After replacing the kit from Tritronics Inc. supplied by Kevin Harris: (9- (1978-KIT $38.98 repair kit for 9-1978 module) Includes: FX3403 | C3460 | C3406 | C3478 | QX3201 | QX3200 | QX3402 | FLYBACK | CRX3412 | CR3215,CR3217 The set turned on but picture would go bright and dark and the convergence looked like it was unplugged from the 9-1690 board. I found CR3204, CR3206, RX3206, R3252 and the final culprit RX3210 the 1 ohm of pin 10 of the flyback that supplies the 16 volt source for the 9-1690. Thanks to all that helped on this dog. Shaun Advanced Electronics 224 West Riverview Ave. Fort Morgan, CO 80701 ----- Original Message ----- From: "Shaun" <satguy@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Friday, October 22, 2004 11:42 AM Subject: [TechAssist] Re: Zenith A60M91W1 Distorted picture still (update) > I found RX3210 on the 16 volt line open that fixed the picture problem but > now it is quit a bit to the purple color and I measured the focus block wire > and it is around 53K also I have not checked the resistors on the crt's so I > will do that. > > Shaun > > Advanced Electronics > 224 West Riverview Ave. > Fort Morgan, CO 80701 > ----- Original Message ----- > From: "drvcr" <drvcr@xxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Friday, October 22, 2004 11:30 AM > Subject: [TechAssist] Re: Zenith A60M91W1 Distorted picture still > > > > Shawn, change R3243 110K on 9-1978. Also check all 3 at 120K on all CRT > > boards, sorry can't remember locations. > > Don B. > > Dr.VCR > > 20 Hanson Ave > > Kitchener, On, Canada > > drvcr@xxxxxxxxxx > > ----- Original Message ----- > > From: "Shaun" <satguy@xxxxxxxxxxxxx> > > To: "tech" <techassist@xxxxxxxxxxxxx> > > Sent: Friday, October 22, 2004 12:42 PM > > Subject: [TechAssist] Zenith A60M91W1 Distorted picture still > > > > > > This set was dead when it came in I replaced TX3204 (flyback), Q3200 (horz > > out), QX3201, CRX3412, CR3204, CR3206, RX3206 and R3252 some of these > parts > > came in a kit from Tritronics. Now the set comes on but the picture is > > erratic and the convergence looks like it is not working at all. I > replaced > > the convergence module (9-1690) and it looks the same. I am missing > > something on the 9-1978-1 board somewhere, but I have been looking for > days > > now and can't find the problem anyone have any advice? > > > > Shaun > > > > Advanced Electronics > > 224 West Riverview Ave. > > Fort Morgan, CO 80701 > > > > > > -------------------------------------------------------------------------- > -- > > - > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > > > > -------------------------------------------------------------------------- > --- > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > -------------------------------------------------------------------------- --- > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/