John you are right about the fuse size. On the board it shows 2 amp. Checking the old fuse showed your numbers. The power supply seems to be running OK must have been using wrong ground originally, I am not sure about the horiz drive. Checking the horiz section with my Sencore TVA92 shows a problem.(HOT drawing to much current). If I disconnect the yoke and re-check, it is good. I replaced yoke with a used stock unit with the same results, (horiz section loaded down). still could be flyback problem, . The set will not start even with yoke disconnected so could be quick shutdown or no drive pulse to H.O.T. thanks Bruce. ----- Original Message ----- From: "John Mielke" <maintv2002@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Monday, October 07, 2002 5:10 PM Subject: [TechAssist] Re: Subject: Zenith SL2784 (1994) No Start, blown H.O.T. > > Hello. That module is in Sams 3482 although the model number is not > listed. That set uses 2 power supplies, QX3401 runs always and QX3402 > runs when the set comes on. Both are contolled by IC3401. RX3434 > (56K-1w) supplies start up v. I do not see a 2 amp fuse in this set, > FX3401 (AC fuse) should be 4A, FX3403 (to the horiz. output) should be > 3A and FX3402 should be 4 amp soldered-in. ICX3405 (optocoupler) sends > to on/off signal to IC3401. > This chassis is a prettty good set and they have a differt picture tube > than the ones that normally short and cause problems in the power supply > Hope this helps, John. > > Bruce Tiedeman wrote: > > Help needed, > > > > > >>Zenith SL2784BT (9-1268) Print ? Part information?.Needed. Audio working, > >>no H.V. > > > > > >>Does any one have a print to loan on this 9-1268 module. Flyback rings > > > > good? > > > >>I have 157 B+ .The Regulator circuit does not seem to be working properly. > >>This set had both 2 amp fuses blown. and H.O.T blown. Replaced blown parts > > > > , > > > >>audio only working, will not start. > >>Soldered poor connections on sweep board. The picture tube probably caused > >>the output to go and damaged the regulator circuit. The regulator does not > >>seem to be turned on , very distorted waveform. Multiple problems may not > > > > be > > > >>worth repairing, or buying print. Picture tube still questionable. > >>thanks for any information, > >>Bruce. > >> > >>B&T Electronics > >>139 Margaret St > >>Sarnia Ontario > >>Canada > >>N7T 2Y3 > >>(519) 344-1850 > >>btied@xxxxxxxxxxxx > > > > > > > > ------------------------------------------ > > To REMOVE your email address, click here: > > http://www.tech-assist.org/unsubb.html > > To CHANGE your email address, click here: > > http://www.techassist.net/forms/change.html > > ------------------------------------------ > > ***NEW*** Tips Added Instantly!!!*** > > Submit Repair Tips here: > > http://www.tech-assist.org/secure/tip/ > > > > > > > -- > John Mielke > Main TV > Longmont,Co > 303 776 6955 > maintv2002@xxxxxxxxxxxxx > > > ------------------------------------------ > To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html > To CHANGE your email address, click here: > http://www.techassist.net/forms/change.html > ------------------------------------------ > ***NEW*** Tips Added Instantly!!!*** > Submit Repair Tips here: > http://www.tech-assist.org/secure/tip/ > ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html To CHANGE your email address, click here: http://www.techassist.net/forms/change.html ------------------------------------------ ***NEW*** Tips Added Instantly!!!*** Submit Repair Tips here: http://www.tech-assist.org/secure/tip/