[duxuser] Re: dbt and everest embosser
- From: "George Bell" <george@xxxxxxxxxxxxxxxxxxx>
- To: <duxuser@xxxxxxxxxxxxx>
- Date: Sat, 20 Jan 2007 19:34:13 -0000
It all depends on paper size. For example, 12 inch deep
paper on an Index will usually allow a maximum of 29 lines
single-sided. Consequently if you have a top margin of one
line, and 29 lines per page, only 28 lines of braille will
fit on to the page. If there is a 29th line, it will
overflow on to the second page.
________________________________
From: duxuser-bounce@xxxxxxxxxxxxx
[mailto:duxuser-bounce@xxxxxxxxxxxxx] On Behalf Of Armando
Maldonado
Sent: 20 January 2007 19:27
To: duxuser@xxxxxxxxxxxxx
Subject: [duxuser] Re: dbt and everest embosser
so by doing this, will teh brialle run over the bottom
margin? That's what I'm afraid of. Thanks.
Armando
----- Original Message -----
From: George Bell
<mailto:george@xxxxxxxxxxxxxxxxxxx>
To: duxuser@xxxxxxxxxxxxx
Sent: Saturday, January 20, 2007 11:22 AM
Subject: [duxuser] Re: dbt and everest embosser
Oops, sorry. The same principal applies though. 26
lines + 1 for Top Margin means allowing for 27 lines in
total on the page.
________________________________
From: duxuser-bounce@xxxxxxxxxxxxx
[mailto:duxuser-bounce@xxxxxxxxxxxxx] On Behalf Of Armando
Maldonado
Sent: 20 January 2007 19:19
To: duxuser@xxxxxxxxxxxxx
Subject: [duxuser] Re: dbt and everest embosser
the top margin is est at 1.
----- Original Message -----
From: George Bell
<mailto:george@xxxxxxxxxxxxxxxxxxx>
To: duxuser@xxxxxxxxxxxxx
Sent: Saturday, January 20, 2007 11:16 AM
Subject: [duxuser] Re: dbt and everest
embosser
Hi Armando,
If you have a binding margin of 3 cells, and
30 cells per line, you will have to allow for 33 cells in
total per line.
Try reducing your characters per line to 28
or 29.
Likewise, if you have a top margin a 3 lines
and wish to print 26 lines, you will need to allow for a
total of 29 lines.
George.
________________________________
From: duxuser-bounce@xxxxxxxxxxxxx
[mailto:duxuser-bounce@xxxxxxxxxxxxx] On Behalf Of Armando
Maldonado
Sent: 20 January 2007 19:08
To: duxuser@xxxxxxxxxxxxx
Subject: [duxuser] dbt and everest embosser
Hello Members,
I'm using dbt 10.6 with an everst embosser
version II. For some reason, I cannot get dbt to work
properly with the embosser. What happens is that the page
number appears on the second line rather than on the right
side of page, and the braille goes over the margin. I have
set the embosser to characters per line at 32, left margin,
b margin, top margin and bottom margin all to zero. The
lines per page is set at 26. In DBT, I have it set to the
following: characters per line, 30, binding margin 3, top
margin 1, right most placement cell at 32. If you can please
tell me what I need to change in order for the two to
communicate properly, this would be appreciated. Thanks.
Armando
________________________________
No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.432 / Virus Database:
268.16.10/625 - Release Date: 1/13/2007 5:40 PM
________________________________
No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.432 / Virus Database: 268.16.10/625 -
Release Date: 1/13/2007 5:40 PM
Other related posts:
