With Zenith, the first three modules you get are going to be bad, if you order factory rebuilts. Russ Hoyt Hoyt's TV Exeter, NH ----- Original Message ----- From: "William Dravenstott" <cdravens@xxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Thursday, March 04, 2004 12:06 AM Subject: [TechAssist] Re: Zenith projo looses convergence pulses > Tim, > I fixed mine today the blue reg ic was bad as it loaded. My thought > was probably you got a bad module? Just a thought been there and done that. > Bill Dravenstott > Elza's Home Store > 924 Union Street > Ashland, OH 44805 > ----- Original Message ----- > From: "Tim Poole" <tdp13158@xxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Tuesday, March 02, 2004 11:45 PM > Subject: [TechAssist] Re: Zenith projo looses convergence pulses > > > > I tried the convergence board with no luck. I am in the process of trying > to > > get the print on the set after replacing both convergence 9-1318 and sweep > > 9-1302-07. Ill let you know what I find when I finish. Let me know if you > > finish before I do. Thanks, Tim > > ----- Original Message ----- > > From: "William Dravenstott" <cdravens@xxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Wednesday, March 03, 2004 1:35 AM > > Subject: [TechAssist] Re: Zenith projo looses convergence pulses > > > > > > > Tim > > > Did you resolve your problem? I have one doing a similar thing. > The > > > source voltages check good, suspect a bad STK after it gets hot it > starts > > > the shift. If I unplug the blue convergence it stays ok on others. > > Afraid > > > problem may be on the convergence board. Customer reluctant to spend > much > > > so I am doing little until I get an ok to proceed. > > > Bill Dravenstott > > > Elza's Home Store > > > 924 Union St > > > Ashland, OH 44805 > > > ----- Original Message ----- > > > From: "Tim Poole" <tdp13158@xxxxxxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Wednesday, February 25, 2004 10:56 PM > > > Subject: [TechAssist] Zenith projo looses convergence pulses > > > > > > > > > > I am working on a Zenith projo that begins to pulse with loss of > > > convergence correction after it has been on about 15 minutes. I have > > > replaced the 9-1302-7 deflection and the 9-1318-2a convergence board > with > > no > > > results. Anyone seen this? Weird! > > > > Tim Poole pooletim@xxxxxxxxxxx tdp13158@xxxxxxxxxxx > > > > dba A-Mobile TV Shop & Precision TV Service > > > > 17626 Shady Lane > > > > Fredericktown, Ohio 43019 > > > > 419-756-3443 > > > > 740-694-8585 > > > > fax 740-694-1032 > > > > > > > > > > > -------------------------------------------------------------------------- > > > --- > > > > Lost Password: > > > > http://www.tech-assist.org and select "Login Problems?". > > > > Email Archives: > > > > //www.freelists.org/archives/techassist/ > > > > > > > > > > > > > > -------------------------------------------------------------------------- > > --- > > > Lost Password: > > > http://www.tech-assist.org and select "Login Problems?". > > > Email Archives: > > > //www.freelists.org/archives/techassist/ > > > > > > > > > -------------------------------------------------------------------------- > --- > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > > > -------------------------------------------------------------------------- --- > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ > ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/