Hi Richard, I don't have sams, I have Zenith service manual. If R3211 is burning up either L3201 or D3209 is open. R3211 is in parallel with them. They are in the horz. yoke return path. I could fax you the power supply & deflection schematic if you need it. Bill At 06:20 PM 1/15/02 -0800, you wrote: >Bill, I was wrong on sams # it is 4014, >I replaced R3211 with a substitution box had no horiz.sweep.(Vert line down >middle.) run sub box all the way down to 15 ohms got full picture?I put a >10k resistor in still had no sweep.Then I put a 15 ohm resistor in,and had >sweep.But it burned up.I put a 5.7 ohm 10 watt in, It works good but getting >hot.Maybe a cap pulling to much current?any idea which one. >thanks,Richard > >----- Original Message ----- >From: "Bill Boyd" <billstvs@xxxxxxxxxx> >To: <techassist@xxxxxxxxxxxxx> >Sent: Tuesday, January 15, 2002 3:32 PM >Subject: [TechAssist] Re: ZENITH Z19A11S chassis GA Z line > > > > > > R3211, 10K 1/2W, connects from C3216, 2.2uf 160V, to > > L3201 and 3Y3-2 > > > > D3209, 103-284A, also connects from C3216 to the other end of L3201 > > > > Have zenith manual if you need further help. > > > > HTH > > Bill > > Bill's TV Service > > > > > > At 10:35 PM 1/14/02 -0800, you wrote: > > > > > > > >I don't have the SAMS 4041 for this tv. > > >Zenith z19a11s chassis ga z line ? Came in with hole > > >burned in pc board and burned component. the component > > >is a diode or risistor? I can not tell.one end comes > > >from the cap.c3216 2.2uf/160v.and goes to L3201 and > > >3Y3.Has 99v on 3y3 end -5v? on other. > > > Had vert.line down the middle,(no horiz.)replaced > > >cap. and guessed 116 diode?, worked good.then > > >had line again?(no horiz.)I don't know if yoke or fly, > > >is bad or i am replacing wrong diode.any help > > >appreciated.thanks, > > >Richard > > > > > >===== > > >Richard Golden > > >Golden Video Repair Center > > >1214 e. 6th street > > >ontario ca. 91764 > > >(909)988-3356 > > > > > >reldong@xxxxxxxxx > > > > ------------------------------------------ > > Make your TechAssist database better! > > Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > > ------------------------------------------ > > To UNSUBSCRIBE your email address, click here: > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > Or send a BLANK email with unsubscribe in the > > SUBJECT field to the address above. > >---------------------------------------------------- >Sign Up for NetZero Platinum Today >Only $9.95 per month! >http://my.netzero.net/s/signup?r=platinum&refcd=PT97 >------------------------------------------ >Make your TechAssist database better! >Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ >------------------------------------------ >To UNSUBSCRIBE your email address, click here: >mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe >Or send a BLANK email with unsubscribe in the >SUBJECT field to the address above. ------------------------------------------ Make your TechAssist database better! Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ ------------------------------------------ To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe Or send a BLANK email with unsubscribe in the SUBJECT field to the address above.