[TechAssist] Re: RCA G35772AT CTC187CL DEAD/More info
- From: "Tel-Tek Electronics" <teltek3@xxxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Thu, 30 Sep 2004 14:00:48 -0400
Larry;
Make sure you post your fix...I'm sitting here riding on your shoulders.
I have a CTC187 sitting here for a week, same problem. I set it aside
for now.
-Ed-
Tel-Tek Electronics
Ontario-Canada
teltek3@xxxxxxxxxxxx
teltek@xxxxxxxxx
-----Original Message-----
From: techassist-bounce@xxxxxxxxxxxxx
[mailto:techassist-bounce@xxxxxxxxxxxxx] On Behalf Of Bob@Bobs tv
Sent: Thursday, September 30, 2004 1:42 PM
To: techassist@xxxxxxxxxxxxx
Subject: [TechAssist] Re: RCA G35772AT CTC187CL DEAD/More info
Larry,
Bridge a 1.5m resistor (R4104) so you know for sure...Pin 4
needs a
+ voltage to get the regulator going...
Bob,
Bobs TV Worcester, ma
woodman1@xxxxxxxx
Main 508-853-1482
Fax 508-853-1480
----- Original Message -----
From: "Larry E" <videotech@xxxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Thursday, September 30, 2004 1:21 PM
Subject: [TechAssist] Re: RCA G35772AT CTC187CL DEAD/More info
> Hi Guys, replaced the eprom and still have the same problem, zero
volts on
pin 6,
>
> 4.32 on pin 8&5. Unsoldered pin 54 of U1001 thinking it might have
been
pulling
> it down, no change, Q4105 is supposed to be the 5v standby source? (no
schematic)
>
> I have ( measured to cold ground) E= 4.77 B= 5.1 C= 11.7 volts.
Could
the 4.32
>
> be too low on pins 8 & 5 ? I was told pins 5&6 get the 5 volts from
pin 8
of
> U3201
> so I`m still confused how pin 5 can have 4.32 but pin 6 would be zero
if
the
> source
> is internally from pin 8 even with a new eprom installed, HELP!!!
Larry
E
>
> Larry Eastman
> American TV & Electronics
> Crystal River, Fl. 34428
>
> Larry E wrote:
>
> > Hi Guys, this 187CL is stone dead, no click from relay, HOT is good,
> > have 160 v on collector
> > in standby, resoldered H- driver transformer and the coil, C4107 is
> > good, found a bad
> > C4105 10uf @ 200 replaced it with no change, I need to know if the
> > voltages are correct
> > on U4101 as I don`t have the schematic, they are
> > Pin 1= -40
> > 2= -33
> > 4= 0
> > 5= .9
> > 6= .9
> > 7= .4
> > 8&9 = 0
> > 11&12 = 165 thanks in advance, Larry E
> > Larry Eastman
> > American TV & Electronics
> > Crystal River, Fl. 34428
> >
>
>
------------------------------------------------------------------------
--
---
> > Lost Password:
> > http://www.tech-assist.org and select "Login Problems?".
> > Email Archives:
> > //www.freelists.org/archives/techassist/
>
>
>
------------------------------------------------------------------------
--
---
> Lost Password:
> http://www.tech-assist.org and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/
>
------------------------------------------------------------------------
-----
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
-----------------------------------------------------------------------------
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
Other related posts:
