[TechAssist] Re: TS2744 Chassis # 27B800
- From: "al m" <ampm@xxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Sat, 4 May 2002 12:24:07 -0400
jim i don't see any of this on the screen. when i get in the service menue i
have a sa iin the left hand corner. is that page one. i have a fax on the
lexmark printer i just got but don't know how to receive. try 570-276-1630
that's my phone number
al marquardt
ampm@xxxxxxx
----- Original Message -----
From: "Jim Myers" <jr.myers@xxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Saturday, May 04, 2002 12:10 PM
Subject: [TechAssist] Re: TS2744 Chassis # 27B800
>
> Al, I printed about 12 pages from the alignment section of the service
> manual and will fax to you if you email your fax number to me.
> This may be of some help though, the instruction says to save and exit the
> service menu by "Exit the service mode by repeatedly selecting the menu or
> by pressing the 9 button on the remote transmitter to enter service page
I".
> Then "Press the volume up button while in service page I to power the unit
> off". Then, "Momentarily remove AC power from the chassis to complete the
> exit and save process. ROM defaults are now loaded into the EEPROM"
> Note that service page I is the letter EYE, NOT the number 1.
> Philips technical assistance number for non-authorized servicers is
> 900-896-8324.
> Jim Myers
> Telrad Electronic Services Co.
> Fort Wayne, IN 46815
> jr.myers@xxxxxxxxxxx
> 260-432-4486 Fax and Voice
> Fax is always on
> ----- Original Message -----
> From: "al m" <ampm@xxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Saturday, May 04, 2002 3:03 AM
> Subject: [TechAssist] TS2744 Chassis # 27B800
>
>
>
> can someone help me with this service adjustment. I go into service mode
and
> the first page comes up SA in top left corner RT:00 00 under it and under
> that i get
> bank :00
> register:00
> value: FF
> then when i push #2 on remote i get SB in top left corner and
> IF-PLL:42
> push #3 SC in corner
> AGC:02
> and so on.Can anyone explain how to adjust these parameters and how to
save
> them i don't understand what some of them are for, like Bank and Register
> and Value. these are default values as i reset the values as jim meyers
> explained.thanks Jim.problem is my vertical is compressed. when i go to
> height and vertical slope i can get picture to stretch to normal but i
can't
> save the settings this is what i need to know how to save the settings.
> original problem was no vertical. replaced supply resister, diode, and IC.
> then no raster no sound. after resetting eeprom picture is compressed,and
> have sound.No manual and i don't see many mags around here so i really
don't
> want to spend $50 for a disc.thanks for listening.
> al marquardt
> ampm@xxxxxxx
>
>
>
>
>
> ------------------------------------------
> To REMOVE your email address, click here:
> http://www.tech-assist.org/unsubb.html
> ------------------------------------------
> ***NEW*** Tips Added Instantly!!!***
> Submit Repair Tips here:
> http://www.tech-assist.org/secure/tip/
>
> ------------------------------------------
> To REMOVE your email address, click here:
> http://www.tech-assist.org/unsubb.html
> ------------------------------------------
> ***NEW*** Tips Added Instantly!!!***
> Submit Repair Tips here:
> http://www.tech-assist.org/secure/tip/
>
------------------------------------------
To REMOVE your email address, click here:
http://www.tech-assist.org/unsubb.html
------------------------------------------
***NEW*** Tips Added Instantly!!!***
Submit Repair Tips here:
http://www.tech-assist.org/secure/tip/
Other related posts:
