Hello Ralph. That is what I did yesterday. It turn out to be the splitter is bad.I just cut the lead and put it to a glass vase and and close with a plastic cap. Thanks for that ,Ralph. Dang TVCR ----- Original Message ----- From: "Ralph Dorsey" <Merlin-Wizard@xxxxxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Wednesday, January 30, 2002 1:23 AM Subject: [TechAssist] Re: Proscan CTC 169bg5 shut down > take the lead going from flyback and remove it from the high voltage > splitter. then place it an an emprty dry soda bottle and try and see > if the set turns on then. If so bad high voltage splitter. the set > actually "cycles" when you plug it in, and if the splitter is bad, it > won't even turn on > > Tomlee wrote: > > >Hello Phil. > >Yes I do have 15v at cr4418. I will check C4402. > > c4401 and c4402 connect together from HOT (collector) to ground. > >Thanks > >----- Original Message ----- > >From: "Phillip R. Hull" <phil245@xxxxxxxxxxxxx> > >To: <techassist@xxxxxxxxxxxxx> > >Sent: Monday, January 28, 2002 11:31 AM > >Subject: [TechAssist] Re: Proscan CTC 169bg5 shut down > > > > > >>Did you change CR4118 yet?(Do you have 15v) If so change C4402, if > >> > >this > > > >>cap goes just a little low in value I have seen the set shut down > >>Phillip R Hull > >>phil245@xxxxxxxxxxxxx > >>----- Original Message ----- > >>From: "Tomlee" <t8872695@xxxxxxxxxxxxx> > >>To: <techassist@xxxxxxxxxxxxx> > >>Sent: Monday, January 28, 2002 1:31 PM > >>Subject: [TechAssist] Proscan CTC 169bg5 shut down > >> > >> > >>>Hello fellow tech. > >>>I am working with ctc 169bg5. with the help with other techs Perry, > >>> > >JBC.I > > > >>>force to turn on the tv by apply 5v at base of > >>>Q4306. But the tv show a sign of on and off cycle. I do not hear the > >>> > >>sound > >> > >>>of high voltage . I use the sencore to ring the > >>>flyback by one end of probe to the B+ and the other end to colector of > >>> > >HOT > > > >>>as sencore manual direction. But Get zero > >>>ring .If I remove cr402 and L803 I will get maximum 30 rings.(The HOT > >>>colector connect to ground by 2 diode CR 401 and cr402 ). I means If > >>> > >The > > > >>>HOT collector connect to ground or connect to pincustion circuit(through > >>>L803) It will make zero ring on flyback test.Does this means somthing > >>> > >>wrong > >> > >>>at pincushion ckt or B+ to ground ckt . I measure no short to B+. . > >>>May be it is only short to horizontal frequency?.Any Ideas from > >>> > >experince > > > >>>tech is appriciated.I spend too much time for this . > >>>Dang TVCR > >>> > >>>------------------------------------------ > >>>Make your TechAssist database better! > >>>Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > >>>------------------------------------------ > >>>To UNSUBSCRIBE your email address, click here: > >>>mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >>>Or send a BLANK email with unsubscribe in the > >>>SUBJECT field to the address above. > >>> > >>> > >>------------------------------------------ > >>Make your TechAssist database better! > >>Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > >>------------------------------------------ > >>To UNSUBSCRIBE your email address, click here: > >>mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >>Or send a BLANK email with unsubscribe in the > >>SUBJECT field to the address above. > >> > > > >------------------------------------------ > >Make your TechAssist database better! > >Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > >------------------------------------------ > >To UNSUBSCRIBE your email address, click here: > >mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >Or send a BLANK email with unsubscribe in the > >SUBJECT field to the address above. > > > > > > > > ------------------------------------------ > Make your TechAssist database better! > Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > ------------------------------------------ > To UNSUBSCRIBE your email address, click here: > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > Or send a BLANK email with unsubscribe in the > SUBJECT field to the address above. > ------------------------------------------ Make your TechAssist database better! Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ ------------------------------------------ To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe Or send a BLANK email with unsubscribe in the SUBJECT field to the address above.