Thank you. All of the gbics are Avago. I will be sure to update the tool and try again. The WPs are HP Z420 series with PCI-E cards. No place to put PCI cards. I hope this was fixed. Checking my config of edge vs non edge now. Thanks. I'll get bak to you soon. Jim. Sent from my iPhone > On Jan 14, 2015, at 11:00 AM, "Boulay, Russ" > <Russ.Boulay@xxxxxxxxxxxxxxxxxxxxxx> wrote: > > We have had some reports of the vendor of the gbic could be an issue.... > We have yet to verify.... > > Check the vendor of the MGBIC (P0973JE). > Avago will work > Formerica has a problem. > > > > -----Original Message----- > From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On > Behalf Of Dwayne Landry > Sent: Wednesday, January 14, 2015 10:52 AM > To: foxboro@xxxxxxxxxxxxx > Subject: Re: [foxboro] Enterasys C5K175-25 P0973KJ Help!! > > Did you verify that the admin edge was set correctly for your 100MB ports. > Open up the CLI on the C5 switch and run the command "show spantree > adminedge" The ports that are going to end devices, CPs, AWs etc. Should be > set to edge and the uplink ports to other switches should be non-edge. > Either re-run the configuration to get it correct or you can change the admin > edge settings per port with the command "set spantree adminedge fe.1.1 true" > where the fe.1.1 represents the port that you want to set. Remember to save > your configuration when you're done. "save config" > > Thanks, > Dwayne Landry > Axiall Corp. > > -----Original Message----- > From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On > Behalf Of Jim Aster > Sent: Wednesday, January 14, 2015 10:03 AM > To: foxboro@xxxxxxxxxxxxx > Subject: [foxboro] Enterasys C5K175-25 P0973KJ Help!! > > Good morning List, > > > I am having a heck of a time trying to configure two Enterasys C5K175-25 > P0973KJ switches. I am using the configuration tool v3.5.1 with the most > recent firmware. I am also using 100 base SFP modules in all of the ports > except for the two uplink/downlink ports. I can configure the switches just > fine (so it would seem), however, when I connect several CPs to the switches > the ports activate just fine, but when I try to connect an AW or WPs the > ports do not activate. I can remove the gbic and fiber and try different > ports and occasionally I can get one to work, however, if I reboot the AW or > WP the port is no longer active. > > > > I need help with these specific switches, thank you. > > > > Any help here is greatly appreciated, > > > > Jim Aster > > Western States Controls > > > > _______________________________________________________________________ > This mailing list is neither sponsored nor endorsed by Invensys Process > Systems (formerly The Foxboro Company). Use the info you obtain here at your > own risks. Read http://www.thecassandraproject.org/disclaimer.html > > foxboro mailing list: //www.freelists.org/list/foxboro > to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join > to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave > > > > > > The information transmitted, including any attachments, is intended only for > the person or entity to which it is addressed and may contain confidential > and/or privileged material. Any review, retransmission, dissemination or > other use of, or taking of any action in reliance upon, this information by > persons or entities other than the intended recipient is prohibited, and all > liability arising therefrom is disclaimed. If you received this in error, > please contact the sender and delete the material from any computer. Axiall > Corporation (formerly known as Georgia Gulf corporation) is a Delaware > corporation. This communication may come from Axiall Corporation or one of > its subsidiaries. > > > > > _______________________________________________________________________ > This mailing list is neither sponsored nor endorsed by Invensys Process > Systems (formerly The Foxboro Company). Use the info you obtain here at your > own risks. Read http://www.thecassandraproject.org/disclaimer.html > > foxboro mailing list: //www.freelists.org/list/foxboro > to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join > to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave > > > ______________________________________________________________________ > This email has been scanned by the Symantec Email Security.cloud service. > ______________________________________________________________________ > > *** Confidentiality Notice: This e-mail, including any associated or attached > files, is intended solely for the individual or entity to which it is > addressed. This e-mail is confidential and may well also be legally > privileged. If you have received it in error, you are on notice of its > status. Please notify the sender immediately by reply e-mail and then delete > this message from your system. Please do not copy it or use it for any > purposes, or disclose its contents to any other person. This email comes from > a division of the Invensys Group, owned by Invensys Limited, which is a > company registered in England and Wales with its registered office at 3rd > Floor, 40 Grosvenor Place, London, SW1X 7AW (Registered number 166023). For a > list of European legal entities within the Invensys Group, please select the > Legal Entities link at invensys.com. Invensys Limited is owned by the > Schneider-Electric Group. > > You may contact Invensys Limited on +44 (0)20 3155 1200 or e-mail > reception@xxxxxxxxxxxx. This e-mail and any attachments thereto may be > subject to the terms of any agreements between Invensys (and/or its > subsidiaries and affiliates) and the recipient (and/or its subsidiaries and > affiliates). > > > _______________________________________________________________________ > This mailing list is neither sponsored nor endorsed by Invensys Process > Systems (formerly The Foxboro Company). Use the info you obtain here at > your own risks. Read http://www.thecassandraproject.org/disclaimer.html > > foxboro mailing list: //www.freelists.org/list/foxboro > to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join > to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave > > _______________________________________________________________________ This mailing list is neither sponsored nor endorsed by Invensys Process Systems (formerly The Foxboro Company). Use the info you obtain here at your own risks. Read http://www.thecassandraproject.org/disclaimer.html foxboro mailing list: //www.freelists.org/list/foxboro to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave