I have disks on my wish list. On Nov 17, 2011, at 5:05 PM, sammie smith <bugcollections@xxxxxxxxxxxxx> wrote: > Knock on wood, I have never had that problem. It just seems that the > cylinders are prone to leak a lot more than they should. I would think > cylinders, both wheel and master, should last a lot longer than they do. > > --- On Thu, 11/17/11, Denis Dodson <coocoo@xxxxxxx> wrote: > > From: Denis Dodson <coocoo@xxxxxxx> > Subject: [tcb] Re: repair story > To: tcb@xxxxxxxxxxxxx > Date: Thursday, November 17, 2011, 4:57 PM > > It’s the treading where the line goes to the cylinders. I could not get a > good thread no matter how I tried. Had to take off the cylinder, thread in > the line and put the cylinder back on the backing plate and I used plumbers > tape. I don’t know that the tape is a good idea in an automotive use, but it > did stop the leak. > > > > From: tcb-bounce@xxxxxxxxxxxxx [mailto:tcb-bounce@xxxxxxxxxxxxx] On Behalf Of > sammie smith > Sent: Thursday, November 17, 2011 4:00 PM > To: tcb@xxxxxxxxxxxxx > Subject: [tcb] Re: repair story > > > > Well, I don't know what causes so many brake cylinder leaks in the old > busses. I have changed so many wheel and master cylinders on my busses I > think I could do it in my sleep. The current leak, lower cylinder on the > left, is not more than 3 years old. About 3 years ago I rebuilt the entire > front brakes on that thing with all new cylinders. > > > > I heard that Steve Chamberlain is an expert on the split bus brake systems. > Maybe he has some ideas. > > --- On Thu, 11/17/11, Eric Woodall <ericthomaswoodall@xxxxxxx> wrote: > > > From: Eric Woodall <ericthomaswoodall@xxxxxxx> > Subject: [tcb] Re: repair story > To: "tcb@xxxxxxxxxxxxx" <tcb@xxxxxxxxxxxxx> > Date: Thursday, November 17, 2011, 8:20 AM > > I've got the same problem currently Sammie, which is the reason I haven't > driven it in a while. > > On Nov 16, 2011, at 3:24 PM, sammie smith <bugcollections@xxxxxxxxxxxxx> > wrote: > > There's always something wrong with the old busses. I drove the panel van to > the VW club meeting the other night and the front brakes were pulling hard to > the right. OK, got a chance to look at it this morning; sure enough wheel > cylinder leak on the left had given the shoes a good coating of brake fluid. > Order two new cylinders. Will be here in a couple of days. It's always > something to keep them happy. > > --- On Wed, 11/16/11, Denis Dodson <coocoo@xxxxxxx> wrote: > > > From: Denis Dodson <coocoo@xxxxxxx> > Subject: [tcb] repair story > To: tcb@xxxxxxxxxxxxx > Date: Wednesday, November 16, 2011, 12:23 PM > > So, I have gone back to work, painting apartments and condos and houses for a > rental management company and Murray is my work truck. He loves it and he > goes to work every day, but he started a miss and a hesitation from a > standing start and got worse soon. I cleaned my points with a little > sandpaper and it seemed to run a little better, but still bad. I changed my > spark plugs, I put in new set of points that was in my tool box. No joy. I > bought and put in Petronix ignition (because I hated setting the gap on the > points) and set my timing and still I had a miss. It wasn’t sporadic anymore > it was a steady power loss. > > > > OK. Not the coil, no cracked dizzy cap, rotor OK, new ignition, new plugs, > what the hell, I’ll change the spark plug wires. In doing so I couldn’t get > one old one to come out. I had disconnected it at the dizzy and at the plug, > but it wouldn’t pull free. > > > > I had changed my alternator months ago and, apparently, when I put the top > shroud back on, I pinched the wire between the shroud tin and the head tin. > What an idiot. > > > > I lopped off the old one and put in the new wire and… Murray runs like a > rocket. > > > > Isn’t it a great satisfaction when you solve a problem and your bus runs well > after? > > > > > >