[sib-access] Re: sibelius can not count bars after second endings
- From: "Dale Lieser" <dale.lieser@xxxxxxxxx>
- To: <sib-access@xxxxxxxxxxxxx>
- Date: Sun, 3 Jun 2012 22:08:10 -0400
Just wait, Annabelle. Any explanations Dan would have to give now would
likely take him away from his work on the scripts and documentation.
-----Original Message-----
From: sib-access-bounce@xxxxxxxxxxxxx
[mailto:sib-access-bounce@xxxxxxxxxxxxx] On Behalf Of Farfar, Chairman of
the Lodge
Sent: Sunday, June 03, 2012 9:48 PM
To: sib-access@xxxxxxxxxxxxx
Subject: [sib-access] Re: sibelius can not count bars after second endings
Annabelle,
Only Dan knows, but we may all just be prepared to accept that it will allow
us to use Sibelius 6 to the same extent to which we can now use Sibelius 5.
That alone is a big plus.
Dave Carlson
Reasonable care was taken by the author, to generate consistent and
grammatically correct sentence structure, using a Dell Latitude E6520, JAWS
13.0.718, and Windows 7 Professional 32-bit
----- Original Message -----
From: "Annabelle Susan Morison" <foristnights@xxxxxxxxxxx>
To: <sib-access@xxxxxxxxxxxxx>
Sent: Sunday, June 03, 2012 07:28
Subject: [sib-access] Re: sibelius can not count bars after second endings
I was wondering, what will be included in this upcoming release of Sibelius
Access 6?
-----Original Message-----
From: sib-access-bounce@xxxxxxxxxxxxx
[mailto:sib-access-bounce@xxxxxxxxxxxxx] On Behalf Of Dan Rugman
Sent: Thursday, May 31, 2012 2:32 PM
To: sib-access@xxxxxxxxxxxxx
Subject: [sib-access] Re: sibelius can not count bars after second endings
Ramy,
You are not hearing bar numbers because the repeats are not properly
matched. Every end repeat barline must have a start repeat barline unless
the repeat is back to the beginning of the score. More importantly, you
cannot have repeats inside other repeats. Sibelius doesn't like that at all.
EG: start repeat - start repeat - end repeat - end repeat will throw the bar
numbering and cause problems with playback.
Dan
-----Original Message-----
From: sib-access-bounce@xxxxxxxxxxxxx
[mailto:sib-access-bounce@xxxxxxxxxxxxx] On Behalf Of Ramy Moustafa
Sent: 31 May 2012 20:07
To: sib-access@xxxxxxxxxxxxx
Subject: [sib-access] sibelius can not count bars after second endings
HI all:
Don't know why, but I have a score here has some 1st and second endings,
sibelius can count the bar numbers ok, before them, but after them, sibelius
left some mesures without numbering, then continue to count,
I tried the ingraving rools, to count repeat bar lines, but without success.
I tried, the bar nubmer change, and I went to the bar that I need to start
counting from it, but no luck also, any idea on how to achieve this?
Thanks in advance
Cheers:
Ramy Moustafa
Owner and producer of Harmony recording studios
skype:
roma30
Facebook:
moustafa.ramy@xxxxxxxxx
Twitter:
Ramymoustafa
youtube chanael:
www.youtube.com/ramymoustafasaber
If you wish to unsubscribe, send a blank message with the single word,
unsubscribe - in the Subject line to:
sib-access-request@xxxxxxxxxxxxx
If you wish to unsubscribe, send a blank message
with the single word, unsubscribe - in the Subject line to:
sib-access-request@xxxxxxxxxxxxx
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2012.0.2178 / Virus Database: 2425/5036 - Release Date: 05/31/12
If you wish to unsubscribe, send a blank message
with the single word, unsubscribe - in the Subject line to:
sib-access-request@xxxxxxxxxxxxx
If you wish to unsubscribe, send a blank message
with the single word, unsubscribe - in the Subject line to:
sib-access-request@xxxxxxxxxxxxx
If you wish to unsubscribe, send a blank message
with the single word, unsubscribe - in the Subject line to:
sib-access-request@xxxxxxxxxxxxx
Other related posts:
