Just been in shack for a while either side of 15:00 local and the tx frequency looks OK now. I was only talking about the last 10 Hz or less for the Fldigi sound card TX off set. I guess the idea was to fill in the last bit below the smallest VFO step which could be done with XIT etc. Again it's is fine for testing as it is. If long term you are changing things including radio leave the radio side as is and enjoy. Re Beacons I did see some almost clashes and you seem to have 2 beacons in each minute. There has been clashes with Client beacons when a few have been on so maybe the client needs a second 5 minute block for 30 minute beacons.
73 Roger On 06/03/2011 14:53, Pär Crusefalk wrote:
Hi,Be careful if you move using fldigi as that 500 Hz filter could cut the high or the low end of the audio. I'd move using the VFO for now.Regarding the TX'ing you have a point that too many beacons will at some point hurt us. During the last conference we all agreed that a server should not beacon more than once per hour and frequency so I suggest you keep it simple and only beacon once (until you start covering more frequencies that is).More servers are always needed! There are of course many servers on 10147 now and perhaps we can use your server to cover more areas? If I can wish out loud then it would be great if you could cover 40 meters. For instance we have Torsten, SA2ATJ, up in Luleå that will sail soon and our coverage up there is not perfect now. 40 Meters would help him and others up there. 40 from your QTH should be good in middle europe during mornings and evenings too.A proper installation is very good, that way you can set it up with cron jobs that fetch files for the users, web server access etc. Lots to learn still ;-)73 de Per SM0RWO 2011-03-06 15:23, Gunnar Bulukin skrev:OK Roger got that and will check settings again. From what I understand itseems to connect ok now. One thing that I have to talk to Rain/Pär/? about is if I make my serverpermanent if 1101 on the hr, 20 and 40 is ok to TX on without to interfere with the other servers. Also if it is needed to have an server at my QTH? Noidea to fill the world with servers!!! If ok I have to get a new rig for this because the IC-706MKIIG I will install in my sailing boat and the 2 IC-707, from what I understand, are difficult to get to work with this apl. (a bit to old!)I also need to make a new installation of Ubuntu on my fanless computer tomake things more permanent, CD and stick is ok but not optimal.Going from 0 to 30% learning has taken some time going from 31 to 100% will take quite some time more and there are more things around the house thathas to be taken care of;-) 73 de Gunnar -----Ursprungligt meddelande-----Från: pskmail-bounce@xxxxxxxxxxxxx [mailto:pskmail-bounce@xxxxxxxxxxxxx] FörG6CKR Skickat: den 6 mars 2011 14:55 Till: pskmail@xxxxxxxxxxxxx Ämne: [pskmail] Re: SV: Re: SV: Re: SV: Re: SV: Re: Ping You don't need Cat control for the sound card tweak it just moves the actual audio tone tx frequency up or down by the set adjustment. Your TX frequency is made up of the dial frequency plus the waterfall setting say 1KHz.If your actual TX frequency turns out to be say 10 Hz too high, setting -10 in Fldigi sound card TX offset will make the tone centre 990 Hz and correctthe difference.It is there for situations where the RX frequency is fine but the TX needsminor adjustment. 73 Roger G6CKR On 06/03/2011 13:43, Gunnar Bulukin wrote:I am not using CATcontrol so I am changing on the rig. I will go back to .01 from .00 1315Z 73 Gunnar -----Ursprungligt meddelande----- Från: pskmail-bounce@xxxxxxxxxxxxx [mailto:pskmail-bounce@xxxxxxxxxxxxx] För G6CKR Skickat: den 6 mars 2011 12:29 Till: pskmail@xxxxxxxxxxxxx Ämne: [pskmail] Re: SV: Re: SV: Re: SV: Re: Ping go 10146.1 first a .2 jump will be too far. the .1 might be as well You can make small changes in fldigi under sound card TX off set 1Hz at a time add - for lower just the number for higher. But you are close enough to wait for a few more opinions before you do anything. 73 Roger On 06/03/2011 11:19, Gunnar Bulukin wrote:Ok Roger, I will change down to 10146,0 from 10146,02 please inform me if there is an improvement. If you have the time can you send me a mail via my mail gate. 73 de Gunnar -----Ursprungligt meddelande----- Från: pskmail-bounce@xxxxxxxxxxxxx [mailto:pskmail-bounce@xxxxxxxxxxxxx] För Roger G6CKR Skickat: den 6 mars 2011 11:29 Till: pskmail@xxxxxxxxxxxxx Ämne: [pskmail] Re: SV: Re: SV: Re: Ping Done and it works. First connect failed. Second was OK. Server update seemed to go through but I did not get a message back the first time. After the "don't know how " message the second update was acknowledged OK and a mail check worked. As there was not mail (as expected) I downloaded the Fleet codes. There were some repeats but not enough to cause a mode change. Final observation, you TX may be a few Hz HF still, compared to SM0RWO but it is not far. 73 Roger G6CKR On Sun, 2011-03-06 at 08:43 +0100, Gunnar Bulukin wrote:Hi Roger,As you are running a client could you test if you can use my mailgate?73 de Gunnar -----Ursprungligt meddelande----- Från: pskmail-bounce@xxxxxxxxxxxxx [mailto:pskmail-bounce@xxxxxxxxxxxxx] För G6CKR Skickat: den 5 mars 2011 18:14 Till: pskmail@xxxxxxxxxxxxx Ämne: [pskmail] Re: SV: Re: Ping So if we change the tx setting from 10146.1 to 10146.0 that should get you to within 20 Hz I think. if I'm right you will actually be 20 Hz low which you can add to the Fldigi sound card TX off set. But do it a step at a time. look forward to gating you....... Just checked and I have gated you at 17:02 73 Roger. On 05/03/2011 17:01, Rein Couperus wrote:Hej Gunnar, your server is working, but the TX is 80 Hz too high in frequency... I got a connect, but 80 Hz difference is really too much.... Pse check with a second receiver, and take IS0GRB-3 as a referencefrequency...Tnx, Rein EA/PA0R/MHi Rein, With some excellent help from Pär I thing that it is working now.We changed the BFO from 600> 900 and TX from 10146,2> 10146,1USB.Now I am getting beacon from G6CKR with no problems. Maybee now someone can ping me and test if it is working. Pär told me that there is a program to test the mailfunktion but it was not on the server cd. Can you tell me how to get it? 73 de gunnar -----Ursprungligt meddelande----- Från: pskmail-bounce@xxxxxxxxxxxxx [mailto:pskmail-bounce@xxxxxxxxxxxxx] För Rein Couperus Skickat: den 5 mars 2011 11:51 Till: pskmail@xxxxxxxxxxxxx Ämne: [pskmail] Re: Ping Hi Gunnar, I have not been able to hear the server yet, but condx are not good at the moment between us... this what is in my list thismorning:09:01 - SM0RWO>PSKAPR,TCPIP*:!5901.16NP01756.10E& 09:02 - IS0GRB-3>PSKAPR,TCPIP*:!3914.79NP00910.96E& 10:02 - IS0GRB-3>PSKAPR,TCPIP*:!3914.79NP00910.96E& 11:02 - IS0GRB-3>PSKAPR,TCPIP*:!3914.79NP00910.96E&You can see not even SM0RWO makes it into the Igate at the moment...IS0GRB-3 is booming in here... Rein EA/PA0R/M ===================================================== Hi, Has anyone been able to hear or ping SA6BQZ? TX10146,2 USB RX10147 CW-N 73 de gunnar KB Vågspel [www.vagspel.se] Gunnar Bulukin Tel +46(0)31 962130 Mob +46(0)31 7601501 SMS +46(0)705 933051 This message has been scanned by Avast for Microsoft Outlook P Please consider your environmental responsibility. Before printing this e-mail ask yourself:- "Do I need a hard copy?"