It won't run. It tries to start but just shuts down. Standby voltages seen normal until I hit the power button. As I measure standby voltages when I turn the set on, they drop about half. Neil > ** Original Subject: [TechAssist] Re: RCA ProJo PTK169PABS > ** Original Sender: Dennis Viereck <wa6ati@xxxxxxxxxxxxxx> > ** Original Date: Wed, 21 Nov 2001 00:37:05 -0500 (EST) > ** Original Message follows... > > Neil: > Is the voltage you are measuring in the Standby mode or in the Run mode? > > If so, What are the voltages at CR4106(K) & CR4101(K) with respect to hot > ground in the Standby mode? Are any of the supply voltages pulsing at a 0.5 > to 1 second rate at U4101(15 & 16) > > Dennis Viereck > > > tvdoctors@xxxxxxxxxxxxx wrote: > > > Didn't help! 130 goes to around 70. 12.6 goes to around 6.5 _15 and > > positive 15 don't seem to go as low. Anything else to try. I do get a > > spark like from a spark plug wire from the anode for about a second when > > power button is hit. Neil > > > > > ** Original Subject: [TechAssist] Re: RCA ProJo PTK169PABS > > > ** Original Sender: "Ron Miller" <rlmbkm@xxxxxxxx> > > > ** Original Date: Tue, 20 Nov 2001 18:32:32 -0500 (EST) > > > > > ** Original Message follows... > > > > > > > > B+ should be 143.5vdc change two caps to the left of U4101 a 2.2uf@100v > > > and > > > a 15uf @ 63v.,also check C4108 in base circuit of chopper. > > > Ron Miller > > > D.T.V. Texas > > > > > > ----- Original Message -----From: <tvdoctors@xxxxxxxxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Tuesday, November 20, 2001 5:03 PM > > > Subject: [TechAssist] RCA ProJo PTK169PABS > > > > > > > > > > OK here's the deal: I brought this projector module into my shop and > > > found R767U open and R763U to be discolored. I replaced these with the > > > high > > > voltage splitter and checked other surrounding components. Set still won't > > > activate. My B+ is 130 volts and all other secondary voltages are right on > > > the track. I have a good pulse to the base of the horiz.. Output > > > transistor. > > > When I push the power button, I notice that the 130 volts gets loaded down > > > to around 70 volts. If I disconnect the anode lead from the splitter and > > > clip a lead from about a tenth of an inch from the lead to ground, it > > > makes > > > a spark once then shuts down, so I know my high voltage is trying to come > > > up, but shuts down. I've checked the caps in the horiz.output collector > > > circuit and they check good. The only thing I can find out of place is my > > > 130 volt line is dropping down. Has anyone had a problem like this in the > > > past? Could it be the flyback? Thanks for input on this. My customer > > > would like to have this set back before Thanksgiving. Neil > > > > > > > > TV Doctors 108 W. Main St. Monroe,Wa. 98272 360-794-6469 > > > > > > > > ================================= > > > > Help make your TechAssist database better! > > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > > ================================= > > > > To UNSUBSCRIBE your email address, click here: > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > > > > > > > > > > > > ================================= > > > Help make your TechAssist database better! > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > ================================= > > > To UNSUBSCRIBE your email address, click here: > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > >** --------- End Original Message ----------- ** > > > > > > > > > TV Doctors 108 W. Main St. Monroe,Wa. 98272 360-794-6469 > > > > ================================= > > Help make your TechAssist database better! > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > ================================= > > To UNSUBSCRIBE your email address, click here: > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > ================================= > Help make your TechAssist database better! > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > ================================= > To UNSUBSCRIBE your email address, click here: > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >** --------- End Original Message ----------- ** > TV Doctors 108 W. Main St. Monroe,Wa. 98272 360-794-6469 ================================= Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips ================================= To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe