Thanks Jim for all the good tips.I will be doing this tomorrow and will take whatever I have here to do the job. Mando AZ Jim Myers wrote: > That is a PTK195 and you'll probably need to repair the separate > convergence power supply board. > > --------------------------------------------------------------- > Text pasted from WinSTIPS 2.0 > http://www.ServiceSoftware.com > --------------------------------------------------------------- > > PROSCAN PTK195CP > > Convergence Distorts Bad, And Pix Bows In From - Top & Bot. Usually > After On A While. > > Robinson Electronics > > Replace (Burnt Open) Resistor R19233 On Convergence Board. 15k Ohms 3w. > Mfr# 182374. > > --------------------------------------------------------------- > > RCA PTK195 > > Convergence Bad. Bowed In Top And Bottom. No Voltages J19701 > > E-C Short On Q19707 (Smd) Amp On Conv Power 1 Bd > > --------------------------------------------------------------- > > RCA PTK195 > > Convergence Bad. Pincushion Bowed In From Top And Bottom. > > Robinson Electronics Chassis = PTK195DC > > Replaced Bad Conv. Pwr. Board. Rca# 250686 (Was #242675). > > --------------------------------------------------------------- > > RCA PTK195 > > Convergence Menu (Customer Menu) Is Missing > > Heatsinks On Digicon Board Were Cold. Told By Rca Techline To > Replace/Check Cr19709/10, Q19504 And Eprom On Digicon Board U19201 (8) > For 5 Volts, All Of Those Devices Were Good. > > Started Checking Voltages And Found R19703 Was Open On Convergence Power > Board, 750k 1/2watt. > > --------------------------------------------------------------- > > RCA PTK195 > > Convergence Not Working And No Convergence Osd On Menu. > > Garris Radio & Tv - New Bern, Nc. > > Replace R19703 (750k-1/4w 193334) Even If It Checks Good. (Sometimes It > Does Check Good And The Reg Ic Will Be Bad) And Change U19700 > (Stk730-130 215530). This Will Restore Convergence And The Convergence > Osd Menu! > > --------------------------------------------------------------- > > The Old Master Technician > ******************************** > Since 1972 * > Jim Myers * > Telrad Electronics * > Fort Wayne Indiana * > ******************************** > > armando guerra wrote: > > I have to do a service call on this model and according to the > > customer,the convergence is real bad.The pix is curved at the top and > > bottom also.Don't have the manual so I thought I would ask some of you > > techs what # for the stk's or is it a complete convergence bd that has > > to be replaced.Would like to know so that I can take what I have here as > > far as parts is concerned.Thanks for your tips and help. > > Mando > > AZ > > > > ----------------------------------------------------------------------------- > > This Email List is accessible to the general public through search engines. > > Remove: http://www.tech-assist.org/remove.htm > > Set Vacation > > mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation > > Lost Password: http://www.tech-assist.org and select "Login Problems?". > > Email Archives: //www.freelists.org/archives/techassist/ > > > ----------------------------------------------------------------------------- > This Email List is accessible to the general public through search engines. > Remove: http://www.tech-assist.org/remove.htm > Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation > Lost Password: http://www.tech-assist.org and select "Login Problems?". > Email Archives: //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- This Email List is accessible to the general public through search engines. Remove: http://www.tech-assist.org/remove.htm Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/