[TechAssist] Re: bad again!,Sanyo DS25330 unusual symptom/fix for dead set,R409 ID?
- From: "Intrepid Video Support" <support@xxxxxxxxxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Mon, 8 Nov 2004 18:21:56 -0500
Phil,
I suppose this could be it:
Sanyo\AVM2505\Dead. Except Relay Clicks\\\\Q402 (2sd1879)*R409
(3.9-2w)*C428(1/160)\Hot*Solder Driver
Trans.\\\\\\\
Jeff
--
Intrepid Video TV/VCR Repair
263 S Front St, Steelton PA 17113
717-939-7708; (F) 717-564-4952
www.intrepid-video.com www.tech-repair.net
----- Original Message -----
From: "Phil Bader" <tjanphyl@xxxxxxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Monday, November 08, 2004 11:10 AM
Subject: [TechAssist] bad again!,Sanyo DS25330 unusual symptom/fix for dead
set,R409 ID?
Thought I fixed this problem with the STR30130 IC.(see original thread
below)
Ran all day. Turned it off, then tried to turn it on. No go. Same issue
as before. Dead. I am replacing C007 (4.7@160V) and R005 (220K) both ib
the PS near the str30130. Maybe they go bad under load, or warm.
I also have a 2 watter R409 I pulled and need to check:. Reads about 7K
but I need it's value.
Thanks.
Phil Bader
Phil Bader wrote:
>Originally set was said to be dead after storm. Tho it powered up OK on
>the bench, there were many,many bad solder connections and overheated
>areas of the board. Thoroughly resoldered, tested, and sent home.
>Customer said it never did run at home after repair. Customer returned
>it. Plugge it in. Ran good immediately. Powered on with my remote
>(customer has none) and with the front power button OK.
>I plugged it into the power strip on the test area and dead. Plugged it
>into my Sencore PoweriteII PR570 isolation transformer , and also dead.
>Even tried increasing/decreasing the line voltage.No help.
>Plugged it back in on the bench, works!
>Here's the thing:
>My bench uses a single outlet 1:1 isolation transformer that I always
>plug in the TV under test. The set WORKS with that isolated outlet.
>Plugging in direct into the UN-isolated power strip next to it DOES NOT
>let it power up. My Sencore PR570 DOES NOT let it power up.It's
>isolated! Only my small 1:1 isolation transformer at the bench lets it work.
>I replaced the STR30130 regulator, and problem cleared. Fixed! Note: The
>old str30130 outputted exactly +130 volts DC with perfect picture.
>Now I would understand it working with the isolation and not the direct
>wall outlet,(leakage) but wouldn't even power on with my Sencore
>isolation unit. Strange.
>Phil Bader
>
>
>
--
Philip Bader
Jan Phyl TV Inc. (estab. 1976)
3420 Recker Hwy. Winter Haven, Fl. 33880
Fax (863) 299-8821
email: tjanphyl@xxxxxxxxxxxxxxx
-----------------------------------------------------------------------------
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
-----------------------------------------------------------------------------
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
Other related posts:
