[duxhelp] Re: For Autobuild users only.
- From: "Jack Maartman" <jmaartman@xxxxxxxxxxx>
- To: <duxhelp@xxxxxxxxxxxxx>
- Date: Fri, 28 May 2004 20:04:05 -0700
Hi George:
I tried setting up and removing some embossers to gage where the Blazer
would be on the list. I was not allowed to remove any. When I changed the
top margi from 0 to 2, I received the message
Paraphrase: Dbt had made the appropriate adjustments, which would profoundly
effect any further embossing. Hiowever when I went in again, it was zero as
your prediction.
With 12 inch paper, values you stated in effect, DBT verified the values had
been excepted, but in its wisdom changed the top margin to one.
Would you like me to try this in the old dbt for dos.
Apart from a more elaborate confirmation message, I replicated your results.
Hope this helps
Jack
----- Original Message -----
From: "George Bell" <george@xxxxxxxxxxxxxxxxxxx>
To: <duxhelp@xxxxxxxxxxxxx>
Sent: Friday, May 28, 2004 4:56 PM
Subject: [duxhelp] For Autobuild users only.
> If you are not on the Untested Autobuild access list, and if you have a
> build earlier than 28th May, please ignore this message.
>
> If you DO have the autobuild of 18th May or later, I really would be
> grateful if you could PLEASE take a few minutes to try these steps.
>
> 1) Go to Global Embosser Setup.
>
> 2) Select "New".
>
> 3) In the General Tab, where it now says, "(Please select a model)",
> scroll down and select "Freedom Scientific Braille Blazer".
>
> 4) Click on OK. (Which will return you to the main dialog.
>
> 5) If you happen to have other embossers set up, is the highlight on,
> "Freedom Scientific Braille Blazer", or something else? In my case,
> focus seems to be always on the SECOND in the list, NOT on the newly
> created Device.
>
> 6) Highlight the new device anyway. Does Form go to "Narrow Width, 10
> Inch Long, Braille Paper"?
>
> 7) Regardless of above, note setting of Lines per page. 10 inch shows
> 24 Lines.
>
> 8) Now look at Top Margin, which should be zero, and enter a figure of
> two, and click O.K.
>
> 9) A warning comes up. Does it say, "Old Format" 2, and "New Format"
> zero?
>
> 10) Click OK to accept, and return to DBT.
>
> 11) Go back to Global Embosser Setup, select the above embosser, and
> tell me what the Top Margin is set to? (Remember, we entered "2"
> previously. On my system it comes back as Zero.
>
> Fine, but we're not finished yet.
>
> 12) With the above embosser selected, change the form to, "Narrow
> Width, 12 inch Long, Braille Paper"
>
> 13) Note that Lines per page is now 28, and that we have a Top Margin
> of Zero.
>
> 14) Change Top Margin in Lines from Zero again to 2, and press OK.
>
> 15) Warning comes up. Is it Old Format 2 - New Format 1? Click on OK.
> Dialog closes.
>
> 16) Back into embosser Setup again and select the same Device. Is
> Lines per page still 28, and has Top Margin become 1 (One)? But did we
> not enter 2?
>
> Now I have done this on two separate downloads, and on two separate
> machines and operating systems (XP Home and Pro) and I get the same
> results.
>
> George Bell.
>
>
>
>
>
>
>
>
>
> This Message has been scanned for viruses by McAfee Groupshield.
> * * *
> * This message is via list duxhelp at freelists.org.
> * To unsubscribe, send a blank message with
> * unsubscribe
> * as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also
> * subscribe, unsubscribe, and set vacation mode and other subscription
> * options by visiting //www.freelists.org. The list archive
> * is also located there.
> * Duxbury Systems' web site is http://www.duxburysystems.com
> * * *
* * *
* This message is via list duxhelp at freelists.org.
* To unsubscribe, send a blank message with
* unsubscribe
* as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also
* subscribe, unsubscribe, and set vacation mode and other subscription
* options by visiting //www.freelists.org. The list archive
* is also located there.
* Duxbury Systems' web site is http://www.duxburysystems.com
* * *
Other related posts:
