Re: [foxboro] WP51A Built-in Eth TP Port
- From: "Medina, Jose R" <jose.r.medina@xxxxxxxxxx>
- To: foxboro@xxxxxxxxxxxxx
- Date: Wed, 2 Mar 2005 17:08:49 -0500
I got it working. Thanks people for the reply. Specially Latheef. The
solution provided by Latheef was the most accurate that helped me. I did
the following steps.
1- Create a file /etc/hostname.le1 to include the interface new name.
2- Modify /etc/hosts to include and specify the IP address for the new
name.
3- reboot the machine
After this, the "ifconfig -a" showed both interfaces and I was able to
ping through both.
Thanks,
Jose R. Medina-Delgado - P.E.
Automation Engineer
Engineering/Process Control & Automation
Pfizer Global Manufacturing - Arecibo Site
Phone : 787.775.5421
Fax : 787.775.7030
E-Mail : jose.r.medina@xxxxxxxxxx
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx]
On Behalf Of Latheef, P.A.
Sent: Tuesday, March 01, 2005 3:36 PM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] WP51A Built-in Eth TP Port
Jose,
Check with the following commands:
ifconfig -a
Above command should give you the list of configured Ethernet ports in
the
machine
ifconfig le1 plumb
Command should create le1 if it does not exist.
ifconfig le1 inet XXX.XXX.XX.XX
where XXX.XXX.XX.XX is the IP Address, assigns the address to le1
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx]
On
Behalf Of Medina, Jose R
Sent: Tuesday, March 01, 2005 11:26 AM
To: foxboro@xxxxxxxxxxxxx
Subject: [foxboro] WP51A Built-in Eth TP Port
Hi List :
I have a WP51A ver. 4.0 running DM since a long time ago (1994). This
machine is a tiny SUN box with a built-in TP ether port and a BNC/AUI
LAN
card (not built-in).
I would like to have an additional access to this machine through the TP
port, however this machine only sees "le0" as the only eth port and it
is
pointing to the BNC/AUI Lan card. It looks like the TP port is disable
somehow from the PROM level, but I don't find a parameter for this.
Is there a way to enable or use this TP port or it is hard disabled? Is
it a
jumper on the board? How it is solved?
Thanks in advanced for any reply!
Jose R. Medina-Delgado - P.E.
Automation Engineer
Engineering/Process Control & Automation
Pfizer Global Manufacturing - Arecibo Site
Phone : 787.775.5421
Fax : 787.775.7030
E-Mail : jose.r.medina@xxxxxxxxxx
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
Other related posts:
