Change the STK's and check the one ohm resistors in front of them. From Tech Repair CD: Zenith\50Z83R8 \picture looks like convergence is turned off (which it is) and is bouncing vertically\\\9-1674 sweep 9-1690 convergence\found flyback winding from pin 6 to 10 open resulting in no 16 volts. + & - 26 were good\\\\\\\\ Zenith\9-1690\1 Ohm Resistors Smoke On Convergence Module\\\9-1690\The 5a Pigtail Fuses On The Main Ps/Sweep Board May Be Open...Check Them\\\\\\\\ ZENITH \A50M91W9 9-1978\Convergence/ Bent Lines In Pic/ Resistors Burnt On Convergence Board\\\9-1690 9-1978\Cr3419 Shorted And Fx3460 Blown Replaced Burned Resistors On Convergence Board R4161 & R1460\check resistors R3243 (110K) and R3244 (82K) on the 9-1978 module\\\\\\\ Zenith\A56M91W9\Defection bowed top and bottom* convergence out and crosshairs do not move.\\\Sweep module 9-1978 Registration module 9-1690\Replace both Convergence amps* IC4008 and IC4009* both STK392-110* and up to four open 1 ohm 1/2 watt resistors near the IC's* R4060 thru R4063.\All caps nearby checked ok. Convergence returned to normal with little adjusting needed.\\\\\\\ Zenith\PVR4660VK\Pix is bowed equally on top* bottom* and sides* and convergence is bad\\\9-1690 9-1674\Doing a complete convergence alignment on this set* fixed the problem. The key was to adjust the Vertical and Horz size pots on the sweep module\by using the green CRT only* before starting the more traditional convergence procedure. Once you have a good* straight looking cross hatch pattern for the green\it is much easier to go ahead and converge the Red* and the Blue to the established green pattern. You have to adjust for a 3 : 4 display on your cross hatch generator.\(3 vertical squares for every 4 horizontal squares ). The actual number of Vert & Horz squares for each signal generator will vary\Once you set the main size pots* check a channel that has graphics at the bottom or top and make sure it is not being clipped off\\\\ Zenith\PVY4662DT\Convergence way off- no control of convergence\\\9-1690\R4151M (1k SMD) open off pin 3 of plug 3C8 on 9-1690 convergence module\\\\\\\\ Jeff -- Intrepid Video TV/VCR Repair 263 S Front St, Steelton PA 17113 717-939-7708; (F) 717-564-4952 www.intrepid-video.com www.tech-repair.net ----- Original Message ----- From: "Jamie" <mayj@xxxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Tuesday, August 10, 2004 12:32 PM Subject: [TechAssist] Zenith PVY5263DT bad convergence swps/swp 9-1674 conv 9-1690 Changed bad bleeder assembly A-17196-12. Now set turns on w/ picture but bad convergence & green is jittery. Unplug green conv.& green picture is steady. R3243 & R3244 ck. good. I have +26, -26, & +15v to conv. bd. Is there supposed to be a -15v going to this bd. & if so where? Just want to make sure I have all supply voltages to the bd. before changing the STK's. Thanks Jamie Affordable TV Repair ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/