if you have a schematic find where the sync signal goes to the micro and check that line. had the same problem was a bad cap on the sync line to the micro. al marquardt ampm@xxxxxxx ----- Original Message ----- From: "Edward Gaidies" <teltek@xxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Tuesday, January 29, 2002 5:16 PM Subject: [TechAssist] Re: :SANYO AVM 276A shuts down on tv mode videook > > You may have to do some allignment of the AFT, sounds like you are weak on > the sync input. This is the same signal that autoprogram seeks. This is the > one that is not strong enough, and activates your autoshutdown Me thinks. > > -Ed- > > > > > ok I will try but don't you think if the signal weak picture should be > > snowy. When I change the channels first picture try to settle like tuning > > and then locks it in. Something to do with the signal. But since picture > > quality good I thought the signal not weak. > > thanks > > > > Ken Dinckan > > ALL TV&Appliance Service > > 2747 Roosevelt Street # B > > Carlsbad CA, 92008 > > tel: (760)434-1131 > > fax: (760)434-8856 > > email to : kdinckan@xxxxxxx > > ----- Original Message ----- > > From: "Gary McCartney" <number63@xxxxxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Tuesday, January 29, 2002 2:28 PM > > Subject: [TechAssist] Re: :SANYO AVM 276A shuts down on tv mode video ok > > > > > >> > >> try connecting the cable directly to the tuner instead of going through > >> the balun - unless the arrangement has the RF connector built right on > >> the tuner. (make sure tv is plugged into isolation transformer) to see > >> if the signal is weak entering tuner. > >> > >> > >> > >> Gary McCartney > >> > >> McCartney Electronics > >> 7134 Fife Rd, RR 7 > >> Guelph Ontario Canada N1H 6J4 > >> Fax: (519)821-1530 > >> email: number63@xxxxxxxxxxxxx > >> > >> > >> > >> > >> Ken Dinckan wrote: > >>> > >>> hi Gary > >>> this happens when signal is present. replaced the tuner and micro still > >>> same. it is acting like no signal comin in tuner > >>> > >>> Ken Dinckan > >>> ALL Tv&Appliance Service > >>> 2747 Roosevelt Street # B > >>> Carlsbad CA, 92008 > >>> tel: (760)434-1131 > >>> fax: (760)434-8856 > >>> email to : kdinckan@xxxxxxx > >>> ----- Original Message ----- > >>> From: "Gary McCartney" <number63@xxxxxxxxxxxxx> > >>> To: <techassist@xxxxxxxxxxxxx> > >>> Sent: Tuesday, January 29, 2002 12:37 PM > >>> Subject: [TechAssist] Re: :SANYO AVM 276A shuts down on tv mode video ok > >>> > >>>> > >>>> Ken, maybe it has auto shut-off if no antenna is connected (no signal > >>>> present for 15 min. such as when station goes off air late at night, > > so > >>>> the set shuts off if viewer happens to fall asleep.) > >>>> > >>>> > >>>> > >>>> Gary McCartney > >>>> > >>>> McCartney Electronics > >>>> 7134 Fife Rd, RR 7 > >>>> Guelph Ontario Canada N1H 6J4 > >>>> Fax: (519)821-1530 > >>>> email: number63@xxxxxxxxxxxxx > >>>> > >>>> > >>>> > >>>> > >>>> > >>>> Ken Dinckan wrote: > >>>>> > >>>>> Second Post > >>>>> Anyone have idea for this tv shuts down in 15 minutes when the tv > > mode > >>>>> selected. But when video input used won't shut down > >>>>> > >>>>> Ken Dinckan > >>>>> ALL Tv&Appliance Service > >>>>> 2747 Roosevelt Street # B > >>>>> Carlsbad CA, 92008 > >>>>> tel: (760)434-1131 > >>>>> fax: (760)434-8856 > >>>>> email to : kdinckan@xxxxxxx > >>>>> ----- Original Message ----- > >>>>> From: "Ken Dinckan" <kdinckan@xxxxxxx> > >>>>> To: <techassist@xxxxxxxxxxxxx> > >>>>> Sent: Tuesday, January 22, 2002 1:52 AM > >>>>> Subject: *****SPAM***** [TechAssist] Re: SANYO AVM 276A > >>>>> > >>>>>> > >>>>>> I did run for low AC but no change any other help you can give > >>>>>> thanks > >>>>>> > >>>>>> Ken Dinckan > >>>>>> ALL Tv&Appliance Service > >>>>>> 2747 Roosevelt Street # B > >>>>>> Carlsbad CA, 92008 > >>>>>> tel: (760)434-1131 > >>>>>> fax: (760)434-8856 > >>>>>> email to : kdinckan@xxxxxxx > >>>>>> ----- Original Message ----- > >>>>>> From: "Gonzalo Arrivas" <gna2000@xxxxxxx> > >>>>>> To: <techassist@xxxxxxxxxxxxx> > >>>>>> Sent: Wednesday, January 09, 2002 1:42 PM > >>>>>> Subject: [TechAssist] Re: SANYO AVM 276A > >>>>>> > >>>>>> > >>>>>>> > >>>>>>> > >>>>>>> Ken, > >>>>>>> > >>>>>>> Try running it at a lower AC voltage (approx. 90VAC)using a > > variac > >>> on > >>>>> the > >>>>>> TV > >>>>>>> mode and see what happen and let me know. > >>>>>>> > >>>>>>> G.N.Arrivas, CET Pittsburg, CA > >>>>>>> http://www.etechhelponline,com > >>>>>>> > >>>>>>>> From: "Ken Dinckan" <kdinckan@xxxxxxx> > >>>>>>>> Reply-To: techassist@xxxxxxxxxxxxx > >>>>>>>> To: <techassist@xxxxxxxxxxxxx> > >>>>>>>> Subject: [TechAssist] SANYO AVM 276A > >>>>>>>> Date: Wed, 9 Jan 2002 00:33:04 -0800 > >>>>>>>> > >>>>>>>> anyone help for the Sanyo tv shuts down 10-15 minutes when tv > > mode > >>>>>>>> selected. Won't shut down when video inputs selected. Suspected > > IF > >>>>>>>> problem?? > >>>>>>>> > >>>>>>>> ------------------------------------------ > >>>>>>>> Help make your TechAssist database better! > >>>>>>>> Submit your fixes here: > > http://circuitwork.com/techassist/tip/#tips > >>>>>>>> ------------------------------------------ > >>>>>>>> To UNSUBSCRIBE your email address, click here: > >>>>>>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >>>>>>>> Or send a BLANK email with unsubscribe in the > >>>>>>>> SUBJECT field to the address above. > >>>>>>>> > >>>>>>> > >>>>>>> > >>>>>>> > >>>>>>> > >>>>>>> G.N.Arrivas, CET, Pittsburg. CA > >>>>>>> Tel/Fax: 925-432-2057 > >>>>>>> Email: gna2000@xxxxxxx > >>>>>>> > >>>>>>> For Tech Repair Help: > >>>>>>> http://www.etechhelponline.com > >>>>>>> (Now viewed by technicians in 60-plus countries worldwide.) > >>>>>> > >>>>> > >>> > >> ------------------------------------------------------------------------- - > >>>>>>> Tax Help & Services: > >>>>>>> http://www.itaxhelponline.com > >>>>>> > >>>>> > >>> > >> ------------------------------------------------------------------------- > >>>>>>> Business Opportunities & Lifestyle! > >>>>>>> http://www.arrivasenterprises.com > >>>>>>> > >>>>>>> > >>>>>>> > > _________________________________________________________________ > >>>>>>> MSN Photos is the easiest way to share and print your photos: > >>>>>>> http://photos.msn.com/support/worldwide.aspx > >>>>>>> > >>>>>>> ------------------------------------------ > >>>>>>> Help make your TechAssist database better! > >>>>>>> Submit your fixes here: > > http://circuitwork.com/techassist/tip/#tips > >>>>>>> ------------------------------------------ > >>>>>>> To UNSUBSCRIBE your email address, click here: > >>>>>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >>>>>>> Or send a BLANK email with unsubscribe in the > >>>>>>> SUBJECT field to the address above. > >>>>>>> > >>>>>>> > >>>>>> > >>>>>> > >>>>>> ------------------------------------------ > >>>>>> Make your TechAssist database better! > >>>>>> Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > >>>>>> ------------------------------------------ > >>>>>> To UNSUBSCRIBE your email address, click here: > >>>>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >>>>>> Or send a BLANK email with unsubscribe in the > >>>>>> SUBJECT field to the address above. > >>>>>> > >>>>>> > >>>>> > >>>>> ------------------------------------------ > >>>>> Make your TechAssist database better! > >>>>> Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > >>>>> ------------------------------------------ > >>>>> To UNSUBSCRIBE your email address, click here: > >>>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >>>>> Or send a BLANK email with unsubscribe in the > >>>>> SUBJECT field to the address above. > >>>> > >>>> -- > >>>> ------------------------------------------ > >>>> Make your TechAssist database better! > >>>> Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > >>>> ------------------------------------------ > >>>> To UNSUBSCRIBE your email address, click here: > >>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >>>> Or send a BLANK email with unsubscribe in the > >>>> SUBJECT field to the address above. > >>>> > >>>> > >>> > >>> ------------------------------------------ > >>> Make your TechAssist database better! > >>> Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > >>> ------------------------------------------ > >>> To UNSUBSCRIBE your email address, click here: > >>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >>> Or send a BLANK email with unsubscribe in the > >>> SUBJECT field to the address above. > >> > >> -- > >> ------------------------------------------ > >> Make your TechAssist database better! > >> Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > >> ------------------------------------------ > >> To UNSUBSCRIBE your email address, click here: > >> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >> Or send a BLANK email with unsubscribe in the > >> SUBJECT field to the address above. > >> > >> > > > > > > ------------------------------------------ > > Make your TechAssist database better! > > Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > > ------------------------------------------ > > To UNSUBSCRIBE your email address, click here: > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > Or send a BLANK email with unsubscribe in the > > SUBJECT field to the address above. > > > > -- > From: Ed Gaidies > teltek@xxxxxxxxxxx > Tel-Tek Electronics > > ------------------------------------------ > Make your TechAssist database better! > Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > ------------------------------------------ > To UNSUBSCRIBE your email address, click here: > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > Or send a BLANK email with unsubscribe in the > SUBJECT field to the address above. > > > ------------------------------------------ Make your TechAssist database better! Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ ------------------------------------------ To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe Or send a BLANK email with unsubscribe in the SUBJECT field to the address above.