Thanks Charles, I'll try it tomorrow. Shaun ----- Original Message ----- From: "repair1" <repair1@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Monday, January 07, 2002 5:50 PM Subject: [TechAssist] Re: Zenith RZ56Z83D7 (no video or OSD) > > > > try r5102 120k on green crt board > charles betzler > Best Electronics > repair1@xxxxxxxxxxxxx > > ----- Original Message ----- > From: "Shaun" <ssroark@xxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Monday, January 07, 2002 6:24 PM > Subject: [TechAssist] Re: Zenith RZ56Z83D7 (no video or OSD) > > > > > > Great thanks that fixed the pix problem but now I have a problem with the > > green. When I bring up the cross hatch the the line from top to bottom is > > purple not white but the line from side to side is white I remember this > > being a bad resistor on the crt soclet board do you know which one? > > > > Shaun > > ----- Original Message ----- > > From: Jerry <geiting@xxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Monday, January 07, 2002 4:35 PM > > Subject: [TechAssist] Re: Zenith RZ56Z83D7 (no video or OSD) > > > > > > > > > > Shaun, > > > The resistors Charles mentioned are in series right off the > collector > > of > > > the horizontal output transistor. They are hard to spot because there > is > > a > > > power resistor mounted above the 1st one off the horz output and there > is > > a > > > lot of clutter in that area. I've found that the 110k is the one that > > > usually opens. > > > > > > Jerry > > > Christians Electronic Service > > > > > > ----- Original Message ----- > > > From: "Shaun" <ssroark@xxxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Monday, January 07, 2002 6:03 PM > > > Subject: [TechAssist] Re: Zenith RZ56Z83D7 (no video or OSD) > > > > > > > > > | > > > | Where are they exactly I still dont see them? > > > | ----- Original Message ----- > > > | From: repair1 <repair1@xxxxxxxxxxxxx> > > > | To: <techassist@xxxxxxxxxxxxx> > > > | Sent: Monday, January 07, 2002 2:43 PM > > > | Subject: [TechAssist] Re: Zenith RZ56Z83D7 (no video or OSD) > > > | > > > | > > > | > > > > | > shaun, replacer3243, and r3244, (by hot heatsink, > > > | > 110k and 82k respectively hth > > > | > charles betzler > > > | > Best Electronics > > > | > repair1@xxxxxxxxxxxxx > > > | > > > > | > > > > | > > > > | > ----- Original Message ----- > > > | > From: "Shaun" <ssroark@xxxxxxxx> > > > | > To: <techassist@xxxxxxxxxxxxx> > > > | > Sent: Monday, January 07, 2002 1:03 PM > > > | > Subject: [TechAssist] Zenith RZ56Z83D7 (no video or OSD) > > > | > > > > | > > > > | > > Hi, I have this Zenith projo that has no video or on screen > display. > > I > > > | can > > > | > turn up the G2 and there is bright screen with retrace lines and the > > > | picture > > > | > looks like the convergance is not working (bowed on top and bottom) > > any > > > | > ideas? > > > | > > > > > | > > Shaun > > > | > > > > > | > > ------------------------------------------ > > > | > > Help make your TechAssist database better! > > > | > > Submit your fixes here: > http://circuitwork.com/techassist/tip/#tips > > > | > > ------------------------------------------ > > > | > > To UNSUBSCRIBE your email address, click here: > > > | > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > | > > Or send a BLANK email with unsubscribe in the > > > | > > SUBJECT field to the address above. > > > | > > > > > | > > > > | > ------------------------------------------ > > > | > Help make your TechAssist database better! > > > | > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > | > ------------------------------------------ > > > | > To UNSUBSCRIBE your email address, click here: > > > | > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > | > Or send a BLANK email with unsubscribe in the > > > | > SUBJECT field to the address above. > > > | > > > > | > > > | ------------------------------------------ > > > | Help make your TechAssist database better! > > > | Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > | ------------------------------------------ > > > | To UNSUBSCRIBE your email address, click here: > > > | mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > | Or send a BLANK email with unsubscribe in the > > > | SUBJECT field to the address above. > > > | > > > > > > > > > ------------------------------------------ > > > Help make your TechAssist database better! > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > ------------------------------------------ > > > To UNSUBSCRIBE your email address, click here: > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > Or send a BLANK email with unsubscribe in the > > > SUBJECT field to the address above. > > > > > > > ------------------------------------------ > > Help make your TechAssist database better! > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > ------------------------------------------ > > To UNSUBSCRIBE your email address, click here: > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > Or send a BLANK email with unsubscribe in the > > SUBJECT field to the address above. > > > > ------------------------------------------ > Help make your TechAssist database better! > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > ------------------------------------------ > To UNSUBSCRIBE your email address, click here: > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > Or send a BLANK email with unsubscribe in the > SUBJECT field to the address above. > ------------------------------------------ Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips ------------------------------------------ To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe Or send a BLANK email with unsubscribe in the SUBJECT field to the address above.