[gulfrre] Re: TV en Linux

  • From: "Entrepreneur Andrés L. Sclippa" <asclippa@xxxxxxxxx>
  • To: gulfrre@xxxxxxxxxxxxx
  • Date: Fri, 12 May 2006 20:13:49 -0300

Gulfrre Grupo de Usuarios de Linux Facultad Regional Resistencia
----------------------------------------------------------------Marcos,

puedo ir probando levantando el modulo bttv con distintos valores de card, 
pero como hago para probar rapidamente si funciona?

Alguna herramienta CLI ?

---- dmesg ----
Linux video capture interface: v1.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 17, latency: 32, mmio: 0xdcdfe000

>>> bttv0: using:  *** UNKNOWN/GENERIC ***  [card=0,autodetected] <<<

bttv0: gpio: en=00000000, out=00000000 in=00f9807f [init]
tveeprom 0-0050: Huh, no eeprom present (err=-121)?
bttv0: using tuner=-1
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... found
bttv0: registered device video0
bttv0: registered device vbi0



On Friday 12 May 2006 6:29 pm, Marcos Ibanez wrote:
> Gulfrre Grupo de Usuarios de Linux Facultad Regional Resistencia
>
> ----------------------------------------------------------------On 5/12/06, 
Entrepreneur Andrés L. Sclippa <asclippa@xxxxxxxxx> wrote:
> > Gulfrre Grupo de Usuarios de Linux Facultad Regional Resistencia
> > ----------------------------------------------------------------La placa
> > que tengo es
> >
> > Brooktree Corporation Bt878 Video Capture
> >
> > Pero no esta reconocida.
>
> Especificamente que significa que no esta reconocida?
> Que distro tenes?
>
> > Alguien la conoce y la pudo instalar?
>
> Si mal no recuerdo ese es el chipset que mejor anda en linux junto con
> en bt848.
> Y para configurarlos variara dependiendo de la distro que uses, pero
> casi seguro va a haber en el proceso una recompilacion del kernel.
>
> > On Friday 12 May 2006 12:44 pm, Agustin.PHP Casiva wrote:
> > > El tema pasa que esa placa usa el chip saa7133, el soporte para esa
> > > placa
> > >
> > > esta en el modulo saa7135, que soprta desde el chip saa7130 hasta
> > > saa7135. El saa7133 no estaba muy bien soportado en la serie 2.4 del
> > > kernel. Recien en las ultimas releases del 2.6 lo soporta.
> > >
> > > Yo esta peleando con un 2.4.
> > >
> > > Lo que no hice funcionar fue el soporte para sonido, pero lo solucione
> > > conectado la salida de audio de la propia placa capturadora a la
> > > entrada del microfono de la placa de audio y de 10
> > >
> > > Saludos
> >
> > --
> > Muchas gracias y saludos cordiales.
> >
> > Atentamente,
> >
> > Andrés L. Sclippa
> > Entrepreneur
> > Ing. en Sistemas de Información
> > Guise 1944 1ro B. Buenos Aires (C1425DPH). Argentina
> > Teléfono fijo: +54 11 4826-2960
> > Teléfono móvil:  +54 11 15 4986-1967
> > Fax: +54 11 5258-2713
> > Email: asclippa@xxxxxxxxx
> > Web personal: www.AndresSclippa.com.ar
> >
> > "ESTE MENSAJE ESTA DIRIGIDO A SU DESTINATARIO UNICAMENTE. EL MISMO PUEDE
> > CONTENER INFORMACIÓN CONFIDENCIAL AMPARADA COMO TAL POR LEY. Si usted no
> > es el destinatario de este mensaje, ni la persona responsable de entregar
> > el mensaje a su destinatario, queda usted notificado de que está
> > estrictamente prohibido divulgar, distribuir o copiar este mensaje. Si
> > usted ha recibido este mensaje por error, por favor inmediatamente
> > proceda a notificar al remitente por e-mail o por teléfono y a eliminar
> > el mensaje original de su sistema.
> >
> > THIS MESSAGE IS INTENDED ONLY FOR THE USE OF THE INDIVIDUAL OR ENTITY TO
> > WHICH IT IS ADDRESSED AND MAY CONTAIN INFORMATION THAT IS RIVILEGED,
> > CONFIDENTIAL, AND EXEMPT FROM DISCLOSURE UNDER APPLICABLE LAW.  If the
> > reader of this message is not the intended recipient, or the employee
> > or agent responsible for delivering the message to the intended
> > recipient, you are hereby notified that any dissemination, distribution,
> > forwarding, or copying of this message is strictly prohibited. If you
> > have received this message in error please notify the sender immediately
> > by e-mail or telephone and delete the original message immediately."
> >  Para administrar tu cuenta: //www.freelists.org/list/gulfrre
> >  Para ver mensajes anteriores: //www.freelists.org/archives/gulfrre
> >  -----------------------------------------------------------------------

-- 
Muchas gracias y saludos cordiales.

Atentamente,

Andrés L. Sclippa
Entrepreneur  
Ing. en Sistemas de Información
Guise 1944 1ro B. Buenos Aires (C1425DPH). Argentina
Teléfono fijo: +54 11 4826-2960
Teléfono móvil:  +54 11 15 4986-1967
Fax: +54 11 5258-2713
Email: asclippa@xxxxxxxxx
Web personal: www.AndresSclippa.com.ar

"ESTE MENSAJE ESTA DIRIGIDO A SU DESTINATARIO UNICAMENTE. EL MISMO PUEDE
CONTENER INFORMACIÓN CONFIDENCIAL AMPARADA COMO TAL POR LEY. Si usted no 
es el destinatario de este mensaje, ni la persona responsable de entregar 
el mensaje a su destinatario, queda usted notificado de que está estrictamente
prohibido divulgar, distribuir o copiar este mensaje. Si usted ha recibido 
este mensaje por error, por favor inmediatamente proceda a notificar al 
remitente por e-mail o por teléfono y a eliminar el mensaje original de su 
sistema.

THIS MESSAGE IS INTENDED ONLY FOR THE USE OF THE INDIVIDUAL OR ENTITY TO
WHICH IT IS ADDRESSED AND MAY CONTAIN INFORMATION THAT IS RIVILEGED, 
CONFIDENTIAL, AND EXEMPT FROM DISCLOSURE UNDER APPLICABLE LAW.  If the 
reader of this message is not the intended recipient, or the employee 
or agent responsible for delivering the message to the intended 
recipient, you are hereby notified that any dissemination, distribution, 
forwarding, or copying of this message is strictly prohibited. If you 
have received this message in error please notify the sender immediately 
by e-mail or telephone and delete the original message immediately."
 Para administrar tu cuenta: //www.freelists.org/list/gulfrre
 Para ver mensajes anteriores: //www.freelists.org/archives/gulfrre
 -----------------------------------------------------------------------

Other related posts: