can travel, regardless of the MetricType in
use. It MUST be larger than the AODVv2 network diameter, in order
that AODVv2 protocol messages may reach their intended
destinations.

o Cost(L) := 1

o Cost(R) := Sum of Cost(L) of each link in the route, i.e., the hop
count between the router calculating the cost, and the destination
of the route (OrigAddr if RREQ, TargAddr if RREP)

o LoopFree(R1, R2) := ( Cost(R1) <= Cost(R2) ). This is derived
from the fact that route cost increases with number of hops.
Therefore, an advertised route with higher cost than the
corresponding existing route could include the existing route as a
sub-section. Replacing the existing route with the advertised
route could form a routing loop.

C.2. General Operations

C.2.1. Check_Route_State
























Perkins, et al. Expires April 12, 2016 [Page 74]

Internet-Draft AODVv2 October 2015


/* Update the state of the route entry based on timeouts. Return
whether the route can be used for forwarding a packet. */

Check_Route_State(route)
{
if (CurrentTime > route.ExpirationTime)
route.State := Invalid;
if ((CurrentTime - route.LastUsed > ACTIVE_INTERVAL + MAX_IDLETIME)
AND (route.State != Unconfirmed)
AND (route.ExpirationTime == INFINITY_TIME)) //not a timed route
route.State := Invalid;
if ((CurrentTime - route.LastUsed > ACTIVE_INTERVAL)
AND (route.State != Unconfirmed)
AND (route.ExpirationTime == INFINITY_TIME)) //not a timed route
route.State := Idle;
if ((CurrentTime - route.LastSeqNumUpdate > MAX_SEQNUM_LIFETIME)
AND (route.State == Invalid OR route.State == Unconfirmed))
/* remove route from route table */
if ((CurrentTime - route.LastSeqNumUpdate > MAX_SEQNUM_LIFETIME)
AND (route.State != Invalid)
route.SeqNum := 0;

if (route still exists AND route.State != Invalid
AND Route.State != Unconfirmed)
return TRUE;
else
return FALSE;
}

C.2.2. Process_Routing_Info

(See Section 6.7.1)



















Perkins, et al. Expires April 12, 2016 [Page 75]

Internet-Draft AODVv2 October 2015


/* Compare incoming route information to stored route, and if better,
use to update stored route. */

Process_Routing_Info (advRte)
{
rte := Fetch_Route_Table_Entry (advRte);
if (!rte exists)
{
rte := Create_Route_Table_Entry(advRte);
return rte;
}

if (AdvRte.SeqNum > Route.SeqNum /* stored route is stale */
OR
(AdvRte.SeqNum == Route.SeqNum /* same SeqNum */
AND
((Route.State == Invalid AND LoopFree(advRte, rte))
/* advRte can repair stored */
OR AdvRte.Cost < Route.Metric))) /* advRte is better */
{
if (advRte is from a RREQ)
rte := Create_Route_Table_Entry(advRte);
else
Update_Route_Table_Entry (rte, advRte);
}
return rte;
}

C.2.3. Fetch_Route_Table_Entry






















Perkins, et al. Expires April 12, 2016 [Page 76]

Internet-Draft AODVv2 October 2015


/* Lookup a route table entry matching an advertised route */

Fetch_Route_Table_Entry (advRte)
{
foreach (rteTableEntry in rteTable)
{
if (rteTableEntry.Address == advRte.Address
AND rteTableEntry.MetricType == advRte.MetricType)
return rteTableEntry;
}
return null;
}

/* Lookup a route table entry matching address and metric type */

Fetch_Route_Table_Entry (destination, metricType)
{
foreach (rteTableEntry in rteTable)
{
if (rteTableEntry.Address == destination
AND rteTableEntry.MetricType == metricType)
return rteTableEntry;
}
return null;
}

C.2.4. Update_Route_Table_Entry

/* Update a route table entry using AdvRte in received RteMsg */

Update_Route_Table_Entry (rte, advRte);
{
rte.SeqNum := advRte.SeqNum;
rte.NextHop := advRte.NextHopIp;
rte.NextHopInterface := advRte.NextHopIntf;
rte.LastUsed := CurrentTime;
rte.LastSeqNumUpdate := CurrentTime;
if (validityTime)
rte.ExpirationTime := CurrentTime + advRte.ValidityTime;
else
rte.ExpirationTime := INFINITY_TIME;

rte.Metric := advRte.Cost;
if (rte.State == Invalid)
rte.State := Idle (if advRte is from RREP);
or Unconfirmed (if advRte is from RREQ);
}




Perkins, et al. Expires April 12, 2016 [Page 77]

Internet-Draft AODVv2 October 2015


C.2.5. Create_Route_Table_Entry

/* Create a route table entry from address and prefix length */

Create_Route_Table_Entry (address, prefixLength, seqNum, metricType)
{
rte := allocate_memory();
rte.Address := address;
rte.PrefixLength := prefixLength;
rte.SeqNum := seqNum;
rte.MetricType := metricType;
}


/* Create a route table entry from the advertised route */

Create_Route_Table_Entry(advRte)
{
rte := allocate_memory();

rte.Address := advRte.Address;
if (advRte.PrefixLength)
rte.PrefixLength := advRte.PrefixLength;
else
rte.PrefixLength := maxPrefixLenForAddressFamily;

rte.SeqNum := advRte.SeqNum;
rte.NextHop := advRte.NextHopIp;
rte.NextHopInterface := advRte.NextHopIntf;
rte.LastUsed := CurrentTime;
rte.LastSeqNumUpdate := CurrentTime;
if (validityTime)
rte.ExpirationTime := CurrentTime + advRte.ValidityTime;
else
rte.ExpirationTime := INFINITY_TIME;
rte.MetricType := advRte.MetricType;
rte.Metric := advRte.Metric;
rte.State := Idle (if advRte is from RREP);
or Unconfirmed (if advRte is from RREQ);
}

C.2.6. LoopFree









Perkins, et al. Expires April 12, 2016 [Page 78]

Internet-Draft AODVv2 October 2015


/* Return TRUE if the route advRte is LoopFree compared to rte */

LoopFree(advRte, rte)
{
if (advRte.Cost <= rte.Cost)
return TRUE;
else
return FALSE;
}

C.2.7. Fetch_Rte_Msg_Table_Entry

/* Find an entry in the RteMsg table matching the given
message's msg-type, OrigAddr, TargAddr, MetricType */

Fetch_Rte_Msg_Table_Entry (rteMsg)
{
foreach (entry in RteMsgTable)
{
if (entry.msg-type == rteMsg.msg-type
AND entry.OrigAddr == rteMsg.OrigAddr
AND entry.TargAddr == rteMsg.TargAddr
AND entry.MetricType == rteMsg.MetricType)
return entry;
}
return NULL;
}

C.2.8. Update_Rte_Msg_Table

(See Section 4.5)

/* Update the multicast route message suppression table based on the
received RteMsg, return true if it was created or the SeqNum was
updated (i.e. it needs to be regenerated) */

Update_Rte_Msg_Table(rteMsg)
{
/* search for a comparable entry */
entry := Fetch_Rte_Msg_Table_Entry(rteMsg);

/* if there is none, create one */
if (entry does not exist)
{
entry.MessageType := rteMsg.msg_type;
entry.OrigAddr := rteMsg.OrigAddr;
entry.TargAddr := rteMsg.TargAddr;
entry.OrigSeqNum := rteMsg.origSeqNum; // (if present)



Perkins, et al. Expires April 12, 2016 [Page 79]

Internet-Draft AODVv2 October 2015


entry.TargSeqNum := rteMsg.targSeqNum; // (if present)
entry.MetricType := rteMsg.MetricType;
entry.Metric := rteMsg.OrigMetric; // (for RREQ)
or rteMsg.TargMetric; // (for RREP)
entry.Timestamp := CurrentTime;
return TRUE;
}

/* if current entry is stale */
if (
(rteMsg.msg-type == RREQ AND entry.OrigSeqNum < rteMsg.OrigSeqNum)
OR
(rteMsg.msg-type == RREP AND entry.TargSeqNum < rteMsg.TargSeqNum))
{
entry.OrigSeqNum := rteMsg.OrigSeqNum; // (if present)
entry.TargSeqNum := rteMsg.TargSeqNum; // (if present)
entry.Timestamp := CurrentTime;
return TRUE;
}

/* if received rteMsg is stale */
if (
(rteMsg.msg-type == RREQ AND entry.OrigSeqNum > rteMsg.OrigSeqNum)
OR
(rteMsg.msg-type == RREP AND entry.TargSeqNum > rteMsg.TargSeqNum))
{
entry.Timestamp := CurrentTime;
return FALSE;
}

/* if same SeqNum but rteMsg has lower metric */
if (entry.Metric > rteMsg.Metric)
entry.Metric := rteMsg.Metric;

entry.Timestamp := CurrentTime;
return FALSE;
}

C.2.9. Build_RFC_5444_Message_Header












Perkins, et al. Expires April 12, 2016 [Page 80]

Internet-Draft AODVv2 October 2015


/* This pseudocode shows possible RFC 5444 actions, and would not
be performed by the AODVv2 implementation. It is shown only to
provide more understanding about the AODVv2 message that will be
constructed by RFC 5444.
MAL := Message Address Length
MF := Message Flags
Size := number of octets in MsgHdr, AddrBlk, AddrTLVs */

Build_RFC_5444_Message_Header (msgType, Flags, AddrFamily, Size,
hopLimit, hopCount, tlvLength)
{
/* Build RFC 5444 message header fields */
msg-type := msgType;
MF := Flags;
MAL := 3 or 15; // for IPv4 or IPv6
msg-size := Size;
msg-hop-limit := hopLimit;
if (hopCount != 0) /* if hopCount is 0, do not include */
msg-hop-count := hopCount;
msg.tlvs-length := tlvLength;
}

C.3. RREQ Operations

C.3.1. Generate_RREQ

/* Generate a route request message to find a route from OrigAddr
to TargAddr using the given MetricType
origAddr := IP address of Router Client which generated the
packet to be forwarded
origPrefix := prefix length associated with the Router Client
targAddr := destination IP address in the packet to be forwarded
targSeqNum := sequence number in existing route to targAddr
mType := metric type for the requested route */

Generate_RREQ(origAddr, origPrefix, targAddr, targSeqNum, mType)
{
/* Increment sequence number in nonvolatile storage */
mySeqNum := (1 + mySeqNum);

/* Marshall parameters */
outRREQ.HopLimit := MAX_HOPCOUNT;
outRREQ.HopCount := 0; // if included
outRREQ.MetricType := mType; //include if not DEFAULT_METRIC_TYPE
outRREQ.OrigAddr := origAddr;
outRREQ.TargAddr := targAddr;
outRREQ.OrigPrefixLen := origPrefix; //include if not address length
outRREQ.OrigSeqNum := mySeqNum;



Perkins, et al. Expires April 12, 2016 [Page 81]

Internet-Draft AODVv2 October 2015


outRREQ.TargSeqNum := targSeqNum; //included if available
outRREQ.OrigMetric := Route[OrigAddr].Metric; //zero by default
outRREQ.ValidityTime := limit for route to OrigAddr; //if required

/* Build Address Blk using prefix length information from
outRREQ.OrigPrefixLen if necessary */
AddrBlk := {outRREQ.OrigAddr, outRREQ.TargAddr};

/* Include sequence numbers in appropriate Address Block TLVs */
/* OrigSeqNum Address Block TLV */
origSeqNumAddrBlkTlv.value := outRREQ.OrigSeqNum;
/* TargSeqNum Address Block TLV */
if (outRREQ.TargSeqNum is known)
targSeqNumAddrBlkTlv.value := outRREQ.TargSeqNum;

/* Build Metric Address Block TLV, include Metric AddrBlkTlv
Extension type if a non-default metric */
metricAddrBlkTlv.value := outRREQ.OrigMetric;
if (outRREQ.MetricType != DEFAULT_METRIC_TYPE)
metricAddrBlkTlv.typeExtension := outRREQ.MetricType;

if (outRREQ.ValidityTime is required)
{
/* Build VALIDITY_TIME Address Block TLV */
VALIDITY_TIMEAddrBlkTlv.value := outRREQ.ValidityTime;
}

Build_RFC_5444_Message_Header (RREQ, 4, IPv4 or IPv6, NN,
outRREQ.HopLimit, outRREQ.HopCount, tlvLength);

/* multicast RFC 5444 message to LL-MANET-Routers */
}

C.3.2. Receive_RREQ

/* Process a RREQ received on link L */

Receive_RREQ (inRREQ, L)
{
if (inRREQ.NbrIP present in blacklist)
{
if (blacklist_expiration_time < CurrentTime)
return; // don't process or regenerate RREQ
else
remove nbrIP from blacklist;
}
if (inRREQ does not contain msg_hop_limit, OrigAddr,
TargAddr, OrigSeqNum, OrigMetric)



Perkins, et al. Expires April 12, 2016 [Page 82]

Internet-Draft AODVv2 October 2015


return;
if (msg_hop_count > MAX_HOPCOUNT)
return;
if (msg_hop_limit < 0)
return;
if (inRREQ.OrigAddr and inRREQ.TargAddr are not valid routable
and unicast addresses)
return;
if (inRREQ.MetricType is present but an unknown value)
return;
if (inRREQ.OrigMetric > MAX_METRIC[inRREQ.MetricType] - Cost(L))
return;

/* Extract inRREQ values */
advRte.Address := inRREQ.OrigAddr;
advRte.PrefixLength := inRREQ.OrigPrefixLen; (if present)
or the address length of advRte.Address;
advRte.SeqNum := inRREQ.OrigSeqNum;
advRte.MetricType := inRREQ.MetricType;
advRte.Metric := inRREQ.OrigMetric;
advRte.Cost := inRREQ.OrigMetric + Cost(L);
//according to the indicated MetricType
advRte.ValidityTime := inRREQ.ValidityTime; //if present
advRte.NextHopIP := inRREQ.NbrIP;
advRte.NextHopIntf := inRREQ.Netif;
advRte.HopCount := inRREQ.HopCount;
advRte.HopLimit := inRREQ.HopLimit;

rte := Process_Routing_Info (advRte);

/* Update the RteMsgTable and determine if the RREQ needs
to be regenerated */
regenerate := Update_Rte_Msg_Table(inRREQ);

if (inRREQ.TargAddr is in Router Client list)
Generate_RREP(inRREQ, rte);
else if (regenerate)
Regenerate_RREQ(inRREQ, rte);
}

C.3.3. Regenerate_RREQ

/* Called from receive_RREQ()
rte := the route to OrigAddr */

Regenerate_RREQ (inRREQ, rte)
{
outRREQ.HopLimit := inRREQ.HopLimit - 1;



Perkins, et al. Expires April 12, 2016 [Page 83]

Internet-Draft AODVv2 October 2015


if (outRREQ.HopLimit == 0)
return; // don't regenerate

if (inRREQ.HopCount exists)
{
if (inRREQ.HopCount >= MAX_HOPCOUNT)
return; // don't regenerate
outRREQ.HopCount := inRREQ.HopCount + 1;
}

/* Marshall parameters */
outRREQ.MetricType := rte.MetricType;
outRREQ.OrigAddr := rte.Address;
outRREQ.TargAddr := inRREQ.TargAddr;
/* include prefix length if not equal to address length */
outRREQ.OrigPrefixLen := rte.PrefixLength;
outRREQ.OrigSeqNum := rte.SeqNum;
outRREQ.TargSeqNum := inRREQ.TargSeqNum; // if present
outRREQ.OrigMetric := rte.Metric;
outRREQ.ValidityTime := rte.ValidityTime;
or the time limit this router wishes to put on
route to OrigAddr

/* Build Address Block using prefix length information from
outRREQ.OrigPrefixLen if necessary */
AddrBlk := {outRREQ.OrigAddr, outRREQ.TargAddr};

/* Include sequence numbers in appropriate Address Block TLVs */
/* OrigSeqNum Address Block TLV */
origSeqNumAddrBlkTlv.value := outRREQ.OrigSeqNum;
/* TargSeqNum Address Block TLV */
if (outRREQ.TargSeqNum is known)
targSeqNumAddrBlkTlv.value := outRREQ.TargSeqNum;

/* Build Metric Address Block TLV, include Metric AddrBlkTlv
Extension type if a non-default metric */
metricAddrBlkTlv.value := outRREQ.OrigMetric;
if (outRREQ.MetricType != DEFAULT_METRIC_TYPE)
metricAddrBlkTlv.typeExtension := outRREQ.MetricType;

if (outRREQ.ValidityTime is required)
{
/* Build VALIDITY_TIME Address Block TLV */
VALIDITY_TIMEAddrBlkTlv.value := outRREQ.ValidityTime;
}
Build_RFC_5444_Message_Header (RREQ, 4, IPv4 or IPv6, NN,
outRREQ.HopLimit, outRREQ.HopCount, tlvLength);




Perkins, et al. Expires April 12, 2016 [Page 84]

Internet-Draft AODVv2 October 2015


/* Multicast RFC 5444 message to LL-MANET-Routers, or if
inRREQ was unicast, the message can be unicast to the next
hop on the route to TargAddr, if known */
}

C.4. RREP Operations

C.4.1. Generate_RREP

Generate_RREP(inRREQ, rte)
{
/* Increment sequence number in nonvolatile storage */
mySeqNum := (1 + mySeqNum);

/* Marshall parameters */
outRREP.HopLimit := inRREQ.HopCount;
outRREP.HopCount := 0;
/* Include the AckReq when:
- previous RREP does not seem to enable any data flow, OR
- when RREQ is received from same OrigAddr after RREP was
unicast to rte.NextHop */
outRREP.AckReq := TRUE or FALSE; //TRUE if acknowledgement required
/* if included, set timeout RREP_Ack_SENT_TIMEOUT */

if (rte.MetricType != DEFAULT_METRIC_TYPE)
outRREP.MetricType := rte.MetricType;
outRREP.OrigAddr := inRREQ.Address;
outRREP.TargAddr := rte.TargAddr;
outRREP.TargPrefixLen := rte.PrefixLength; //if not address length
outRREP.TargSeqNum := mySeqNum;
outRREP.TargMetric := rte.Metric;
outRREP.ValidityTime := limit for route to TargAddr; //if required

if (outRREP.AckReq == TRUE)
/* include AckReq Message TLV */

/* Build Address Block using prefix length information from
outRREP.TargPrefixLen if necessary */
AddrBlk := {outRREP.OrigAddr, outRREP.TargAddr};

/* TargSeqNum Address Block TLV */
targSeqNumAddrBlkTlv.value := outRREP.TargSeqNum;

/* Build Metric Address Block TLV include Metric AddrBlkTlv
Extension type if a non-default metric */
metricAddrBlkTlv.value := outRREP.TargMetric;
if (outRREP.MetricType != DEFAULT_METRIC_TYPE)
metricAddrBlkTlv.typeExtension := outRREP.MetricType;



Perkins, et al. Expires April 12, 2016 [Page 85]

Internet-Draft AODVv2 October 2015


if (outRREP.ValidityTime is required)
{
/* Build VALIDITY_TIME Address Block TLV */
VALIDITY_TIMEAddrBlkTlv.value := outRREP.ValidityTime;
}

Build_RFC_5444_Message_Header (RREP, 4, IPv4 or IPv6, NN,
outRREP.HopLimit, outRREQ.HopCount, tlvLength);

/* unicast RFC 5444 message to rte[OrigAddr].NextHop */
}

C.4.2. Receive_RREP

/* Process a RREP received on link L */

Receive_RREP (inRREP, L)
{
if (inRREP.NbrIP present in blacklist)
{
if (blacklist_expiration_time < CurrentTime)
return; // don't process or regenerate RREP
else
remove NbrIP from blacklist;
}

if (inRREP does not contain msg_hop_limit, OrigAddr,
TargAddr, TargSeqNum, TargMetric)
return;
if (msg_hop_count > MAX_HOPCOUNT)
return;
if (msg_hop_limit < 0)
return;
if (inRREP.OrigAddr and inRREQ.TargAddr are not
valid routable and unicast addresses)
return;
if (inRREP.MetricType is present but an unknown value)
return;
if (inRREP.TargMetric > MAX_METRIC[inRREP.MetricType])
return;

/* Extract inRREP values */
advRte.Address := inRREP.TargAddr;
advRte.PrefixLength := inRREP.TargPrefixLen; //if present
or the address length of advRte.Address;
advRte.SeqNum := inRREP.TargSeqNum;
advRte.MetricType := inRREP.MetricType;
advRte.Metric := inRREP.TargMetric;



Perkins, et al. Expires April 12, 2016 [Page 86]

Internet-Draft AODVv2 October 2015


advRte.Cost := inRREP.TargMetric + Cost(L);
//according to the indicated MetricType
advRte.ValidityTime := inRREP.ValidityTime; //if present
advRte.NextHopIP := inRREP.NbrIP;
advRte.NextHopIntf := inRREP.Netif;
advRte.HopCount := inRREP.HopCount;
advRte.HopLimit := inRREP.HopLimit; //if included

rte := Process_Routing_Info (advRte);

` if (inRREP includes AckReq data element)
Generate_RREP_Ack(inRREP);

/* Update the RteMsgTable and determine if the RREP needs
to be regenerated */
regenerate := Update_Rte_Msg_Table(inRREP);

if (inRREP.TargAddr is in the Router Client list)
send_buffered_packets(rte); /* start to use the route */
else if (regenerate)
Regenerate_RREP(inRREP, rte);
}

C.4.3. Regenerate_RREP

Regenerate_RREP(inRREP, rte)
{
if (rte does not exist)
{
Generate_RERR(inRREP);
return;
}

outRREP.HopLimit := inRREP.HopLimit - 1;
if (outRREP.HopLimit == 0) /* don't regenerate */
return;

if (inRREP.HopCount exists)
{
if (inRREP.HopCount >= MAX_HOPCOUNT)
return; // don't regenerate the RREP
outRREP.HopCount := inRREP.HopCount + 1;
}

/* Marshall parameters */
/* Include the AckReq when:
- previous unicast RREP seems not to enable data flow, OR
- when RREQ is received from same OrigAddr after RREP



Perkins, et al. Expires April 12, 2016 [Page 87]

Internet-Draft AODVv2 October 2015


was unicast to rte.NextHop */
outRREP.AckReq := TRUE or FALSE; //TRUE if acknowledgement required
/* if included, set timeout RREP_Ack_SENT_TIMEOUT */

if (rte.MetricType != DEFAULT_METRIC_TYPE)
outRREP.MetricType := rte.MetricType;
outRREP.OrigAddr := inRREP.OrigAddr;
outRREP.TargAddr := rte.Address;
outRREP.TargPrefixLen := rte.PrefixLength; //if not address length
outRREP.TargSeqNum := rte.SeqNum;
outRREP.TargMetric := rte.Metric;
outRREP.ValidityTime := limit for route to TargAddr; //if required
outRREP.NextHop := rte.NextHop

if (outRREP.AckReq == TRUE)
/* include AckReq Message TLV */

/* Build Address Block using prefix length information from
outRREP.TargPrefixLen if necessary */
AddrBlk := {outRREP.OrigAddr, outRREP.TargAddr};

/* TargSeqNum Address Block TLV */
targSeqNumAddrBlkTlv.value := outRREP.TargSeqNum;

/* Build Metric Address Block TLV include Metric AddrBlkTlv
Extension type if a non-default metric */
metricAddrBlkTlv.value := outRREP.TargMetric;
if (outRREP.MetricType != DEFAULT_METRIC_TYPE)
metricAddrBlkTlv.typeExtension := outRREP.MetricType;

if (outRREP.ValidityTime is required)
{
/* Build VALIDITY_TIME Address Block TLV */
VALIDITY_TIMEAddrBlkTlv.value := outRREP.ValidityTime;
}

Build_RFC_5444_Message_Header (RREP, 4, IPv4 or IPv6, NN,
outRREP.HopLimit, 0, tlvLength);

/* unicast RFC 5444 message to rte[OrigAddr].NextHop */
}

C.5. RREP_Ack Operations








Perkins, et al. Expires April 12, 2016 [Page 88]

Internet-Draft AODVv2 October 2015


C.5.1. Generate_RREP_Ack

/* To be sent when a received RREP includes the AckReq data element */

Generate_RREP_Ack(inRREP)
{
Build_RFC_5444_Message_Header (RREP_Ack, 4, IPv4 or IPv6, NN,
1, 0, 0);
/* unicast RFC 5444 message to inRREP.NbrIP */
}

C.5.2. Receive_RREP_Ack

Receive_RREP_Ack(inRREP_Ack)
{
/* cancel timeout event for the node sending RREP_Ack */
}

C.5.3. Timeout_RREP_Ack

Timeout_RREP_Ack(outRREP)
{
if (numRetries < RREP_RETRIES)
/* resend RREP and double the previous timeout */
else
/* insert unresponsive node into blacklist */
}

C.6. RERR Operations

C.6.1. Generate_RERR

There are two parts to this function, based on whether it was
triggered by an undeliverable packet or a broken link to neighboring
AODVv2 router.

/* Generate a Route Error message.
errorType := undeliverablePacket or brokenLink */

Generate_RERR(errorType, triggerPkt, brokenLinkNbrIp)
{
switch (errorType)
{
case (brokenLink):
doGenerate := FALSE;
num-broken-addr := 0;
precursors[] := new empty precursor list;
outRERR.HopLimit := MAX_HOPCOUNT;



Perkins, et al. Expires April 12, 2016 [Page 89]

Internet-Draft AODVv2 October 2015


/* find routes which are now Invalid */
foreach (rte in route table)
{
if (brokenLinkNbrIp == rte.NextHop
AND (rte.State == Active
OR
(rte.State == Idle AND ENABLE_IDLE_IN_RERR)))
{
if (rte.State == Active)
doGenerate := TRUE;
rte.State := Invalid;
precursors += rte.Precursors (if any);
outRERR.AddressList[num-broken-addr] := rte.Address;
outRERR.PrefixLengthList[num-broken-addr] :=
rte.PrefixLength;
outRERR.SeqNumList[num-broken-addr] := rte.SeqNum;
outRERR.MetricTypeList[num-broken-addr] := rte.MetricType
num-broken-addr := num-broken-addr + 1;
}
}
}
case (undeliverablePacket):
doGenerate := TRUE;
num-broken-addr := 1;
outRERR.HopLimit := MAX_HOPCOUNT;
outRERR.PktSource := triggerPkt.SrcIP;
or triggerPkt.TargAddr; //if pkt was a RREP
outRERR.AddressList[0] := triggerPkt.DestIP;
or triggerPkt.OrigAddr; //if pkt was RREP
/* optional to include outRERR.PrefixLengthList, outRERR.SeqNumList
and outRERR.MetricTypeList */
}

if (doGenerate == FALSE)
return;

if (triggerPkt exists)
{
/* Build PktSource Message TLV */
pktSourceMessageTlv.value := outRERR.PktSource;
}

/* The remaining steps add address, prefix length, sequence
number and metric type information for each unreachable address,
while conforming to the allowed MTU. If the MTU is reached, a new
message MUST be created. */

/* Build Address Block using prefix length information from



Perkins, et al. Expires April 12, 2016 [Page 90]

Internet-Draft AODVv2 October 2015


outRERR.PrefixLengthList[] if necessary */
AddrBlk := outRERR.AddressList[];

/* Optionally, add SeqNum Address Block TLV, including index values */
seqNumAddrBlkTLV := outRERR.SeqNumList[];

if (outRERR.MetricTypeList contains non-default MetricTypes)
/* include Metric Address Block TLVs with Type Extension set to
MetricType, including index values if necessary */
metricAddrBlkTlv.typeExtension := outRERR.MetricTypeList[];

Build_RFC_5444_Message_Header (RERR, 4, IPv4 or IPv6, NN,
outRERR.HopLimit, 0, tlvLength);

if (undeliverablePacket)
/* unicast outRERR to rte[outRERR.PktSource].NextHop */
else if (brokenLink)
/* unicast to precursors, or multicast to LL-MANET-Routers */
}

C.6.2. Receive_RERR

Receive_RERR (inRERR)
{
if (inRERR does not contain msg_hop_limit and at least
one unreachable address)
return;

/* Extract inRERR values, copy relevant unreachable addresses,
their prefix lengths, and sequence numbers to outRERR */
num-broken-addr := 0;
precursors[] := new empty precursor list;
foreach (unreachableAddress in inRERR.AddressList)
{
if (unreachableAddress is not valid routable and unicast)
continue;
if (unreachableAddress MetricType is present but an unknown value)
return;

/* Find a matching route table entry, assume
DEFAULT_METRIC_TYPE if no MetricType included */
rte := Fetch_Route_Table_Entry (unreachableAddress,
unreachableAddress MetricType)
if (rte does not exist)
continue;
if (rte.State == Invalid)/* ignore already invalid routes */
continue;
if ((rte.NextHop != inRERR.NbrIP



Perkins, et al. Expires April 12, 2016 [Page 91]

Internet-Draft AODVv2 October 2015


OR
rte.NextHopInterface != inRERR.Netif)
AND (PktSource is not present OR is not a Router Client))
continue;
if (unreachableAddress SeqNum (if known) < rte.SeqNum)
continue;

/* keep a note of all precursors of newly Invalid routes */
precursors += rte.Precursors; //if any

/* assume prefix length is address length if not included */
if (rte.PrefixLength != unreachableAddress prefixLength)
{
/* create new route with unreachableAddress information */
invalidRte := Create_Route_Table_Entry(unreachableAddress,
unreachableAddress PrefixLength,
unreachableAddress SeqNum,
unreachableAddress MetricType);
invalidRte.State := Invalid;

if (rte.PrefixLength > unreachableAddress prefixLength)
expunge_route(rte);
rte := invalidRte;
}
else if (rte.PrefixLength == unreachableAddress prefixLength)
rte.State := Invalid;

outRERR.AddressList[num-broken-addr] := rte.Address;
outRERR.PrefixLengthList[num-broken-addr] := rte.PrefixLength;
outRERR.SeqNumList[num-broken-addr] := rte.SeqNum;
outRERR.MetricTypeList[num-broken-addr] := rte.MetricType;
num-broken-addr := num-broken-addr + 1;
}

if (num-broken-addr AND (PktSource is not present OR PktSource is not
a Router Client))
Regenerate_RERR(outRERR, inRERR, precursors);
}

C.6.3. Regenerate_RERR











Perkins, et al. Expires April 12, 2016 [Page 92]

Internet-Draft AODVv2 October 2015


Regenerate_RERR (outRERR, inRERR, precursors)
{
/* Marshal parameters */
outRERR.HopLimit := inRERR.HopLimit - 1;
if (outRERR.HopLimit == 0) // don't regenerate
return;

outRERR.PktSource := inRERR.PktSource; //if included
/* AddressList[], SeqNumList[], and PrefixLengthList[] are
already up-to-date */

if (outRERR.PktSource exists)
{
/* Build PktSource Message TLV */
pktSourceMessageTlv.value := outRERR.PktSource;
}

/* Build Address Block using prefix length information from
outRERR.PrefixLengthList[] if necessary */
AddrBlk := outRERR.AddressList[];

/* Optionally, add SeqNum Address Block TLV, including index values */
seqNumAddrBlkTLV := outRERR.SeqNumList[];

if (outRERR.MetricTypeList contains non-default MetricTypes)
/* include Metric Address Block TLVs with Type Extension set to
MetricType, including index values if necessary */
metricAddrBlkTlv.typeExtension := outRERR.MetricTypeList[];

Build_RFC_5444_Message_Header (RERR, 4, IPv4 or IPv6, NN,
outRERR.HopLimit, 0, tlvLength);

if (outRERR.PktSource exists)
/* unicast RFC 5444 message to next hop towards
outRERR.PktSource */
else if (number of precursors == 1)
/* unicast RFC 5444 message to precursors[0] */
else if (number of precursors > 1)
/* unicast RFC 5444 message to all precursors, or multicast
RFC 5444 message to RERR_PRECURSORS if preferable */
else
/* multicast RFC 5444 message to LL-MANET-Routers */
}








Perkins, et al. Expires April 12, 2016 [Page 93]

Internet-Draft AODVv2 October 2015


Appendix D. AODVv2 Draft Updates

D.1. Changes between revisions 11 and 12

This section lists the changes between AODVv2 revisions ...-11.txt
and ...-12.txt.

o Avoided use of "node" and "subnet" where possible.

o Improved separation of data structure information from protocol
operation.

o Updated uses of the terms "IP address" and "packet" to be clearer.

o More consistent and accurate use of MUST, SHOULD, SHOULD NOT, and
MAY, and added explanations of consequences of not implementing
SHOULDs.

o Used consistent references to [RFC5444].

o Updated title to include "Version 2".

o Updated Overview to state differences from AODV, text about loop
freedom and RFC 7182 in Overview.

o Updated Terminology and removed the Data Element table. Gave
clearer definition of Router Client and Unreachable Address.

o Updated Applicability Statement to draw attention to requirements
of the forwarding plane, handling of uni-directional links, usage
of IP addresses on multiple interfaces, and description of gateway
functionality. Added note about penalty for not storing
persistent state.

o Updated Router Client section and added cost to Router Client
entry.

o Clarified that Neighbor Table needs only information on
neighboring routers on discovered routes.

o Updated Sequence Number section. Use only one sequence number per
router. Added description of sequence number comparison.

o Updated descriptions of route states.

o Improved clarity of Metrics section, generic metric instead of
hopcount, removed default metric type, added explanation of
LoopFree.



Perkins, et al. Expires April 12, 2016 [Page 94]

Internet-Draft AODVv2 October 2015


o Improved Initialization section.

o Major update to Adjacency Monitoring section. Made it clear that
if bidirectional connectivity is already confirmed, requesting
acknowledgement is unnecessary. Separated Neighbor Table Updates
into separate section.

o Updated description of message prioritization near the control
message generation limit.

o Updated wording regarding [RFC6621].

o Added description of backoff used for message retries.

o Improved description of how unidirectional links are handled.

o Improved text regarding creation of Unconfirmed route entries.

o Improved section on determining redundancy of received multicast
messages.

o Added section on interactions with the forwarding plane.

o Improved Route State section. Clarified action when Active route
expires. Separated information on expunging routes on memory
constrained routers.

o Updated RERR description to be clearer about triggers.

o Updated IANA section to include only newly defined Messages and
TLVs, and define an Unspecified value for AddressType.

o Updated references.

o Updated section on Gateway behaviour.

o Updated Appendix D to include more checks on msg_hop_limit and
msg_hop_count.

o Renamed MAX_TIME to INFINITY_TIME to make meaning clearer.

D.2. Changes between revisions 10 and 11

This section lists the changes between AODVv2 revisions ...-10.txt
and ...-11.txt.

o Updated Simple Internet Attachment section to clarify behaviour of
IAR for incoming RREQ messages.



Perkins, et al. Expires April 12, 2016 [Page 95]

Internet-Draft AODVv2 October 2015


D.3. Changes between revisions 9 and 10

This section lists the changes between AODVv2 revisions ...-09.txt
and ...-10.txt.

o Updated [RFC5444] Representation section to add "Address Type"
TLV, which explicitly declares the meaning of addresses in the
[RFC5444] Address Block.

o Relocated route state definitions. Minor improvements to clarity
throughout.

o Updated definition of timed routes.

o More consistent use of OrigPrefixLen, TargPrefixLen, and Invalid.

o Mandated use of neighbor adjacency checking and support of AckReq
and RREP_Ack and clarified related text.

o Changed order of LoopFree checking and route cost comparisons in
Evaluating Route Information.

o Updated structure of section on Applying Route Updates.

o Updated AckReq to include intended next hop address, and RREP to
be multicast if intended next hop is not a confirmed neighbor.

o Clarified that gateway router is not default router.

D.4. Changes between revisions 8 and 9

This section lists the changes between AODVv2 revisions ...-08.txt
and ...-09.txt.

o Numerous editorial improvements were made, including
relocation/removal/renaming/adding of some sections and text,
collection and tidying of scattered text on same topic, formatting
made more consistent to improve readability.

o Removed mentions of precursors from main text, except one mention
in Route Table Entry.

o Removed use of MIN_METRIC which was not defined.

o Changed Current_Time to CurrentTime for consistency.

o Changed OrigAddrMetric and TargAddrMetric to OrigMetric and
TargMetric respectively.



Perkins, et al. Expires April 12, 2016 [Page 96]

Internet-Draft AODVv2 October 2015


o Updated Overview to simplify and provide a broader summary.

o Updated Terminology definitions, Data Elements tables and combined
sections.

o Updated Applicability Statement to move some of the non-
applicability text and to simplify what remains.

o Updated TLV names to conform to existing naming style.

o Updated Blacklist to be a NeighborList to include neighbors that
have confirmed bidirectional connectivity.

o Updated messages processed if router on blacklist and which are
indicators of bidirectional links.

o Added RemoveTime to RteMsg Table section.

o Added short description of timed route to Route Table Entry
section but removed Route.Timed flag. Route is timed if its
expiration time is not MAX_TIME.

o Added Unconfirmed route state for route to OrigAddr learned from
RREQ.

o Updated AODVv2 Protocol Operations section and subsections,
including Initialization, Adjacency Monitoring, making algorithms
easier to read and making notation consistent, general
improvements to the text.

o Updated Route Discovery, Retries and Buffering to include a more
complete description of the route discovery process.

o Updated wording relating to different metric types.

o Added text regarding control message limit in Message Transmission
section.

o Added short explanation of positive/negative effects of buffering.

o Simplified the packet diagrams, since some of their contents was
already explained in the text below and then again as part of
generation, reception and regeneration processes.

o Clarified some elements of the message content descriptions.

o Moved MetricType above MetricList in message sections, for
consistency.



Perkins, et al. Expires April 12, 2016 [Page 97]

Internet-Draft AODVv2 October 2015


o Mirrored structure throughout AODVv2 Protocol Messages.

o Changed RREQ and RREP's use of Lists when only one entry is
necessary.

o Added some pre-message-generation checks.

o Ensured consistency in regeneration (if msg-hop-limit is reduced
to zero, do not regenerate).

o Removed statements about neighbors but added blacklist checks
where necessary.

o Noted that RREQ retries SHOULD increase the SeqNum.

o Added statement that implementations SHOULD retry sending RREP.

o Added text explaining what happens if RREP is lost, regarding
blacklisting and RREQ retries.

o Removed hop limit from RREP_Ack. Changed order of blacklist
check.

o Updated RERR so that multiple metric types can be reported in the
same message.

o Updated RERR reception processing to ensure PktSource deletes the
contained route.

o Added text to show that if a router is the destination of a RERR,
the RERR is not regenerated.

o Added text that RERRs SHOULD NOT be created if the same RERR has
recently been sent.

o Updated [RFC5444] overview and simplified/rearranged text in this
section.

o Major update to [RFC5444] representation section

o Updated RERR's [RFC5444] representation so that PktSource is
placed in Address Block, and updated IANA section to make
PktSource an Address Block TLV to indicate which address is
PktSource.

o Described use of extension type in Metric TLV to represent
MetricType, and the interpretation when using the default metric
type.



Perkins, et al. Expires April 12, 2016 [Page 98]

Internet-Draft AODVv2 October 2015


o Removed Multicast RREP as an optional feature.

o Updated Precursor Lists section to include options for precursor
information to store.

o Updated Security Considerations.

D.5. Changes between revisions 7 and 8

This section lists the changes between AODVv2 revisions ...-07.txt
and ...-08.txt.

o MetricType is now an Address Block TLV. Minor changes to the
text. By using an extension type in the Metric TLV we can
represent MetricType more elegantly in the [RFC5444] message.

o Updated Overview to be slightly more concise.

o Moved MetricType next to Metric when mentioned for better flow.

o Added text to Applicability to address comments on mailing list
regarding gateway behavior and NHDP HELLO messages.

o Removed paragraph in AODVv2 Message Transmission section regarding
TTL.

o Added reference where precursors are mentioned in route table
entry.

o Added text to bidirectionality explanation regarding NHDP HELLO
messages and lower layer triggers.

o Clarified blacklist removal with SHOULD rather than MAY.

o Removed pseudo-code from section on evaluating incoming routing
information.

o Clarified rules for expunging route entries on memory-constrained
devices.

o Clarified the use of exponential backoff for route discovery
attempts.

o Small updates to message sections. Removed steps about checking
if neighbors.

o Renamed [RFC5444] parser to multiplexer in Section 10.




Perkins, et al. Expires April 12, 2016 [Page 99]

Internet-Draft AODVv2 October 2015


o Removed "optional feature" to include multiple addresses in RERR.

o Removed MetricType from the Message TLV Type Specification.

o Updated Security Considerations.

o Added reference to RFC 7182.

o Small updates to message algorithms, including moving MetricType
from Message TLV to the Metric TLV in the Address Block TLV Block,
and only generating RERR if an Active route was made Invalid.

D.6. Changes between revisions 6 and 7

This section lists the changes since AODVv2 revision ...-06.txt

o Added Victoria Mercieca as co-author.

o Reorganized protocol message descriptions into major subsections
for each protocol message. For protocol messages, organized
processing into Generation, Reception, and Regeneration
subsections.

o Separated RREQ and RREP message processing description into
separate major subsection which had previously been combined into
RteMsg description.

o Enlarged RREQ Table function to include similar processing for
optional flooded RREP messages. The table name has been
correspondingly been changed to be the Table for Multicast
RteMsgs.

o Moved sections for Multiple Interfaces and AODVv2 Control Message
Generation Limits to be major subsections of the AODVv2 Protocol
Operations section.

o Reorganized the protocol message processing steps into the
subsections as previously described, adopting a more step-by-step
presentation.

o Coalesced the router states Broken and Expired into a new combined
state named the Invalid state. No changes in processing are
required for this.

o Merged the sections describing Next-hop Router Adjacency
Monitoring and Blacklists.





Perkins, et al. Expires April 12, 2016 [Page 100]

Internet-Draft AODVv2 October 2015


o Specified that routes created during Route Discovery are marked as
Idle routes. If they are used for carrying data they become
Active routes.

o Added Route.LastSeqNumUpdate information to route table, so that
route activity and sequence number validity can be tracked
separately. An active route can still forward traffic even if the
sequence number has not been refreshed within MAX_SEQNUM_LIFETIME.

o Mandated implementation of RREP_Ack as response to AckReq Message
TLV in RREP messages.
Added field to RREP_Ack to ensure correspondence to the correct
AckReq message.

o Added explanations for what happens if protocol constants are
given different values on different AODVv2 routers.

o Specified that AODVv2 implementations are free to choose their own
heuristics for reducing multicast overhead, including RFC 6621.

o Added appendix to identify AODVv2 requirements from OS
implementation of IP and ICMP.

o Deleted appendix showing example [RFC5444] packet formats.

o Clarification on the use of RFC 5497 VALIDITY_TIME.

o In Terminology, deleted superfluous definitions, added missing
definitions.

o Numerous editorial improvements and clarifications.

D.7. Changes between revisions 5 and 6

This section lists the changes between AODVv2 revisions ...-05.txt
and ...-06.txt.

o Added Lotte Steenbrink as co-author.

o Reorganized section on Metrics to improve readability by putting
specific topics into subsections.

o Introduced concept of data element, which is used to clarify the
method of enabling [RFC5444] representation for AODVv2 data
elements. A list of Data Elements was introduced in section 3,
which provides a better understanding of their role than was
previously supplied by the table of notational devices.




Perkins, et al. Expires April 12, 2016 [Page 101]

Internet-Draft AODVv2 October 2015


o Replaced instances of OrigNode by OrigAddr whenever the more
specific meaning is appropriate. Similarly for instances of other
node versus address terminology.

o Introduced concepts of PrefixLengthList and MetricList in order to
avoid use of index-based terminology such as OrigNdx and TargNdx.

o Added section 5, "AODVv2 Message Transmission", describing the
intended interface to [RFC5444].

o Included within the main body of the specification the mandatory
setting of the TLV flag thassingleindex for TLVs OrigSeqNum and
TargSeqNum.

o Removed the Route.Timed state. Created a new flag for route table
entries known as Route.Timed. This flag can be set when the route
is in the active state. Previous description would require that
the route table entry be in two states at the same time, which
seems to be misleading. The new flag is used to clarify other
specification details for Timed routes.

o Created table 3 to show the correspondence between AODVv2 data
elements and [RFC5444] message components.

o Replaced "invalid" terminology by the more specific terms "broken"
or "expired" where appropriate.

o Eliminated the instance of duplicate specification for inclusion
of OrigNode (now, OrigAddr) in the message.

o Corrected the terminology to be Mid instead of Tail for the
trailing address bits of OrigAddr and TargAddr for the example
message formats in the appendices.

o Repaired remaining instances of phraseology that could be
construed as indicating that AODV only supports a single network
interface.

o Numerous editorial improvements and clarifications.

D.8. Changes between revisions 4 and 5

This section lists the changes between AODVv2 revisions ...-04.txt
and ...-05.txt.

o Normative text moved out of definitions into the relevant section
of the body of the specification.




Perkins, et al. Expires April 12, 2016 [Page 102]

Internet-Draft AODVv2 October 2015


o Editorial improvements and improvements to consistent terminology
were made. Replaced "retransmit" by the slightly more accurate
term "regenerate".

o Issues were resolved as discussed on the mailing list.

o Changed definition of LoopFree as suggested by Kedar Namjoshi and
Richard Trefler to avoid the failure condition that they have
described. In order to make understanding easier, replaced
abstract parameters R1 by RteMsg and R2 by Route to reduce the
level of abstraction when the function LoopFree is discussed.

o Added text to clarify that different metrics may have different
data types and different ranges of acceptable values.

o Added text to section "RteMsg Structure" to emphasize the proper
use of [RFC5444].

o Included within the main body of the specification the mandatory
setting of the TLV flag thassingleindex for TLVs OrigSeqNum and
TargSeqNum.

o Made more extensive use of the AdvRte terminology, in order to
better distinguish between the incoming RREQ or RREP message
(i.e., RteMsg) versus the route advertised by the RteMsg (i.e.,
AdvRte).

D.9. Changes between revisions 3 and 4

This section lists the changes between AODVv2 revisions ...-03.txt
and ...-04.txt.

o An appendix was added to exhibit algorithmic code for
implementation of AODVv2 functions.

o Numerous editorial improvements and improvements to consistent
terminology were made. Terminology related to prefix lengths was
made consistent. Some items listed in "Notational Conventions"
were no longer used, and so deleted.

o Issues were resolved as discussed on the mailing list.

o Appropriate instances of "may" were changed to "MAY".

o Definition inserted for "upstream".

o Route.Precursors included as an *optional* route table field




Perkins, et al. Expires April 12, 2016 [Page 103]

Internet-Draft AODVv2 October 2015


o Reworded text to avoid use of "relevant".

o Deleted references to "DestOnly" flag.

o Refined statements about MetricType TLV to allow for omission when
MetricType == HopCount.

o Bulletized list in section 8.1

o ENABLE_IDLE_UNREACHABLE renamed to be ENABLE_IDLE_IN_RERR

o Transmission and subscription to LL-MANET-Routers converted to
MUST from SHOULD.

D.10. Changes between revisions 2 and 3

This section lists the changes between AODVv2 revisions ...-02.txt
and ...-03.txt.

o The "Added Node" feature was removed. This feature was intended
to enable additional routing information to be carried within a
RREQ or a RREP message, thus increasing the amount of topological
information available to nodes along a routing path. However,
enlarging the packet size to include information which might never
be used can increase congestion of the wireless medium. The
feature can be included as an optional feature at a later date
when better algorithms are understood for determining when the
inclusion of additional routing information might be worthwhile.

o Numerous editorial improvements and improvements to consistent
terminology were made. Instances of OrigNodeNdx and TargNodeNdx
were replaced by OrigNdx and TargNdx, to be consistent with the
terminology shown in Table 1.

o Example RREQ and RREP message formats shown in the Appendices were
changed to use OrigSeqNum and TargSeqNum message TLVs instead of
using the SeqNum message TLV.

o Inclusion of the OrigNode's SeqNum in the RREP message is not
specified. The processing rules for the OrigNode's SeqNum were
incompletely specified in previous versions of the draft, and very
little benefit is foreseen for including that information, since
reverse path forwarding is used for the RREP.

o Additional acknowledgements were included, and contributors names
were alphabetized.





Perkins, et al. Expires April 12, 2016 [Page 104]

Internet-Draft AODVv2 October 2015


o Definitions in the Terminology section capitalize the term to be
defined.

o Uncited bibliographic entries deleted.

o Ancient "Changes" sections were deleted.

Authors' Addresses

Charles E. Perkins
Futurewei Inc.
2330 Central Expressway
Santa Clara, CA 95050
USA

Phone: +1-408-330-4586
Email: charliep@xxxxxxxxxxxx


Stan Ratliff
Idirect
13861 Sunrise Valley Drive, Suite 300
Herndon, VA 20171
USA

Email: ratliffstan@xxxxxxxxx


John Dowdell
Airbus Defence and Space
Celtic Springs
Newport, Wales NP10 8FZ
United Kingdom

Email: john.dowdell@xxxxxxxxxx


Lotte Steenbrink
HAW Hamburg, Dept. Informatik
Berliner Tor 7
D-20099 Hamburg
Germany

Email: lotte.steenbrink@xxxxxxxxxxxxxx







Perkins, et al. Expires April 12, 2016 [Page 105]

Internet-Draft AODVv2 October 2015


Victoria Mercieca
Airbus Defence and Space
Celtic Springs
Newport, Wales NP10 8FZ
United Kingdom

Email: victoria.mercieca@xxxxxxxxxx












































Perkins, et al. Expires April 12, 2016 [Page 106]

Other related posts: