With 98K to ground you have no shorts. C1622 and C7411 should be ok (I've never seen an NPO cap fail). If you used an 8 pin DIP socket to install the IC check it is seated properly. Is there any data/clock pulses present on pins 5 & 6? Jerry's TV Service (Since 1978) 840 So. Kansas Ave Liberal, KS 67901 620-624-4302 jhoeme@xxxxxxxxxxxxx ----- Original Message ----- From: "Larry E" <videotech@xxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Thursday, September 30, 2004 3:54 PM Subject: [TechAssist] Re: RCA G35772AT CTC187CL DEAD/More info Jerry, resistance is 98K pin 6 to ground or across R3204, I can`t find C1622 or C7411 can you advise where they are located? Larry E Larry Eastman American TV& Electronics Crystal River, Fl. 34428 jhoeme@xxxxxxxxxxxxx wrote: > What is the resistance from pin 6 of U3201 to ground? If you recently did > a > resolder in the tuner wrap check for solder bridges. Also check R3204 > (100K), C7411 (10pf NPO), C1622 (22pf NPO) > > Jerry's TV Service (Since 1978) > 840 So. Kansas Ave > Liberal, KS 67901 > 620-624-4302 > jhoeme@xxxxxxxxxxxxx > > ----- Original Message ----- > From: "Larry E" <videotech@xxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Thursday, September 30, 2004 12:21 PM > Subject: [TechAssist] Re: RCA G35772AT CTC187CL DEAD/More info > > Hi Guys, replaced the eprom and still have the same problem, zero volts on > pin 6, > > 4.32 on pin 8&5. Unsoldered pin 54 of U1001 thinking it might have been > pulling > it down, no change, Q4105 is supposed to be the 5v standby source? (no > schematic) > > I have ( measured to cold ground) E= 4.77 B= 5.1 C= 11.7 volts. Could > the > 4.32 > > be too low on pins 8 & 5 ? I was told pins 5&6 get the 5 volts from pin 8 > of > U3201 > so I`m still confused how pin 5 can have 4.32 but pin 6 would be zero if > the > source > is internally from pin 8 even with a new eprom installed, HELP!!! Larry > E > > Larry Eastman > American TV & Electronics > Crystal River, Fl. 34428 > > Larry E wrote: > > > Hi Guys, this 187CL is stone dead, no click from relay, HOT is good, > > have 160 v on collector > > in standby, resoldered H- driver transformer and the coil, C4107 is > > good, found a bad > > C4105 10uf @ 200 replaced it with no change, I need to know if the > > voltages are correct > > on U4101 as I don`t have the schematic, they are > > Pin 1= -40 > > 2= -33 > > 4= 0 > > 5= .9 > > 6= .9 > > 7= .4 > > 8&9 = 0 > > 11&12 = 165 thanks in advance, Larry E > > Larry Eastman > > American TV & Electronics > > Crystal River, Fl. 34428 > > > > ----------------------------------------------------------------------------- > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > ----------------------------------------------------------------------------- > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ > > ----------------------------------------------------------------------------- > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/