Shaun, I don't think that is your problem, the block. I have ran in to that problem several times. I have yet to figure it out, just get another 9-1978 board. If you figure it out please let me know Thank. Avery Avery Boyd 4666B S. Mingo Tulsa OK 74146 Phone 918-665-2400 ----- Original Message ----- From: "Shaun" <satguy@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Wednesday, June 01, 2005 12:30 PM Subject: [TechAssist] Re: Zenith A60M91W1 with 9-1978 module no pix after 10 minutes The convergence module looks like new no discolored resistors and solder looks good. My thoughts are either the 9-1978 or the hv divider but I want to try and see which one first. I am going to put the 9-1978 in my personal tv and see how long it runs if it runs good I will replace the hv divider. Shaun Advanced Electronics 224 West Riverview Ave. Fort Morgan, CO 80701 ----- Original Message ----- From: "John @ Myers TV " <myers_tv_b@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Tuesday, May 31, 2005 9:13 PM Subject: [TechAssist] Re: Zenith A60M91W1 with 9-1978 module no pix after 10 minutes > Shaun, > > I just did one that would lose HV after about 30 seconds. Not the > original problem, I might add. > I went through 3 boards before finding a good one. > But, how's the convergance board? any sign of discoloration on the > fusible resistors? > > John Myers > Myers TV Service Co. > 376 E. State St. > Alliance, OH 44601 > > Voice / Fax: 330-821-6545 > Myers_tv_b@xxxxxxxxxxxxx > http://www.myerstv.net > > Work as if you were to live a hundred years, > Pray as if you were to die tomorrow. > Ben Franklin > > > > > Shaun wrote: > > >This set will run for 10-15 minutes and then the picture goes out. Set > >looses high voltage but still has sound. I removed the 9-1978 which was > >replaced about a year ago. I soldered all the normal places that go bad and > >really never found any problems. If I let it sit for about 10 minutes > >unplugged then plug it back in it will run again for about 10-15 minutes > >again. I tapped around on the 9-1978 and the set never changes. The HV block > >measures 50K and the convergence module shows no sign of problems. Any idea > >from anyone out there? > > > >Shaun > > > >Advanced Electronics > >224 West Riverview Ave. > >Fort Morgan, CO 80701 > > > >--------------------------------------------------------------------------- -- > >This Email List is Public. Remove: http://www.tech-assist.org/remove.htm > >Lost Password: http://www.tech-assist.org and select "Login Problems?". > >Appliance Repair List: http://www.tech-assist.org/secure/tip/chatjoin.htm#app > >Email Archives: //www.freelists.org/archives/techassist/ > > > > > > > > > -------------------------------------------------------------------------- --- > This Email List is Public. Remove: http://www.tech-assist.org/remove.htm > Lost Password: http://www.tech-assist.org and select "Login Problems?". > Appliance Repair List: http://www.tech-assist.org/secure/tip/chatjoin.htm#app > Email Archives: //www.freelists.org/archives/techassist/ ---------------------------------------------------------------------------- - This Email List is Public. Remove: http://www.tech-assist.org/remove.htm Lost Password: http://www.tech-assist.org and select "Login Problems?". Appliance Repair List: http://www.tech-assist.org/secure/tip/chatjoin.htm#app Email Archives: //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- This Email List is Public. Remove: http://www.tech-assist.org/remove.htm Lost Password: http://www.tech-assist.org and select "Login Problems?". Appliance Repair List: http://www.tech-assist.org/secure/tip/chatjoin.htm#app Email Archives: //www.freelists.org/archives/techassist/