The ringing test is patented by Sencore and is incorporated in a variety of their test equipment. Jerry Silverman Greentron Inc 4 Newland Ave Greenville SC 29609 864 232 3889 Fax 271 2080 mailto:greentron@xxxxxxx ----- Original Message ----- From: "VRM" <vrmsys@xxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Wednesday, January 09, 2002 1:26 PM Subject: [TechAssist] Re: SONY TV VERTICAL NOT FULL > > Hello, > > Please which voltage are you talking about? Is it the supply voltage for the > chip? If it is, then the voltage imprinted on the circuit board for the > Vertical IC is +- 25VDC, and am measuring just about that, i.e.+-24.3V. > > I have a generic application schematic diagram from the CHIP manufacturers, > ST Microelectronics and the parameters stated, conforms to the design from > SONY. > > May I know the voltage in question for me try my hands on once again. How do > I go about with the RINGING TEST, please help by giving me the STEPS. > > Thanks very much for the information. Hope to hear from you soon. > > Viktoria > > ----- Original Message ----- > From: "J Silverman" <greentron@xxxxxxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Tuesday, January 08, 2002 5:57 PM > Subject: [TechAssist] Re: SONY TV VERTICAL NOT FULL > > > > > > The voltage to the vertical IC may be low due to a problem with the FBT or > > one of its loads or the HOT drive. Another possibility is a short in the > > yoke. You could tell with a ringing test. > > Jerry Silverman > > Greentron Inc > > 4 Newland Ave > > Greenville SC 29609 > > 864 232 3889 > > Fax 271 2080 > > mailto:greentron@xxxxxxx > > ----- Original Message ----- > > From: "VRM" <vrmsys@xxxxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Tuesday, January 08, 2002 7:08 AM > > Subject: [TechAssist] Re: SONY TV VERTICAL NOT FULL > > > > > > > > > > Hello; > > > > > > Thanks for the reply. The PICTURE is NEITHER compressed NOR CUTOFF at > the > > > TOP and BOTTOM, but just that it does not FULLY FILL the screen. Also > the > > > VERTICAL Deflection IC warms up too quickly (i.e. Temperature Increases > > > Exponentially) at power up. I appreciate all the help you are providing. > > > > > > Actually, the SET was brought in having a BURNT (SHORTED) HORIZONTAL > > > Transistor, and then after REPAIRS, the problem was detected. I asked > the > > > owner whether he has seen the SET behave that way before, he said > > > occasionally it has been that way (FULL or SEMI FULL Screen), before it > > > finally went down. > > > > > > Hope to hear from you soon. > > > > > > Thanks > > > > > > Viktoria > > > > > > > > > ----- Original Message ----- > > > From: "Dennis Viereck" <wa6ati@xxxxxxxxxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Monday, January 07, 2002 7:27 PM > > > Subject: [TechAssist] Re: SONY TV VERTICAL NOT FULL > > > > > > > > > > > > > > Is the picture compressed at the top and bottom or cut off at top and > > > bottom? > > > > Dennis > > > > > > > > VRM wrote: > > > > > > > > > Hello; > > > > > > > > > > It is JUST the TOP and DOWN. I have good signal RECEPTION. The > IMAGES > > > are > > > > > complete, i.e FULL image displayed, BUT my problem is TOP and DOWN > > > picture > > > > > shortage. > > > > > > > > > > Thanks > > > > > > > > > > ----- Original Message ----- > > > > > From: "al m" <ampm@xxxxxxx> > > > > > To: <techassist@xxxxxxxxxxxxx> > > > > > Sent: Monday, January 07, 2002 5:48 PM > > > > > Subject: [TechAssist] Re: SONY TV VERTICAL NOT FULL > > > > > > > > > > > > > > > > > are you saying the whole picture is small or just the top and > bottom > > > > > > al marquardt > > > > > > ampm@xxxxxxx > > > > > > ----- Original Message ----- > > > > > > From: "VRM" <vrmsys@xxxxxxxxxxxx> > > > > > > To: <Techassist@xxxxxxxxxxxxx> > > > > > > Sent: Monday, January 07, 2002 10:47 AM > > > > > > Subject: [TechAssist] SONY TV VERTICAL NOT FULL > > > > > > > > > > > > > > > > > > > Hello; > > > > > > > > > > > > > > I will be very pleased if someone can help me repair this SONY > TV > > > with a > > > > > > vertical deflection Problem. > > > > > > > > > > > > > > The SET is a SONY 29 inch with MODEL number KV-29MF1, which > powers > > > up > > > > > > well, but having a vertical deflection (Picture) covering/centered > > > around > > > > > > 80% of the screen. The SET has a vertical deflection booster IC > > > TDA9379, > > > > > > which I suspected to be faulty and changed it, in addition to all > > > > > > electrolytic capacitors located in the vertical deflection > section - > > > i.e. > > > > > a > > > > > > valuable suggestion from response from a TECH ASSIST reply. > > > > > > > > > > > > > > The fault is still not repaired, aside that, the Vertical IC > warms > > > up > > > > > > INCREASINGLY at power up. Actaully I don't have a schematic > diagram > > > for > > > > > this > > > > > > SET. > > > > > > > > > > > > > > Would someone be willing to provide suggestions or ideas as to > > what > > > next > > > > > I > > > > > > can touch to help solve this problem. > > > > > > > > > > > > > > WISHING YOU ALL the BEST OF the SEASON - Thanks a lot. > > > > > > > > > > > > > > Viktoria > > > > > > > > > > > > > > ------------------------------------------ > > > > > > > Help make your TechAssist database better! > > > > > > > Submit your fixes here: > > http://circuitwork.com/techassist/tip/#tips > > > > > > > ------------------------------------------ > > > > > > > To UNSUBSCRIBE your email address, click here: > > > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > Or send a BLANK email with unsubscribe in the > > > > > > > SUBJECT field to the address above. > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > ------------------------------------------ > > > > > > Help make your TechAssist database better! > > > > > > Submit your fixes here: > http://circuitwork.com/techassist/tip/#tips > > > > > > ------------------------------------------ > > > > > > To UNSUBSCRIBE your email address, click here: > > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > Or send a BLANK email with unsubscribe in the > > > > > > SUBJECT field to the address above. > > > > > > > > > > > > > > > > ------------------------------------------ > > > > > Help make your TechAssist database better! > > > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > > > ------------------------------------------ > > > > > To UNSUBSCRIBE your email address, click here: > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > Or send a BLANK email with unsubscribe in the > > > > > SUBJECT field to the address above. > > > > > > > > ------------------------------------------ > > > > Help make your TechAssist database better! > > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > > ------------------------------------------ > > > > To UNSUBSCRIBE your email address, click here: > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > Or send a BLANK email with unsubscribe in the > > > > SUBJECT field to the address above. > > > > > > > > > > ------------------------------------------ > > > Help make your TechAssist database better! > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > ------------------------------------------ > > > To UNSUBSCRIBE your email address, click here: > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > Or send a BLANK email with unsubscribe in the > > > SUBJECT field to the address above. > > > > > > > > > > ------------------------------------------ > > Help make your TechAssist database better! > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > ------------------------------------------ > > To UNSUBSCRIBE your email address, click here: > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > Or send a BLANK email with unsubscribe in the > > SUBJECT field to the address above. > > > > ------------------------------------------ > Help make your TechAssist database better! > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > ------------------------------------------ > To UNSUBSCRIBE your email address, click here: > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > Or send a BLANK email with unsubscribe in the > SUBJECT field to the address above. > ------------------------------------------ Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips ------------------------------------------ To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe Or send a BLANK email with unsubscribe in the SUBJECT field to the address above.