.01 uf cap ....disc type....ones Radio Shack work fine if you have none. I'll do the mod on the chassis itself on these sets.....on the projections I'll cut the VP plug from the PIP so we don't have to pull the chassis. Jeff Stielau Shoreline Electronics Repair 125 Beechtree Lane Westbrook,CT 06498 860-399-1861 Voice 860-664-3535 Fax jstielau@xxxxxxxx ----- Original Message ----- From: "Mike Barnett" <passthecash@xxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Saturday, October 13, 2001 7:32 AM Subject: [TechAssist] Re: Mitsubishi Model cs-26301 PIP module > > Jeff, thanks ALOT! This is great info. could you elaborate a bit more, pin 7 > to pin 9 you say install .01 is this a resistor? if so at what wattage(1/8 > 1/4 1/2??) or doesn't it matter? should i modify the main board and leav the > pip out or do the mod on the pip mod and re-install? > Thanks again > Mike > > > > > > On Fri, 12 Oct 2001 19:34:51 -0400, techassist@xxxxxxxxxxxxx wrote: > > > > > Mike, > > > > If the customer never uses the PIP it's best to bypass the board....it > may > > cause more problem years from now. > > > > Here's the bypass procedure : > > > > Remove "Vp" Plug From Pip Mod.Install .01 From Pin 7 To Pin 9 Install > > 4.7/35-50v;Pos.To Pin 5,Neg. To Pin 11 > > > > If it's a set we have on the bench , I'll solder the 2 parts on the > bottom > > of the chassis instead of having to remove the plug from the PIP. > > > > We do keep a VP plug all ready to go in our service kit for a quick > bypass > > check in the field or on the bench. > > > > Jeff Stielau > > Shoreline Electronics Repair > > 125 Beechtree Lane > > Westbrook,CT 06498 > > 860-399-1861 Voice > > 860-664-3535 Fax > > jstielau@xxxxxxxx > > > > ----- Original Message ----- > > From: "Mike Barnett" <passthecash@xxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Friday, October 12, 2001 2:42 PM > > Subject: [TechAssist] Mitsubishi Model cs-26301 PIP module > > > > > > > > > > Anyone know a good source for the pip module in model# cs-26301. > > > PIP module # P12187258. this unit has loss of vertical hold after on > about > > 5 > > > min. Pulled pip mod and has leaky smd caps all over it with > contaminated > > > traces. Dont want to even try to rebuild. any help would be great. > > > > > > Thanks, > > > Mike > > > > > > > > > Get It Fixed At > > > Rochester Electronics > > > 630 West Ridge Rd. > > > Rochester, NY 14615 > > > 716.663.6870 > > > www.RochesterElectronicsRepair.com > > > > > > > > > > > > > > > > > > _______________________________________________________ > > > Send a cool gift with your E-Card > > > http://www.bluemountain.com/giftcenter/ > > > > > > > > > Help make your TechAssist online repair tips > > > database better! Submit your fixes here: > > > http://www.circuitwork.com/techassist/tip/#tips > > > To unsubscribe write to: > > > techassist-request@xxxxxxxxxxxxx > > > with unsubscribe in the subject line. > > > > > > > Help make your TechAssist online repair tips > > database better! Submit your fixes here: > > http://www.circuitwork.com/techassist/tip/#tips > > To unsubscribe write to: > > techassist-request@xxxxxxxxxxxxx > > with unsubscribe in the subject line. > > > Get It Fixed At > Rochester Electronics > 630 West Ridge Rd. > Rochester, NY 14615 > 716.663.6870 > www.RochesterElectronicsRepair.com > > > > > > _______________________________________________________ > Send a cool gift with your E-Card > http://www.bluemountain.com/giftcenter/ > > > Help make your TechAssist online repair tips > database better! Submit your fixes here: > http://www.circuitwork.com/techassist/tip/#tips > To unsubscribe write to: > techassist-request@xxxxxxxxxxxxx > with unsubscribe in the subject line. > Help make your TechAssist online repair tips database better! Submit your fixes here: http://www.circuitwork.com/techassist/tip/#tips To unsubscribe write to: techassist-request@xxxxxxxxxxxxx with unsubscribe in the subject line.