[ddots-l] Re: Bank/Patch Changes Not Matching Up
- From: "Kevin L. Gibbs" <kevjazz@xxxxxxx>
- To: <ddots-l@xxxxxxxxxxxxx>
- Date: Mon, 2 Oct 2006 09:04:09 -0700
I suspect the problem is in the Krog, not in Sonar. Thre must see some
setting that isn't correct. Are you in the U.S.? Krog's Tech Support
number on the East Coast is:
1-516-333-8737.
Kevin
-----Original Message-----
From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx]
On Behalf Of Kim Ellsworth
Sent: Monday, October 02, 2006 4:35 AM
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Re: Bank/Patch Changes Not Matching Up
Hi Tim,
Thanks for writing and for trying to help. It is an exact match for
the
Triton Extreme found at the Korg forum site. There were actually two
different .INS files there for the Triton Extreme, one was minus the
drum kits. I have even looked through the .INS file in Notepad and the
instruments do match up.
I am sure this must be something simple that I just haven't hit on yet
and hopefully someone can help me get to the bottom of it. If you or
anyone has any further questions please let me know. Thanks again to
everyone who is trying to help here.
With her fingers crossed,
Kim Ellsworth
-----Original Message-----
From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx]
On Behalf Of Tim Burgess
Sent: Monday, October 02, 2006 3:36 AM
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Re: Bank/Patch Changes Not Matching Up
Hi,
Just checking - within the Korg.ins file, was there an exact match for
your synth or did you take an approximation?
Best wishes.
Tim Burgess
Raised Bar Ltd
Phone: +44 (0)1827 719822
Don't forget to vote for change at http://www.raisedbar.net/petition.htm
-----Original Message-----
From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx]
On Behalf Of Kim Ellsworth
Sent: 02 October 2006 00:30
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Bank/Patch Changes Not Matching Up
Hi everyone,
Please, please help me! I no I almost have everything setup properly
between my synthesizer (Korg Triton Extreme), my sound card (M-Audio
Delta LT 1010) and my desktop computer. I've read and read the Cake
Talking tutorial on the subject of midi, hardware setup, etc. until I'm
blue in the face. I'm so close, yet still so far from being able to
start recording.
Situation:
1. Currently, my Korg is connected to the desktop via two routes; via
USB to the computer(we were told to do this by the dealer where we
bought the
synthe) and by two midi cables (input and output of course that go
directly to the sound card).
2. Right now, until I can get a mixer, I have a set of monitor speakers
to listen to the synthesizer through. 3. I am running Sonar 4, producer
edition and Cake Talking 4.0.3. OS on desktop machine is Windows XP
Home, SP2.
4. I followed the instructions on configuring Sonar to recognize the
Delta 1010, ran the Cake Talk tests at the beginning of this whole setup
and everything was successful.
5. I imported the korg.ins file in the import instrument deffinitions
dialog and that appeared successfull as the patch names for the banks in
the program and combi mode show up properly when choosing patch names.
However, when I cycle through the patch names after choosing a bank via
Sonar, the sounds do change on the synthe side but it's not the correct
patch; rather, no matter what bank I choose and what patch I choose via
sonar, it is only picking the synthesizer's general midi patch sounds
and not the sounds that are specific to the Korg. Example, in Sonar, I
choose Bank a, Patch name keyboard piano and strings. This is a patch
that on the actual synthesizer does indeed belong to bank A. Yet, the
synthe switches to harpsichord instead. Am I making sense?
By the way, Local Mode is set to off, enable bank, program and combi
changes are all turned on. I played around a bit with the input and
output of midi ports but currently I have the input set to the Delta and
the output set to USB audio device, which is how my Korg shows up in
Sonar and in the midi devices in my sounds and audio properties of my
computer.
I apologize for making this a novel but trying to give as much
information as possible that may be of some help and also, I've been
working on trying to get this setup for a while now and a bit frustrated
that I cannot figure this thing out on my own.
Kind Regards,
Kim Ellsworth
** To leave the list, click on the immediately-following link:-
** [mailto:ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe]
** If this link doesn't work then send a message to:
** ddots-l-request@xxxxxxxxxxxxx
** and in the Subject line type
** unsubscribe
** For other list commands such as vacation mode, click on the
** immediately-following link:-
** [mailto:ddots-l-request@xxxxxxxxxxxxx?subject=faq]
** or send a message, to
** ddots-l-request@xxxxxxxxxxxxx with the Subject:- faq
__________ NOD32 1.1786 (20061002) Information __________
This message was checked by NOD32 antivirus system. http://www.eset.com
** To leave the list, click on the immediately-following link:-
** [mailto:ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe]
** If this link doesn't work then send a message to:
** ddots-l-request@xxxxxxxxxxxxx
** and in the Subject line type
** unsubscribe
** For other list commands such as vacation mode, click on the
** immediately-following link:-
** [mailto:ddots-l-request@xxxxxxxxxxxxx?subject=faq]
** or send a message, to
** ddots-l-request@xxxxxxxxxxxxx with the Subject:- faq
** To leave the list, click on the immediately-following link:-
** [mailto:ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe]
** If this link doesn't work then send a message to:
** ddots-l-request@xxxxxxxxxxxxx
** and in the Subject line type
** unsubscribe
** For other list commands such as vacation mode, click on the
** immediately-following link:-
** [mailto:ddots-l-request@xxxxxxxxxxxxx?subject=faq]
** or send a message, to
** ddots-l-request@xxxxxxxxxxxxx with the Subject:- faq
Other related posts:
