If the TV plays 3 or 4 days, then the problem could be the HOT is getting hot.Did you replace it with the original part # or a substitute?, is the HOT B+ clean?, also check if the low side of the primary drive tx has a dry filter cap. E-mail message Sender: techassist-bounce@xxxxxxxxxxxxx From: DAMON101@xxxxxxxxxxxxxx (Damon) Date: Sat, Nov 24, 2001, 3:39pm To: techassist@xxxxxxxxxxxxx Subject: [TechAssist] Re: projo Reply=A0to: techassist@xxxxxxxxxxxxx Is Q802 the Horiz Sweep output on this model? I'm looking at a PTV 770 schematic....if so test out the hv caps and damper diodes on this. I had a repeat failure on a ptv 375 and I believe this is what I found. Damon Brunger damon101@xxxxxxxxxxxxxx Telrad Electronic Services Ft Wayne, IN 46815 ----- Original Message ----- From: "rcjv" <rcjv@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Saturday, November 24, 2001 1:49 PM Subject: [TechAssist] Re: projo clancy no i dont have wintips the ptv number is ptv835the bd is in the cust house. thnks Raul ----- Original Message ----- From: "Clancy Harms" <dickstv1@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Saturday, November 24, 2001 9:21 AM Subject: [TechAssist] Re: projo Raul Give me the "PTV" number and the board number (APW / APD ???) And I'll see what I can come up with. Do you have the WINStips, or ESD technical tips programs? ive seen the leakage problem and the cracked crt when it leaks onto the bd but this one is different. i put the q802 and the blue is fine i let it play for an hour and its fine. the we deliver it back to the cust and it wks fine for 3 or 4 days. i dont see any leakage or arching . do you have a phillips tech website that i can go to to check for this tia Raul ----- Original Message ----- From: "Clancy Harms" <dickstv1@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Saturday, November 24, 2001 8:43 AM Subject: [TechAssist] Re: projo That's right! I forgot about the leakage "inside" of the CRT. And to think...I just had one last month...DUH! It was a shot in the dark. But the blue CRT was the only one that we could see any type of leakage. We just used a clip to clip lead from the dag to the bare pins of the tube. Sent it PATX in Texas for remanufacturing. And it cost me a WHOPPING.... $88.50 PATX is fantastic! If you need info on them, let me know. Clancy Harms =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 NESDA's Region 7 Director Dick's Radio & TV, Inc. 2319 West Clay St. =A0 =A0 =A0 =A0 =A0 =A0 =A0 If it's broken...a real man can St. Charles, MO. 63301 =A0 =A0 =A0 =A0 =A0 can break it even better ! (636)-724-5055 (636)-724-5531 fax email: =A0 dickstv1@xxxxxxxxxxxxx mailto:dickstv1@xxxxxxxxxxxxx ----- Original Message ----- From: "Don Hartigan" <hartstv@xxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Saturday, November 24, 2001 4:42 AM Subject: [TechAssist] Re: projo Shine a light down the ''Blue crt''.It probably has a hair line crack.Most times it's the Blue but of course check the others as well.Another quick ''field check''is to remove the socket from each crt & hold it close to the pins of the suspect tube,if it draws an ''ARC'',your tube is bad,drawing excessive current,hence blowing your HOT.....hth..regards...Don of HARTS-TVCR ----- Original Message ----- From: "RCJV" <rcjv@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Saturday, November 24, 2001 2:23 AM Subject: [TechAssist] projo hi guys =A0 =A0 =A0 i have a 9p6034c103 ptv philips chassis projo takes out q802 i have replaced the whole powerdef pcb and it takes q802 again. what can i look for is there a fix for this after replacing q802 it wks fine for 3 or 4 days and goes out again tia Raul =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=3Dunsubscribe =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=3Dunsubscribe =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=3Dunsubscribe =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=3Dunsubscribe =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=3Dunsubscribe =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D Good luck, pete ================================= Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips ================================= To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe