Go into the IF module (if there is one) and check the caps. had a 61F90 that had horizontal tearing and it turned out to be the IF module had lots of bad caps. Al Marquardt ampm@xxxxxxx Al Marquardt Electronic Repair 206 W Main Girardville Pa. 17935 ----- Original Message ----- From: "Phil Bader" <tjanphyl@xxxxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Friday, June 24, 2005 4:02 PM Subject: [TechAssist] Re: Toshiba Model:UPDATE TP55G60, Chassis TAC9753, Looks like horizontal sync problem. > Only entries from the techrepairCD: > Toshiba~TP55G60~Unstable picture*bending*weaving and pincushion > distortion~~~~Initialize memory data~With set on press MUTE once (on > remote)*Press and hold MUTE again then press MENU on TV~An *S* will > appear on screen. Press MENU on TV to enter adjustment menu.~To > initialize*While in adjustment menu press and hold RECALL button(on > remote) then press CHANNEL button on TV.~Press POWER button to exit~~ > > Toshiba~TP55G60~The picture would roll vertically~~~~Q501~Replace > Q501~~~~~ > > HTH > Phil > > Philip Bader > Jan Phyl TV Inc. (estab. 1976) > 3420 Recker Hwy. Winter Haven, Fl. 33880 > Fax (863) 299-8821 > email: tjanphyl@xxxxxxxxxxxxxxx > > > > GERALD GANN wrote: > >> He doesn’t have the right schematic just one close. He said the >> signal goes through IC Q764 (TC74HC4050AP) so he changed it still the >> same. Any one have the schematic they could upload to members site or >> tech tips? Thanks >> >>Jerry >> >> >>GERALD GANN <alpha21century1234@xxxxxxxxxxxxx> wrote: >> Toshiba Model: TP55G60, Chassis TAC9753, Looks like horizontal sync >> problem. >> >>Doing this for another shop and a friend of mine. He has helped me in the >>past. >> >>Found one tip in T/A >>Problem: Fish-Eye Picture, >>Cure: Vertical IC 301, LA7833S >> >>I have never looked though a fishs eye so not sure what that means. >>Changed LA7833S No help. I have seen the picture. It dose also look like a >>convergence problem to me but. >> >> He has changed convergence IC they have + & - 18v but looks like the >> convergence circuit is not working. Convergence IC’s is not warm at all >> to the touch. >> >> He changed Switching IC. Also change the DCU module no help. You can >> >> remove the DCU and picture still looks the same. This is the info he gave >> me. Can >> >>some one help on this one. Thanks >> >>Jerry >> >>Alpha 21 Electronics >> >>Granite City, IL 62040 >> >>618-452-8620 >> >>alpha21century1234@xxxxxxxxxxxxx >> >> >> >> >>----------------------------------------------------------------------------- >>This Email List is Public. Remove: http://www.tech-assist.org/remove.htm >>Set Vacation >>mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation >>Lost Password: http://www.tech-assist.org and select "Login Problems?". >>Email Archives: //www.freelists.org/archives/techassist/ >> >> >> >> > ----------------------------------------------------------------------------- > This Email List is Public. Remove: http://www.tech-assist.org/remove.htm > Set Vacation > mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation > Lost Password: http://www.tech-assist.org and select "Login Problems?". > Email Archives: //www.freelists.org/archives/techassist/ > > ----------------------------------------------------------------------------- This Email List is Public. Remove: http://www.tech-assist.org/remove.htm Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/