2BA wide pitched or 4 BA close pitched > O.K. Thanks, Ron. What BA size(s) would you suggest > for a model cylinder that is 1-5/8" bore x 3" stroke? > > Al Messer > > > --- Ron Head <ron.head@xxxxxxxxxxxxx> wrote: > > > Hi Al > > > > No-one else has replied, so I'll bite. > > > > As far as British locos are concerned, the only > > place I've seen slotted > > screws is in the boiler cleading - usually around > > the backhead area where > > small pieces are joined together, or where feed pipe > > covers and the like are > > attached. > > > > Regards > > Ron > > > > ----- Original Message ----- > > From: "Allen Messer" <al_messer@xxxxxxxxx> > > To: <modeleng@xxxxxxxxxxxxx> > > Sent: Monday, September 26, 2005 4:26 PM > > Subject: [modeleng] Re: No new topic ? > > > > > > > O.K. I have awakened from my Cold Medicine > > induced > > > stupor long enough to think of something to ask: > > > When, if ever, were slotted head screws used on > > full > > > sized prototype steam engines, and where would it > > be > > > appropriate to use them on a scale model? > > > > > > Al Messer > > > > > > --- lanchhale@xxxxxxxxxxxxxxxx wrote: > > > > > >> Dave > > >> > > >> I was lucky enough to be offered a drive of the > > >> Royal Scot after you left. > > >> It was beautiful but so large after the 1366, > > the > > >> dome was where her > > >> chimney is!! > > >> > > >> Just as we were about to load her up the weather > > >> broke & we got soaked, > > >> but after that drive albeit short it didnt really > > >> matter!! > > >> > > >> See you tomorrow. > > >> > > >> Cheers > > >> > > >> Adrian > > >> > > >> > Get well soon guys. I have been soooooo busy > > with > > >> my daughters birthday > > >> > party. We had a 71/4 GWR13XX, a 7 1/4 Scot, (A > > >> proper engine!!), a 7 1/4 > > >> > Britania and a 5"Martin Evans B1, that was on > > the > > >> ground level. On the > > >> > raised level we had a 5"Brit and my 5" IoM > > Beyer > > >> peacock. A great day was > > >> > had by all, the older kids enjoyed it more me > > >> thinks! > > >> > > > >> > Thats all over now so back to the workshop to > > >> fettle my stationary engines > > >> > for Tues club night. > > >> > > > >> > Dave. > > >> > ----- Original Message ----- > > >> > From: "Allen Messer" <al_messer@xxxxxxxxx> > > >> > To: <modeleng@xxxxxxxxxxxxx> > > >> > Sent: Sunday, September 25, 2005 1:47 AM > > >> > Subject: [modeleng] Re: No new topic ? > > >> > > > >> > > > >> > Well, I've felt too badly all day to even take > > off > > >> my > > >> > pajamas much less think of something, BUT, you > > >> just > > >> > wait until I'm rid of this snotty-nosed Cold!! > > >> > > > >> > Al Messer > > >> > > > >> > --- Pcx <pierre.courbouleix@xxxxxxxxxx> wrote: > > >> > > > >> >> Hi LIst, > > >> >> Still alive ? No new topic since 72 hours ! > > >> >> PIerre > > >> >> MODEL ENGINEERING DISCUSSION LIST. > > >> >> > > >> >> To UNSUBSCRIBE from this list, send a blank > > email > > >> >> to, > > >> >> modeleng-request@xxxxxxxxxxxxx with the word > > >> >> "unsubscribe" in the subject line. > > >> >> > > >> > > > >> > > > >> > > > __________________________________________________ > > >> > Do You Yahoo!? > > >> > Tired of spam? Yahoo! Mail has the best spam > > >> protection around > > >> > http://mail.yahoo.com > > >> > MODEL ENGINEERING DISCUSSION LIST. > > >> > > > >> > To UNSUBSCRIBE from this list, send a blank > > email > > >> to, > > >> > modeleng-request@xxxxxxxxxxxxx with the word > > >> "unsubscribe" in the subject > > >> > line. > > >> > > > >> > > > >> > > > >> > MODEL ENGINEERING DISCUSSION LIST. > > >> > > > >> > To UNSUBSCRIBE from this list, send a blank > > email > > >> to, > > >> > modeleng-request@xxxxxxxxxxxxx with the word > > >> "unsubscribe" in the subject > > >> > line. > > >> > > > >> > > > >> > > >> > > >> MODEL ENGINEERING DISCUSSION LIST. > > >> > > >> To UNSUBSCRIBE from this list, send a blank email > > >> to, > > >> modeleng-request@xxxxxxxxxxxxx with the word > > >> "unsubscribe" in the subject line. > > >> > > > > > > > > > __________________________________________________ > > > Do You Yahoo!? > > > Tired of spam? Yahoo! Mail has the best spam > > protection around > > > http://mail.yahoo.com > > > MODEL ENGINEERING DISCUSSION LIST. > > > > > > To UNSUBSCRIBE from this list, send a blank email > > to, > > > modeleng-request@xxxxxxxxxxxxx with the word > > "unsubscribe" in the subject > > > line. > > > > > > > > > -- > > > No virus found in this incoming message. > > > Checked by AVG Anti-Virus. > > > Version: 7.0.344 / Virus Database: 267.11.6/111 - > > Release Date: 23/09/2005 > > > > > > > > MODEL ENGINEERING DISCUSSION LIST. > > > > To UNSUBSCRIBE from this list, send a blank email > > to, > > modeleng-request@xxxxxxxxxxxxx with the word > > "unsubscribe" in the subject line. > > > > > > > __________________________________ > Yahoo! Mail - PC Magazine Editors' Choice 2005 > http://mail.yahoo.com > MODEL ENGINEERING DISCUSSION LIST. > > To UNSUBSCRIBE from this list, send a blank email to, > modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the subject line. > MODEL ENGINEERING DISCUSSION LIST. To UNSUBSCRIBE from this list, send a blank email to, modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the subject line.