/// Does your relay have an enclosed diode? Even if no current flows you should read 12 volts on both sides of the relay if the coil is not open. >From: "Bruce Youmans" <youmans@xxxxxxxx> >Reply-To: techassist@xxxxxxxxxxxxx >To: <techassist@xxxxxxxxxxxxx> >Subject: [TechAssist] Re: Sony SL-2500 Beta Dead, Part ID >Date: Thu, 10 Jan 2002 05:48:06 -0700 > > >Don, > >I have traced the 12 volt input of IC3 back to the relay. The relay is not >being activated. Has 12 volts on relay coil. I have checked the transistor >that grounds the other side of the relay coil and it is fine. Relay is >fine. >I have tried manually shorting the relay contacts. 12 volts come up, but >still no clock and no function operation. > >Bruce >----- Original Message ----- >From: Don-WRF Electronics <wrf_88@xxxxxxxxx> >To: <techassist@xxxxxxxxxxxxx> >Sent: Thursday, January 10, 2002 3:22 AM >Subject: [TechAssist] Re: Sony SL-2500 Beta Dead, Part ID > > > > > > Bruce the 12v comes from RL1 and is switched. > > Don-- ps I never had any faults with that power > > suppy > > either. > > > > --- Bruce Youmans <youmans@xxxxxxxx> wrote: > > > > > > Jerry, > > > > > > There is no 12 volts on the input. Because I'm > > > working without a schematic > > > I'm not sure there is 12 volts on the input when the > > > VCR is in the standby > > > (off) mode. Yes, it is possible an electrolytic > > > capacitor or two may be bad > > > because of the age.. I have checked most of them and > > > so far the ESR is good. > > > I was also thinking that there may be a ICP or low > > > value resistor that has > > > opened. This is because everything is inoperative, > > > even the clock in the off > > > mode. The customer said the VCR was plugged in and > > > one day when they went to > > > use it everything was dead. I have checked all three > > > of the fuses and they > > > are OK. There are some voltages on the power supply > > > board in various > > > locations. Not sure if they are correct. Any other > > > thoughts you might have > > > are appreciated. > > > > > > Bruce > > > ----- Original Message ----- > > > From: J Silverman <greentron@xxxxxxxxxxxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Tuesday, January 08, 2002 10:45 AM > > > Subject: [TechAssist] Re: Sony SL-2500 Beta Dead, > > > Part ID > > > > > > > > > > > > > > If that IC has 12 volts input, it should have 9 > > > volts output. If there is > > > no > > > > 12 volts the problem is elsewhere. I dont recall > > > ever having a power > > > problem > > > > with that model. Considering the age, I would > > > think some of the > > > electrolytic > > > > capacitors may be dried out. > > > > Jerry Silverman > > > > Greentron Inc > > > > 4 Newland Ave > > > > Greenville SC 29609 > > > > 864 232 3889 > > > > Fax 271 2080 > > > > mailto:greentron@xxxxxxx > > > > ----- Original Message ----- > > > > From: "Bruce Youmans" <youmans@xxxxxxxx> > > > > To: <techassist@xxxxxxxxxxxxx> > > > > Sent: Monday, January 07, 2002 12:50 PM > > > > Subject: [TechAssist] Re: Sony SL-2500 Beta Dead, > > > Part ID > > > > > > > > > > > > > > > > > > Thanks Jerry. > > > > > > > > > > I have been trying to repair this VCR without a > > > schematic. The part had > > > no > > > > > information on it. I was hoping that this part > > > would be the reason the > > > VCR > > > > > is dead, has no display, and no function > > > operation at all. > > > > > > > > > > Bruce > > > > > Bruce's TV Service > > > > > Sierra Vista, Arizona > > > > > > > > > > ----- Original Message ----- > > > > > From: J Silverman <greentron@xxxxxxxxxxxxxxxx> > > > > > To: <techassist@xxxxxxxxxxxxx> > > > > > Sent: Monday, January 07, 2002 9:58 AM > > > > > Subject: [TechAssist] Re: Sony SL-2500 Beta > > > Dead, Part ID > > > > > > > > > > > > > > > > > > > > > > That is a 78M08, standard 8 volt, 1/2 amp 3 > > > terminal voltage > > > regulator. > > > > > Sony > > > > > > 8 759 170 08. > > > > > > Jerry Silverman > > > > > > Greentron Inc > > > > > > 4 Newland Ave > > > > > > Greenville SC 29609 > > > > > > 864 232 3889 > > > > > > Fax 271 2080 > > > > > > mailto:greentron@xxxxxxx > > > > > > ----- Original Message ----- > > > > > > From: "Bruce Youmans" <youmans@xxxxxxxx> > > > > > > To: <techassist@xxxxxxxxxxxxx> > > > > > > Sent: Sunday, January 06, 2002 10:57 PM > > > > > > Subject: [TechAssist] Re: Sony SL-2500 Beta > > > Dead, Part ID > > > > > > > > > > > > > > > > > > > > > > > > > > Need to know the part number for IC3 on the > > > power supply board. > > > > > > > This unit is a Sony Sl-2500, but is similar > > > to a Zenith VR-9775. > > > > > > > > > > > > > > Thanks. > > > > > > > > > > > > > > Bruce > > > > > > > Bruce's TV Service > > > > > > > Sierra Vista, Arizona > > > > > > > > > > > > > > ----- Original Message ----- > > > > > > > From: Bruce Youmans <youmans@xxxxxxxx> > > > > > > > To: <techassist@xxxxxxxxxxxxx> > > > > > > > Sent: Friday, January 04, 2002 9:36 AM > > > > > > > Subject: [TechAssist] Re: Sony SL-2500 Beta > > > Dead > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Just learned this Sony Beta is similar to > > > a Zenith VR9775 in case > > > > > anyone > > > > > > > has > > > > > > > > information on either. > > > > > > > > > > > > > > > > Thanks > > > > > > > > > > > > > > > > Bruce > > > > > > > > Bruce's TV Service > > > > > > > > Sierra Vista, Arizona > > > > > > > > > > > > > > > > ----- Original Message ----- > > > > > > > > From: Bruce Youmans <youmans@xxxxxxxx> > > > > > > > > To: <techassist@xxxxxxxxxxxxx> > > > > > > > > Sent: Wednesday, January 02, 2002 10:18 PM > > > > > > > > Subject: [TechAssist] Sony SL-2500 Beta > > > Dead > > > > > > > > > > > > > > > > > > > > > > > > > Manufacturer: Sony > > > > > > > > > Model: SL-2500 Beta VCR > > > > > > > > > Symptom: Dead > > > > > > > > > > > > > > > > > > Received today a Sony Beta VCR for > > > repair. Not sure this is > > > worth > > > > > > > digging > > > > > > > > into unless it may be something simple. > > > Unit is totally dead. No > > > > > display > > > > > > > or > > > > > > > > any action when the power button is > > > pushed. Primary fuse, F1, is > > > > fine. > > > > > > No > > > > > > > > schematic on this one and the unit is > > > pretty compact so I hate to > > > > dig > > > > > > into > > > > > > > > it without some advance help. Any help > > > would be appreciated. > > > > > > > > > > > > > > > > > > Bruce > > > > > > > > > Bruce's TV Service > > > > > > > > > Sierra Vista, Arizona > > > > > > > > > > > > > > > > > > > > > ------------------------------------------ > > > > > > > > > Help make your TechAssist database > > > better! > > > > > > > > > Submit your fixes here: > > > > http://circuitwork.com/techassist/tip/#tips > > > > > > > > > > > > ------------------------------------------ > > > > > > > > > To UNSUBSCRIBE your email address, click > > > here: > > > > > > > > > > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > > > Or send a BLANK email with unsubscribe > > > in the > > > > > > > > > SUBJECT field to the address above. > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > ------------------------------------------ > > > > > > > > Help make your TechAssist database better! > > > > > > > > Submit your fixes here: > > > http://circuitwork.com/techassist/tip/#tips > > > > > > > > ------------------------------------------ > > > > > > > > To UNSUBSCRIBE your email address, click > > > here: > > > > > > > > > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > > Or send a BLANK email with unsubscribe in > > > the > > > > > === message truncated === > > > > > > __________________________________________________ > > Do You Yahoo!? > > Send FREE video emails in Yahoo! Mail! > > http://promo.yahoo.com/videomail/ > > ------------------------------------------ > > Help make your TechAssist database better! > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > ------------------------------------------ > > To UNSUBSCRIBE your email address, click here: > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > Or send a BLANK email with unsubscribe in the > > SUBJECT field to the address above. > > > > > >------------------------------------------ >Help make your TechAssist database better! >Submit your fixes here: http://circuitwork.com/techassist/tip/#tips >------------------------------------------ >To UNSUBSCRIBE your email address, click here: >mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe >Or send a BLANK email with unsubscribe in the >SUBJECT field to the address above. > _________________________________________________________________ Send and receive Hotmail on your mobile device: http://mobile.msn.com ------------------------------------------ Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips ------------------------------------------ To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe Or send a BLANK email with unsubscribe in the SUBJECT field to the address above.