[TechAssist] Re: RCA M# F35673MB CH# CTC187CL3
- From: "al m" <ampm@xxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Tue, 16 Dec 2003 15:42:48 -0500
Glad to help, did that twice myself. The second time I knew I saw it before
but it still took me a little while to remember where.
Al Marquardt
ampm@xxxxxxx
Al Marquardt Electronic Repair
206 W Main
Girardville Pa. 17935
----- Original Message -----
From: "Webster TV" <webstertv@xxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Tuesday, December 16, 2003 2:12 PM
Subject: [TechAssist] Re: RCA M# F35673MB CH# CTC187CL3
> Al,
>
> Thanks a million, that was the problem, soon as I read your suggestion, I
> remembered unplugging it to give me more room to install the wires from
the
> flyback. Just forgot to reinstall the plug, live and learn.Thanks again
you
> saved me allot of time trying to run the problem down.
>
> Dan Webster
> ----- Original Message -----
> From: "al m" <ampm@xxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Tuesday, December 16, 2003 12:08 PM
> Subject: [TechAssist] Re: RCA M# F35673MB CH# CTC187CL3
>
>
> > Make sure you have the ground wire on the CRT board plugged in.
> > Al Marquardt
> > ampm@xxxxxxx
> > Al Marquardt Electronic Repair
> > 206 W Main
> > Girardville Pa. 17935
> > ----- Original Message -----
> > From: "Webster TV" <webstertv@xxxxxxx>
> > To: <techassist@xxxxxxxxxxxxx>
> > Sent: Tuesday, December 16, 2003 11:48 AM
> > Subject: [TechAssist] RCA M# F35673MB CH# CTC187CL3
> >
> >
> > > Techs,
> > >
> > > This set had a bad flyback and shorted HOT originally, there was
> > > discoloration around the HOT on the board, so presumed HOT had been
> > running
> > > hot, replaced flyback, HOT, H. Driver Transformer, caps C4306, C4407,
> and
> > > diode CR4403.Resistors R4110, R4126, R4305 that were stressed
> > (discolored ),
> > > also replaced resistor R4402 in HOT circuit. Checked all voltage
> supplies
> > > and they are all real close. Set now operates fine, HOT runs cool, but
> on
> > > pictures that have writing on the screen or writing scrolling along
> > bottom,
> > > the letters are bent or kinked, you can also notice a slight kink or
> bend
> > in
> > > vertical straight edges, like doorways,etc.This problem looks like a
> > > capacitor problem, but I haven't run into this problem before, I
checked
> > > tech-assist tips and found nothing that seemed close to this problem.
> > Anyone
> > > seen this before or have a solution?
> > >
> > > Dan Webster
> > > Webster's TV
> > > Shullsburg, Wi.
> > >
> > >
> >
>
****************************************************************************
> > *
> > > Lost Password:
> > > http://www.tech-assist.org and select "Login Problems?".
> > > Email Archives:
> > > //www.freelists.org/archives/techassist/
> > >
> > >
> >
> >
> >
>
****************************************************************************
> *
> > Lost Password:
> > http://www.tech-assist.org and select "Login Problems?".
> > Email Archives:
> > //www.freelists.org/archives/techassist/
> >
>
>
****************************************************************************
*
> Lost Password:
> http://www.tech-assist.org and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/
>
>
*****************************************************************************
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
Other related posts:
