Hi everyone I need some help with the following question/issue. System: Windows 7-64bit SP1 ColorMunki Photo All X-rite software has been uninstalled Laptop ith nVidia 9800M GTX videocard Using DispcalGUI as the front-end Issue When I try and create a profile, the process fails somewhere midway. The error in the DispcalGUI log reads "Operation aborted..." and the Windows Event viewer showed that DISPREAD.EXE caused an error in MSVCRT.DLL.====================================== Faulting application name: dispread.exe, version: 0.0.0.0, time stamp: 0x4e5e460b Faulting module name: msvcrt.dll, version: 7.0.7600.16385, time stamp: 0x4a5bda6f Exception code: 0xc0000005 Fault offset: 0x0001a6ae Faulting process id: 0x82c Faulting application start time: 0x01cc75f761c3cc58 Faulting application path: C:\photography\Argyll_V1.3.4\bin\dispread.exe Faulting module path: C:\Windows\syswow64\msvcrt.dll Report Id: a0bd97df-e1ea-11e0-bc9a-0090f5840ee9 ====================================== When I run DISPREAD.EXE from the commandline, the same error occurs. The Command line window, shows the below. ====================================== MonitorEnumProc() called with hMonitor = 0x10001 MonitorEnumProc() set initial monitor info: 0,0 1920,1200 name '\\.\DISPLAY1' get_displays about to get monitor information for 0 Mon 0, name '\\.\DISPLAY1\Monitor0' Mon 0, string 'Generic PnP Monitor' Mon 0, flags 0x3 Mon 0, id 'MONITOR\AUO1088\{4d36e96e-e325-11ce-bfc1-08002be10318}\0002' Mon 0, key '\Registry\Machine\System\CurrentControlSet\Control\Class\{4d36e96e-e325-11ce-bfc1-08002be10318}\0002' EnumDisplayDevices failed on '\\.\DISPLAY1' Mon = 1 get_displays added description 'DISPLAY1, at 0, 0, width 1920, height 1200 (Primary Display)' to display 0 Number of patches = 51 Setting up the instrument usb_get_paths about to look through devices: usb_check_and_add() called with VID 0x1d6b, PID 0x1 Get config desc. 0 failed usb_check_and_add() called with VID 0x1d6b, PID 0x1 Get config desc. 0 failed usb_check_and_add() called with VID 0x1d6b, PID 0x1 Get config desc. 0 failed usb_check_and_add() called with VID 0x971, PID 0x2007 usb_check_and_add() found known instrument usb_check_and_add() called with VID 0x1d6b, PID 0x1 Get config desc. 0 failed usb_check_and_add() called with VID 0x1d6b, PID 0x1 Get config desc. 0 failed usb_check_and_add() called with VID 0x1d6b, PID 0x1 Get config desc. 0 failed usb_check_and_add() called with VID 0x147e, PID 0x2016 usb_check_and_add() called with VID 0x1d6b, PID 0x2 Get config desc. 0 failed usb_check_and_add() called with VID 0x1d6b, PID 0x2 Get config desc. 0 failed munki: About to init coms munki: About to init USB icoms: About to set usb port characteristics icoms: About to open the USB port, tries 0 icoms: USB port needs opening icoms: About to open USB port 'usb:/bus2/dev1/ (X-Rite ColorMunki)' icoms: USB port is now open icoms: Clearing any USB errors icoms: usb port characteristics set ok munki: init coms has suceeded munki: About to init instrument munki: GetFirmParms GetFirmParms returns fwrev 1.32, tickdur 32, minint 224, eeblks 2, eeblksz 8192 ICOM err0x0 munki: GetChipID GetChipID returns 01-f302e8120000c5 ICOM err 0x0 munki: GetVersionString GetVersionString returns 'colormunki FW V1.32 Build Nr. 1303' ICOM err 0x0 munki: Read EEProm address 0x4 size 0x4 Read 0x4 bytes, ICOM err 0x0 munki: Read EEProm address 0x0 size 0x1fe9 Read 0x1fe9 bytes, ICOM err 0x0 cal chsum = 0x1e56bc13, should be 0x1e56bc13 - OK Normal non-lin = 0.0000000000 1.0105705261 -0.0000016961 0.0000000001 High Gain non-lin = 0.0000000000 0.2053509504 -0.0000009472 0.0000000000 munki: Read 8 bytes from switch hit port ====================================== I then get a pop-up stating that DISPREAD.EXE has stopped working and I find again the above error in the Windows Application log. Any idea what needs to be done to correct this? Thank you for your help.