[TechAssist] Re: :SANYO AVM 276A shuts down on tv mode videook
- From: "Ken Dinckan" <kdinckan@xxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Tue, 29 Jan 2002 22:18:02 -0800
thanks
I will check it
Ken Dinckan
ALL Tv&Appliance Service
2747 Roosevelt Street # B
Carlsbad CA, 92008
tel: (760)434-1131
fax: (760)434-8856
email to : kdinckan@xxxxxxx
----- Original Message -----
From: "al m" <ampm@xxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Wednesday, January 30, 2002 6:09 AM
Subject: [TechAssist] Re: :SANYO AVM 276A shuts down on tv mode videook
>
> if you have a schematic find where the sync signal goes to the micro and
> check that line. had the same problem was a bad cap on the sync line to
the
> micro.
> al marquardt
> ampm@xxxxxxx
>
>
> ----- Original Message -----
> From: "Edward Gaidies" <teltek@xxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Tuesday, January 29, 2002 5:16 PM
> Subject: [TechAssist] Re: :SANYO AVM 276A shuts down on tv mode videook
>
>
> >
> > You may have to do some allignment of the AFT, sounds like you are weak
on
> > the sync input. This is the same signal that autoprogram seeks. This is
> the
> > one that is not strong enough, and activates your autoshutdown Me
thinks.
> >
> > -Ed-
> >
> > >
> > > ok I will try but don't you think if the signal weak picture should be
> > > snowy. When I change the channels first picture try to settle like
> tuning
> > > and then locks it in. Something to do with the signal. But since
picture
> > > quality good I thought the signal not weak.
> > > thanks
> > >
> > > Ken Dinckan
> > > ALL TV&Appliance Service
> > > 2747 Roosevelt Street # B
> > > Carlsbad CA, 92008
> > > tel: (760)434-1131
> > > fax: (760)434-8856
> > > email to : kdinckan@xxxxxxx
> > > ----- Original Message -----
> > > From: "Gary McCartney" <number63@xxxxxxxxxxxxx>
> > > To: <techassist@xxxxxxxxxxxxx>
> > > Sent: Tuesday, January 29, 2002 2:28 PM
> > > Subject: [TechAssist] Re: :SANYO AVM 276A shuts down on tv mode video
ok
> > >
> > >
> > >>
> > >> try connecting the cable directly to the tuner instead of going
through
> > >> the balun - unless the arrangement has the RF connector built right
on
> > >> the tuner. (make sure tv is plugged into isolation transformer) to
see
> > >> if the signal is weak entering tuner.
> > >>
> > >>
> > >>
> > >> Gary McCartney
> > >>
> > >> McCartney Electronics
> > >> 7134 Fife Rd, RR 7
> > >> Guelph Ontario Canada N1H 6J4
> > >> Fax: (519)821-1530
> > >> email: number63@xxxxxxxxxxxxx
> > >>
> > >>
> > >>
> > >>
> > >> Ken Dinckan wrote:
> > >>>
> > >>> hi Gary
> > >>> this happens when signal is present. replaced the tuner and micro
> still
> > >>> same. it is acting like no signal comin in tuner
> > >>>
> > >>> Ken Dinckan
> > >>> ALL Tv&Appliance Service
> > >>> 2747 Roosevelt Street # B
> > >>> Carlsbad CA, 92008
> > >>> tel: (760)434-1131
> > >>> fax: (760)434-8856
> > >>> email to : kdinckan@xxxxxxx
> > >>> ----- Original Message -----
> > >>> From: "Gary McCartney" <number63@xxxxxxxxxxxxx>
> > >>> To: <techassist@xxxxxxxxxxxxx>
> > >>> Sent: Tuesday, January 29, 2002 12:37 PM
> > >>> Subject: [TechAssist] Re: :SANYO AVM 276A shuts down on tv mode
video
> ok
> > >>>
> > >>>>
> > >>>> Ken, maybe it has auto shut-off if no antenna is connected (no
signal
> > >>>> present for 15 min. such as when station goes off air late at
night,
> > > so
> > >>>> the set shuts off if viewer happens to fall asleep.)
> > >>>>
> > >>>>
> > >>>>
> > >>>> Gary McCartney
> > >>>>
> > >>>> McCartney Electronics
> > >>>> 7134 Fife Rd, RR 7
> > >>>> Guelph Ontario Canada N1H 6J4
> > >>>> Fax: (519)821-1530
> > >>>> email: number63@xxxxxxxxxxxxx
> > >>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>> Ken Dinckan wrote:
> > >>>>>
> > >>>>> Second Post
> > >>>>> Anyone have idea for this tv shuts down in 15 minutes when the tv
> > > mode
> > >>>>> selected. But when video input used won't shut down
> > >>>>>
> > >>>>> Ken Dinckan
> > >>>>> ALL Tv&Appliance Service
> > >>>>> 2747 Roosevelt Street # B
> > >>>>> Carlsbad CA, 92008
> > >>>>> tel: (760)434-1131
> > >>>>> fax: (760)434-8856
> > >>>>> email to : kdinckan@xxxxxxx
> > >>>>> ----- Original Message -----
> > >>>>> From: "Ken Dinckan" <kdinckan@xxxxxxx>
> > >>>>> To: <techassist@xxxxxxxxxxxxx>
> > >>>>> Sent: Tuesday, January 22, 2002 1:52 AM
> > >>>>> Subject: *****SPAM***** [TechAssist] Re: SANYO AVM 276A
> > >>>>>
> > >>>>>>
> > >>>>>> I did run for low AC but no change any other help you can give
> > >>>>>> thanks
> > >>>>>>
> > >>>>>> Ken Dinckan
> > >>>>>> ALL Tv&Appliance Service
> > >>>>>> 2747 Roosevelt Street # B
> > >>>>>> Carlsbad CA, 92008
> > >>>>>> tel: (760)434-1131
> > >>>>>> fax: (760)434-8856
> > >>>>>> email to : kdinckan@xxxxxxx
> > >>>>>> ----- Original Message -----
> > >>>>>> From: "Gonzalo Arrivas" <gna2000@xxxxxxx>
> > >>>>>> To: <techassist@xxxxxxxxxxxxx>
> > >>>>>> Sent: Wednesday, January 09, 2002 1:42 PM
> > >>>>>> Subject: [TechAssist] Re: SANYO AVM 276A
> > >>>>>>
> > >>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>> Ken,
> > >>>>>>>
> > >>>>>>> Try running it at a lower AC voltage (approx. 90VAC)using a
> > > variac
> > >>> on
> > >>>>> the
> > >>>>>> TV
> > >>>>>>> mode and see what happen and let me know.
> > >>>>>>>
> > >>>>>>> G.N.Arrivas, CET Pittsburg, CA
> > >>>>>>> http://www.etechhelponline,com
> > >>>>>>>
> > >>>>>>>> From: "Ken Dinckan" <kdinckan@xxxxxxx>
> > >>>>>>>> Reply-To: techassist@xxxxxxxxxxxxx
> > >>>>>>>> To: <techassist@xxxxxxxxxxxxx>
> > >>>>>>>> Subject: [TechAssist] SANYO AVM 276A
> > >>>>>>>> Date: Wed, 9 Jan 2002 00:33:04 -0800
> > >>>>>>>>
> > >>>>>>>> anyone help for the Sanyo tv shuts down 10-15 minutes when tv
> > > mode
> > >>>>>>>> selected. Won't shut down when video inputs selected. Suspected
> > > IF
> > >>>>>>>> problem??
> > >>>>>>>>
> > >>>>>>>> ------------------------------------------
> > >>>>>>>> Help make your TechAssist database better!
> > >>>>>>>> Submit your fixes here:
> > > http://circuitwork.com/techassist/tip/#tips
> > >>>>>>>> ------------------------------------------
> > >>>>>>>> To UNSUBSCRIBE your email address, click here:
> > >>>>>>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > >>>>>>>> Or send a BLANK email with unsubscribe in the
> > >>>>>>>> SUBJECT field to the address above.
> > >>>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > >>>>>>> G.N.Arrivas, CET, Pittsburg. CA
> > >>>>>>> Tel/Fax: 925-432-2057
> > >>>>>>> Email: gna2000@xxxxxxx
> > >>>>>>>
> > >>>>>>> For Tech Repair Help:
> > >>>>>>> http://www.etechhelponline.com
> > >>>>>>> (Now viewed by technicians in 60-plus countries worldwide.)
> > >>>>>>
> > >>>>>
> > >>>
> >
>
>> -------------------------------------------------------------------------
> -
> > >>>>>>> Tax Help & Services:
> > >>>>>>> http://www.itaxhelponline.com
> > >>>>>>
> > >>>>>
> > >>>
> >
>
>> -------------------------------------------------------------------------
> > >>>>>>> Business Opportunities & Lifestyle!
> > >>>>>>> http://www.arrivasenterprises.com
> > >>>>>>>
> > >>>>>>>
> > >>>>>>>
> > > _________________________________________________________________
> > >>>>>>> MSN Photos is the easiest way to share and print your photos:
> > >>>>>>> http://photos.msn.com/support/worldwide.aspx
> > >>>>>>>
> > >>>>>>> ------------------------------------------
> > >>>>>>> Help make your TechAssist database better!
> > >>>>>>> Submit your fixes here:
> > > http://circuitwork.com/techassist/tip/#tips
> > >>>>>>> ------------------------------------------
> > >>>>>>> To UNSUBSCRIBE your email address, click here:
> > >>>>>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > >>>>>>> Or send a BLANK email with unsubscribe in the
> > >>>>>>> SUBJECT field to the address above.
> > >>>>>>>
> > >>>>>>>
> > >>>>>>
> > >>>>>>
> > >>>>>> ------------------------------------------
> > >>>>>> Make your TechAssist database better!
> > >>>>>> Submit Repair Tips here: http://www.tech-assist.org/secure/tip/
> > >>>>>> ------------------------------------------
> > >>>>>> To UNSUBSCRIBE your email address, click here:
> > >>>>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > >>>>>> Or send a BLANK email with unsubscribe in the
> > >>>>>> SUBJECT field to the address above.
> > >>>>>>
> > >>>>>>
> > >>>>>
> > >>>>> ------------------------------------------
> > >>>>> Make your TechAssist database better!
> > >>>>> Submit Repair Tips here: http://www.tech-assist.org/secure/tip/
> > >>>>> ------------------------------------------
> > >>>>> To UNSUBSCRIBE your email address, click here:
> > >>>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > >>>>> Or send a BLANK email with unsubscribe in the
> > >>>>> SUBJECT field to the address above.
> > >>>>
> > >>>> --
> > >>>> ------------------------------------------
> > >>>> Make your TechAssist database better!
> > >>>> Submit Repair Tips here: http://www.tech-assist.org/secure/tip/
> > >>>> ------------------------------------------
> > >>>> To UNSUBSCRIBE your email address, click here:
> > >>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > >>>> Or send a BLANK email with unsubscribe in the
> > >>>> SUBJECT field to the address above.
> > >>>>
> > >>>>
> > >>>
> > >>> ------------------------------------------
> > >>> Make your TechAssist database better!
> > >>> Submit Repair Tips here: http://www.tech-assist.org/secure/tip/
> > >>> ------------------------------------------
> > >>> To UNSUBSCRIBE your email address, click here:
> > >>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > >>> Or send a BLANK email with unsubscribe in the
> > >>> SUBJECT field to the address above.
> > >>
> > >> --
> > >> ------------------------------------------
> > >> Make your TechAssist database better!
> > >> Submit Repair Tips here: http://www.tech-assist.org/secure/tip/
> > >> ------------------------------------------
> > >> To UNSUBSCRIBE your email address, click here:
> > >> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > >> Or send a BLANK email with unsubscribe in the
> > >> SUBJECT field to the address above.
> > >>
> > >>
> > >
> > >
> > > ------------------------------------------
> > > Make your TechAssist database better!
> > > Submit Repair Tips here: http://www.tech-assist.org/secure/tip/
> > > ------------------------------------------
> > > To UNSUBSCRIBE your email address, click here:
> > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > Or send a BLANK email with unsubscribe in the
> > > SUBJECT field to the address above.
> > >
> >
> > --
> > From: Ed Gaidies
> > teltek@xxxxxxxxxxx
> > Tel-Tek Electronics
> >
> > ------------------------------------------
> > Make your TechAssist database better!
> > Submit Repair Tips here: http://www.tech-assist.org/secure/tip/
> > ------------------------------------------
> > To UNSUBSCRIBE your email address, click here:
> > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > Or send a BLANK email with unsubscribe in the
> > SUBJECT field to the address above.
> >
> >
> >
>
>
> ------------------------------------------
> Make your TechAssist database better!
> Submit Repair Tips here: http://www.tech-assist.org/secure/tip/
> ------------------------------------------
> To UNSUBSCRIBE your email address, click here:
> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> Or send a BLANK email with unsubscribe in the
> SUBJECT field to the address above.
>
>
------------------------------------------
Make your TechAssist database better!
Submit Repair Tips here: http://www.tech-assist.org/secure/tip/
------------------------------------------
To UNSUBSCRIBE your email address, click here:
mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
Or send a BLANK email with unsubscribe in the
SUBJECT field to the address above.
Other related posts:
