[PCB_FORUM] Re: drill legend

Thanks to all, especially this one.  Nice hidden trick. 


Patrick Westfeldt, Jr.
720-406-0887

-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Douglas Stanley
Sent: Tuesday, March 07, 2006 10:24 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: drill legend

One thing you may not be aware of is you can reset where you want the table
to reside. 

When you're in the "Drill Legend" popup and click OK, the table gets
attached to your cursor. No matter where you click, it'll snap back to where
the previous chart was located. 

However, if (while the table is attached to the cursor) you right-click and
choose cancel, the system will "forget" where the original table was and
will allow you to place the new chart anywhere you want (when you re-invoke
the "Drill Legend" popup).


Douglas G. Stanley
Broadcom Corporation
(949) 926-5889
dstanley@xxxxxxxxxxxx 

 



-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx]
Sent: Tuesday, March 07, 2006 8:19 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: drill legend

Pat,

        Also, once you have placed it you can move it, as a group object, to
where you would like it to permanently reside.

Jerry


-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Peter Hughes
Sent: Tuesday, March 07, 2006 11:05 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: drill legend


When the drill legend is regenerated it is placed according to the following
criteria. If there is an existing legend then the new one goes in the same
place. If there is no legend then it will be placed at the location of the
user pick.

Rgrds
 
Peter Hughes,
PCB Designer,
Concurrent Technologies,
4 Gilberd Close,
Newcomen Way,
Colchester,
Essex,
CO4 4WN.
Tel: +44 1206 752626
Fax: +44 1206 751116

-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of westfeldt
Sent: 07 March 2006 15:54
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] drill legend

How do you position the drill legend in v 15.2 and up?  Sometimes it shows
up right in the middle of my board and I can't see how to make it come up in
any different location.

Patrick Westfeldt, Jr.
North Boulder Circuit Design
westfeldt_nbcd@xxxxxxxxx
720-406-0887
c 720-272-5822


-----------------------------------------------------------
To subscribe/unsubscribe: 
        Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
        with a subject of subscribe or unsubscribe

To view the archives of this list please login at http://www.freelists.org.
Our list name is icu-pcb-forum or go to
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
        Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx

Want to post a job listing ?  DON'T DO IT HERE!  
Better yet, join our jobs listing forum.

SUBSCRIBE:  icu-jobs-forum-subscribe@xxxxxxxxxx
POST:       icu-jobs-forum@xxxxxxxxxx
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe: 
        Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
        with a subject of subscribe or unsubscribe

To view the archives of this list please login at http://www.freelists.org.
Our list name is icu-pcb-forum or go to
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
        Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx

Want to post a job listing ?  DON'T DO IT HERE!  
Better yet, join our jobs listing forum.

SUBSCRIBE:  icu-jobs-forum-subscribe@xxxxxxxxxx
POST:       icu-jobs-forum@xxxxxxxxxx
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe: 
        Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
        with a subject of subscribe or unsubscribe

To view the archives of this list please login at http://www.freelists.org.
Our list name is icu-pcb-forum or go to
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
        Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx

Want to post a job listing ?  DON'T DO IT HERE!  
Better yet, join our jobs listing forum.

SUBSCRIBE:  icu-jobs-forum-subscribe@xxxxxxxxxx
POST:       icu-jobs-forum@xxxxxxxxxx
-----------------------------------------------------------


-----------------------------------------------------------
To subscribe/unsubscribe: 
        Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
        with a subject of subscribe or unsubscribe

To view the archives of this list please login at http://www.freelists.org.
Our list name is icu-pcb-forum or go to
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
        Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx

Want to post a job listing ?  DON'T DO IT HERE!  
Better yet, join our jobs listing forum.

SUBSCRIBE:  icu-jobs-forum-subscribe@xxxxxxxxxx
POST:       icu-jobs-forum@xxxxxxxxxx
-----------------------------------------------------------



-----------------------------------------------------------
To subscribe/unsubscribe: 
        Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
        with a subject of subscribe or unsubscribe

To view the archives of this list please login at
http://www.freelists.org. Our list name is icu-pcb-forum
or go to http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
        Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx

Want to post a job listing ?  DON'T DO IT HERE!  
Better yet, join our jobs listing forum.

SUBSCRIBE:  icu-jobs-forum-subscribe@xxxxxxxxxx
POST:       icu-jobs-forum@xxxxxxxxxx
-----------------------------------------------------------

Other related posts: