[TechAssist] Re: Zenith B/S PVR5263RK

  • From: "TV Man" <tvman@xxxxxxxxxxxxxxx>
  • To: <techassist@xxxxxxxxxxxxx>
  • Date: Sun, 22 Feb 2004 11:15:29 -0800

No I don't, Dave
TV Man
Inverness, Fl.
----- Original Message ----- 
From: "Ron Miller d.b.a. Country TV" <rlmbkm@xxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Sunday, February 22, 2004 7:02 AM
Subject: [TechAssist] Re: Zenith B/S PVR5263RK


> Do you have a O'scope like an Sencore SC-61 or eqv.?
> Country TV
> Ron Miller
> Inez, TX. 77968
>
> ----- Original Message ----- 
> From: "TV Man" <tvman@xxxxxxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Sunday, February 22, 2004 11:46 AM
> Subject: [TechAssist] Re: Zenith B/S PVR5263RK
>
>
> > Check R3243 is good resoldered stand up board on sweep module still no
> > filaments with anode out of splitter I have HV. Can't check for HV on
CRTs
> > because there seal. If splitter is bad do you lose filaments? Thanks,
Dave
> > TV Man
> > Inverness, Fl.
> > ----- Original Message ----- 
> > From: "Ron Miller d.b.a. Country TV" <rlmbkm@xxxxxxxxxx>
> > To: <techassist@xxxxxxxxxxxxx>
> > Sent: Friday, February 20, 2004 4:12 PM
> > Subject: [TechAssist] Re: Zenith B/S PVR5263RK
> >
> >
> > > He says the set has HV no filament voltage the tubes should have
glowing
> > > filaments with the anode lead removed from splitter and put into a
glass
> > > container.
> > >  If NO filaments at this point IT'S not the splitter.Repair the
Filament
> > > circuit.
> > > Country TV
> > > Ron Miller
> > > Inez, TX. 77968
> > >
> > > ----- Original Message ----- 
> > > From: "armando guerra" <birdie@xxxxxxxxxxxxx>
> > > To: <techassist@xxxxxxxxxxxxx>
> > > Sent: Friday, February 20, 2004 5:35 PM
> > > Subject: [TechAssist] Re: Zenith B/S PVR5263RK
> > >
> > >
> > > > If you remove the lead coming off the flyback into the H.V. divider
> and
> > > you have high voltage there, then the divider\splitter is bad.Very
> common
> > > failure.
> > > > Mando
> > > > Birdie's TV & Electronics
> > > > Casa  GRande, AZ
> > > >
> > > > TV Man wrote:
> > > >
> > > > > Unit has sound no picture. The filaments don't light up. I have HV
> > > coming out of the flyback. How do you check the HV on each tube? They
> seem
> > > to be sealed. I'm guessing the focus block is bad, but before I order
> one
> > I
> > > wanted to get some input. Thanks, Dave
> > > > > TV Man
> > > > > Inverness, Fl.
> > > > >
> > > >
> > >
> >
>
> --------------------------------------------------------------------------
> > > ---
> > > > > Lost Password:
> > > > > http://www.tech-assist.org  and select "Login Problems?".
> > > > > Email Archives:
> > > > > //www.freelists.org/archives/techassist/
> > > >
> > > >
> > >
> >
>
> --------------------------------------------------------------------------
> > > ---
> > > > Lost Password:
> > > > http://www.tech-assist.org  and select "Login Problems?".
> > > > Email Archives:
> > > > //www.freelists.org/archives/techassist/
> > > >
> > > >
> > >
> > >
> > >
> >
>
> --------------------------------------------------------------------------
> > ---
> > > Lost Password:
> > > http://www.tech-assist.org  and select "Login Problems?".
> > > Email Archives:
> > > //www.freelists.org/archives/techassist/
> >
> >
>
> --------------------------------------------------------------------------
> ---
> > Lost Password:
> > http://www.tech-assist.org  and select "Login Problems?".
> > Email Archives:
> > //www.freelists.org/archives/techassist/
> >
> >
>
>
>
> --------------------------------------------------------------------------
---
> Lost Password:
> http://www.tech-assist.org  and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/


-----------------------------------------------------------------------------
Lost Password:
http://www.tech-assist.org  and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/

Other related posts: