Avery, CTV and Projo Service Mode, Chassis AMEDP, APEDP, AREDP 1.. With set on, select setup. Switch to cable,(if it's already in cable, switch to ant, then back to cable.) 2.. Press action and go to timer, select greater than 30 minutes, action out, enter 124. 3.. Press volume down on TV to zero volume, a red check should appear, you may select an active station or video input at this time. If you think the adjustments will take longer than the time set on the sleep timer, go into the menu and turn it off. Failure to do so may result in the set powering down. 4.. To toggle between Serviceman and Aging Modes press ACTION and VOL UP at the same time on the control panel. 5.. The set is now in the Serviceman mode. 6.. Press power button on the remote to select one of the five Serviceman Adjustment Modes. B = VCJ Sub Adjustments C = VCJ Cut-off Adjustments S = Options, (PIP and clock adjustments) M = MTS Adjustments CHK = Normal operation of Channel and Volume controls 7.. Channel Up/Down will change the register and Volume Up/Down will change the value. 8.. Write down the initial settings before you adj anything in case you want to put them back. 9.. When you are finished you must exit the service mode by doing a soft reset. Press action and power on the TV for about 5 seconds. The screen will blank and then OSD will show all that has been checked by the micro. The set is like out of the box, and all customer settings are gone. CTV METHOD 2, some other models 1.. Short test point FA1 to cold ground FA2 (A-board: TP pin 8 to pin 3) 2.. Receiver is in Aging Mode with yellow 'CHK' in the upper-left corner 3.. Press ACTION and VOL+ simultaneously on the control panel and 'CHK' should be in red 4.. The set is now in Serviceman Mode, press POWER on remote to select one of the five Serviceman Adjustment Modes: B = VCJ Sub Adjustments C = CRT Adjustments D = Pincushion Adjustments S = Options Adjustments (PIP and clock) 5.. Press CHAN UP / DOWN on remote to select an item 6.. Press VOL LEFT / RIGHT to adjust 7.. To exit service mode hold Action and Power buttons on the TV for 5 seconds CTV METHOD 3 TX-W28R3 (and similar models) 1.. Set BASS to maximum position, set TREBLE to minimum position 2.. Press REVEAL on the remote control and at the same time press VOLUME on the TV. This will place the TV into the Service mode 3.. Press the RED / GREEN buttons to select an item 4.. Press the YELLOW / BLUE buttons to adjust 5.. Press STORE on the preset panel after each adjustment has been made to store the required values 6.. To exit the Service Mode, press NORMALIZATION CTV, Some Models, (CT27S18C) Using original remote, press action and volume up buttons at the same time. Press power button to select modes. William Rayburn, CET Premium Technologies PO Box 442 Long Beach, WA. 98631 360-642-4993 ----- Original Message ----- From: "Avery Boyd" <adBoyd@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Wednesday, September 28, 2005 10:07 AM Subject: [TechAssist] Panasonic modelpt51hx40b how do you get into the converg menue? How do you get into the converge menue, on this model pt51hx40b Panasonic? Avery Boyd 4666B S. Mingo Tulsa OK 74146 Phone 918-665-2400 ----------------------------------------------------------------------------- This Email List is accessible to the general public through search engines. Remove: http://www.tech-assist.org/remove.htm Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- This Email List is accessible to the general public through search engines. Remove: http://www.tech-assist.org/remove.htm Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/