[THIN] Re: Xen Server Issue
- From: Andy Friar <Andy.Friar@xxxxxxxxxxx>
- To: "thin@xxxxxxxxxxxxx" <thin@xxxxxxxxxxxxx>
- Date: Thu, 18 Aug 2011 09:15:38 +0000
It would depend on your switch configuration.
If the switch is set to untagged vlan 1, then you wouldn't need to tag
"internal" in fact you would just use "Network 1"
If the switch port is setup as untagged vlan 5 or untagged no vlan and tagged
vlan 1 then "Internal" would work correctly.
Hth
Andy
From: thin-bounce@xxxxxxxxxxxxx [mailto:thin-bounce@xxxxxxxxxxxxx] On Behalf Of
Hamilton, Ronnie
Sent: 18 August 2011 08:35
To: thin@xxxxxxxxxxxxx
Subject: [THIN] Re: Xen Server Issue
Joe,
So If Im reading this correctly I need to set up the physical switch port with
the TAG number of the Virtual network from the XenServer.
[cid:image001.jpg@01CC5D8F.C6D3AF50]
So I have two NIC in server NIC 0 for management and NIC 1 for server traffic.
I set up virtual network Internal on NIC 1 which has a VLAN ID of 1, dos this
meen that VLAN port on the switch mush have a TAG for Vlan 1.
As I thought it was default VLAN of 1 was already on the switch and I couldn't
get the server to talk on his Internal network at all.
Maybe I need to be using a different VLAN ID that's not in use on out network
already.
Ronnie
From: thin-bounce@xxxxxxxxxxxxx [mailto:thin-bounce@xxxxxxxxxxxxx] On Behalf Of
Joe Shonk
Sent: 17 August 2011 16:35
To: thin@xxxxxxxxxxxxx
Subject: [THIN] Re: Xen Server Issue
It's all in the networking, not Xen. Just use Network 1 if that's all that is
going to be used. If you plan on tagging vLans then you will want to setup a
new connection as well as configure the switch-port for such.
Joe
From: thin-bounce@xxxxxxxxxxxxx [mailto:thin-bounce@xxxxxxxxxxxxx] On Behalf Of
Hamilton, Ronnie
Sent: Wednesday, August 17, 2011 8:23 AM
To: thin@xxxxxxxxxxxxx
Subject: [THIN] Xen Server Issue
All,
I have set up XenServer on a single box for some testing of Access gateway VPX.
I also have a server 2008 instaled.
I have two NIC's with an extra ordered.
I have NIC 0 set as management with IP address and this works fine.
The second NIC I have plugged into our internal LAN, when I create a Network
and select NIC 1 and then select this Virtual Network in my 2k8 server I cannot
get network connectivity.
When I select the Network 1 which is the built in NIC 1 directly all works fine.
Seem to be going round in circles is this possible with XenServer and Xen
Centre free edition.
Thanks
Ronnie
Ronnie Hamilton
Senior Network Engineer
Lufthansa Technik Airmotive Ireland
IT Department
Naas Road, Rathcoole
Co. Dublin, Ireland
Phone: +353 1 401 1253
E-mail: ronnie.hamilton@xxxxxxx<mailto:ronnie.hamilton@xxxxxxx>
www.ltai.ie<http://www.ltai.ie>
Visit our website : www.ltai.ie<http://www.ltai.ie>
__________________________________________
Lufthansa Technik Airmotive Ireland Limited. Registered in Ireland. Reg. No.
45999. Registered Office: Naas Road, Rathcoole, Co.Dublin.
Lufthansa Technik Airmotive Ireland Leasing Limited. Registered in Ireland.
Reg. No. 140891. Registered Office: Naas Road, Rathcoole, Co.Dublin.
__________________________________________
The information in this email and in any attachments is confidential and may be
privileged. If you are not the intended recipient, please destroy this message,
delete any copies held on your systems and notify the sender by return email.
You should not read, retain, copy, disseminate, distribute, disclose or use
this email or its contents in any way. Any such action is strictly prohibited.
Thank you.
Other related posts:
