Those resistor networks can be very interrmittent and may only check bad when set is on. Phillip R Hull STET phil245@xxxxxxxxxxxxx FAX 517--569-3075 Professional Technicians only ----- Original Message ----- From: <myers_tv@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Tuesday, February 10, 2004 12:12 PM Subject: [TechAssist] Re: (RCA) F35670MBFM1 CTC187CN3 extreme fold over vertical! > I have seen this before. Try C4504. > > > John Myers > Myers TV Service Since 1984 > Alliance, OH > ph 330-821-6545 > > ----- Original Message ----- > From: "Jim Bailey" <baileystv@xxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Tuesday, February 10, 2004 10:36 AM > Subject: [TechAssist] Re: (RCA) F35670MBFM1 CTC187CN3 extreme fold over > vertical! > > > > Thanks for the tip Jason,I have already removed it and did a resistance > > check and it added up ok but I wonder if it could brake down as voltage is > > applied? > > > > Jim Bailey > > Bailey's TV Sales & Service > > Buckhannon, WV 26201 > > baileystv@xxxxxxxxxxxx > > > > > > > > > > -----Original Message----- > > From: techassist-bounce@xxxxxxxxxxxxx > > [mailto:techassist-bounce@xxxxxxxxxxxxx]On Behalf Of Mouton's > > Electronics > > Sent: Tuesday, February 10, 2004 10:34 AM > > To: techassist@xxxxxxxxxxxxx > > Subject: [TechAssist] Re: (RCA) F35670MBFM1 CTC187CN3 extreme fold over > > vertical! > > > > > > There is a blue strip looking component, a resistor network, Location > > RN????. Its the only one in the set and is near the vertical IC. I have > had > > that problem several times and usually was the RN. > > > > Hope this helps > > > > Jason > > Moutons Electronics > > > > > > ----- Original Message ----- > > From: "Jim Bailey" <baileystv@xxxxxxxxxxxx> > > To: "TechAssist" <techassist@xxxxxxxxxxxxx> > > Sent: Tuesday, February 10, 2004 9:07 AM > > Subject: [TechAssist] (RCA) F35670MBFM1 CTC187CN3 extreme fold over > > vertical! > > > > > > > This TV has a bright horizontal line through the middle of the picture > > with > > > extreme fold over from the middle to the top part of picture looks like > > > Venetian blinds and no picture from the middle down to the bottom. > > > I have replaced the vertical IC with no change in the picture; I have > ESR > > > the capacitors in the vertical circuit and can't find any bad ones yet, > > > there is a 12volt line being dragged down to about 7 volts. > > > I am getting ready to check the pincushion board next but wondered if > > > anybody has seen this problem before. > > > Any help would be appreciated! > > > > > > Jim Bailey > > > Bailey's TV Sales & Service > > > Buckhannon, WV 26201 > > > baileystv@xxxxxxxxxxxx > > > > > > > > > > > > > > > > -------------------------------------------------------------------------- > > --- > > > Lost Password: > > > http://www.tech-assist.org and select "Login Problems?". > > > Email Archives: > > > //www.freelists.org/archives/techassist/ > > > > > > > > -------------------------------------------------------------------------- > -- > > - > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > > > > -------------------------------------------------------------------------- > --- > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > -------------------------------------------------------------------------- --- > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ > > ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/