On Tuesday 14 December 2004 09:28, Richard Drummond wrote: Hi Richard. > If you know how to use gdb then a report of where the IBrowse fault occurs > would be helpful (with the cache not hosted on a virtual filesystem). Can you help me with gdb? I installed gdb and i ran it, but UAE doesn't boot to the Workbench, but seems to hang somewhwere during boottime. Of course without gdb UAE boots fine. The UAE output when started with gdb is: [kadi@amiga kadi]$ gdb '/home/kadi/Documents/Download/e-uae-0.8.27-RC3-x86-glibc 23/uae' GNU gdb 6.2-2mdk (Mandrakelinux) Copyright 2004 Free Software Foundation, Inc. GDB is free software, covered by the GNU General Public License, and you are welcome to change it and/or distribute copies of it under certain conditions. Type "show copying" to see the conditions. There is absolutely no warranty for GDB. Type "show warranty" for details. This GDB was configured as "i586-mandrake-linux-gnu"...Using host libthread_db l ibrary "/lib/tls/libthread_db.so.1". (gdb) run Starting program: /home/kadi/Documents/Download/e-uae-0.8.27-RC3-x86-glibc23/uae [Thread debugging using libthread_db enabled] [New Thread 1083367648 (LWP 24611)] [New Thread 1091763120 (LWP 24614)] [New Thread 1100155824 (LWP 24615)] E-UAE 0.8.27-RC3 Found 0 joystick(s) Found x11pc raw keyboard mapping Using cooked keymap Opening cfgfile '/home/kadi/.uaerc'...okay. unknown config entry: 'gfx_filter=no' unknown config entry: 'gfx_filter_vert_zoom=0' unknown config entry: 'gfx_filter_horiz_zoom=0' unknown config entry: 'gfx_filter_vert_offset=0' unknown config entry: 'gfx_filter_horiz_offset=0' unknown config entry: 'gfx_filter_scanlines=0' unknown config entry: 'gfx_filter_scanlinelevel=0' unknown config entry: 'gfx_filter_scanlineratio=17' Testing the RDTSC instruction ... done. Calibrating delay loop.. ok - 2010,33 BogoMIPS Testing system sleep function...... Average duration of a 1ms sleep: 2 ms [New Thread 1109048240 (LWP 24621)] [Thread 1109048240 (zombie) exited] Found x11pc raw keyboard mapping Using raw keymap NATMEM: shmget() failed with size 0x08000000. Disabling direct memory access. Follow sprite mode set No disk in drive 0. Resetting frame rate hack Building CPU table for configuration: 68040 1866 CPU functions Building CPU function table, 46416 opcodes (4 0 0). JIT: Max CPUID level=1 Processor is AuthenticAMD JIT: have_cmov=1, have_rat_stall=1 JIT: Setting signal handler JIT: Building Compiler function table JIT: Supposedly 42381 compileable opcodes! JIT: Reverting to "indirect" access, because canbang is zero! Resetting frame rate hack [New Thread 1109048240 (LWP 24627)] [New Thread 1309555632 (LWP 24628)] [New Thread 1317948336 (LWP 24629)] [New Thread 1326341040 (LWP 24630)] scsibus0: 0,0,0 0 'PHILIPS ' 'CDRW1610A ' 'P1.5' CD-ROM 0,1,0 1 * 0,2,0 2 * 0,3,0 3 * 0,4,0 4 * 0,5,0 5 * 0,6,0 6 * 0,7,0 7 * SCSIDEV: 1 devices found support_scsi = 1 support_ioctl = 0 SCSIDEV: Device 'ATAPI' (0,0,0) = uaescsi.device:0 reset at 0 Don't care mouse mode set PAL mode, 50Hz (h=227 v=312) Byte put to custom register DA8000 PC=00F8010A Byte put to custom register DA8000 PC=00F80152 SERIAL: period=372, baud=9600, hsyncs=16 PC=f8018a Fastmem (32bit): mapped @$10000000: 128 MB Zorro III fast memory Card 1 (ZorroIII) done. UAEGFX-card: mapped @$18000000 Card 2 (ZorroIII) done. Filesystem: mapped memory @$e90000. Card 3 (ZorroII) done. Byte put to custom register DFF110 PC=00F8BD96 Byte put to custom register DFF111 PC=00F8BD96 Byte put to custom register DFF112 PC=00F8BD96 Byte put to custom register DFF113 PC=00F8BD96 Byte put to custom register DFF114 PC=00F8BD96 Byte put to custom register DFF115 PC=00F8BD96 Byte put to custom register DFF116 PC=00F8BD96 Byte put to custom register DFF117 PC=00F8BD96 warning: Program does not wait for blitter 0xf8c036 vpos=295 tc=-1 PAL mode, 52Hz (h=227 v=295) PAL mode, 50Hz (h=227 v=312) FS: mounted virtual unit st0 FS: mounted virtual unit st1 FS: mounted virtual unit st2 FS: mounted virtual unit cdr FS: mounted HDF unit DH4 RDB: fakefilesys, trying to load '/home/kadi/LinuxUAE/KadisA1200/FastFileSystem' , dostype 0x444F5300 RDB: filesys not found [New Thread 1334733744 (LWP 24650)] Program received signal SIGSEGV, Segmentation fault. [Switching to Thread 1326341040 (LWP 24630)] 0x08363821 in handle_packet () thanks, kadi