Actually, they are "pre-programmed" with average values. The other option is to purchase a "blank" eeprom (not programmed at all) if you have your own eeprom programmer and program yourself. Gary McCartney McCartney Electronics 7134 Fife Rd, RR 7 Guelph Ontario Canada N1H 6J4 Fax: (519)821-1530 email: gary (at) number63.ca "Phillip R. Hull" wrote: > > Once and for all( I hope), these IC's are not preprogramed, they are set > with average values, also the tuner will have to be realigned with Chipper > Check, unless you can write down all the tuner parameters before replacing. > Phillip R Hull STET > phil245@xxxxxxxxxxxxx > ----- Original Message ----- > From: "Kevin" <kevintv@xxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Wednesday, January 22, 2003 3:31 PM > Subject: [TechAssist] Re: Need refresher on RCA EEPROM replacing...] > > > > > Sometimes the data is corrupted. Then your only option is to get a > > preprogrammed eeprom. They are available form Main Electronics in > > Vancouver BC Canada. 250-872-0267 Ask for Mike or Daniel. You may > > still have to adjust the tuner parameters to get a good picture on all > > channels. > > > > Kevin Wilks > > Kevin's TV & Video Repair > > Penticton BC Canada > > kevintv@xxxxxxx > > > > > > -----Original Message----- > > From: techassist-bounce@xxxxxxxxxxxxx > > [mailto:techassist-bounce@xxxxxxxxxxxxx] On Behalf Of Philip Bader > > Sent: Wednesday, January 22, 2003 6:04 AM > > To: techassist@xxxxxxxxxxxxx > > Subject: [TechAssist] Re: Need refresher on RCA EEPROM replacing...] > > > > > > Not to drag this on,but I remember trying this.Probably didn't do the > > right sequence,but all I managed to do was transfer the old corrupt > > parameters to the new "blank" chip,so now I have two exact chips with > > corrupt data. > > How does it transfer the "good" data without also the bad? > > Phil Bader > > > > Jeff Dougherty wrote: > > > > > > Harlan, > > > Place old EEPROM in socket, turn set on, replace old EEPROM with new > > one. > > > I have had luck with ordering the correct EEPROM for the specific > > chassis and all > > > I have to adjust, if anything, is the horizontal freq. > > > support@xxxxxxxxxxxxxxxxxx > > > FAX 717-564-4952 > > > Jeff Dougherty > > > Intrepid Video & Electronics Be careful of your thoughts. > > > 501 Luther Rd They may become your words > > > Harrisburg, PA 17111 any moment. > > > 717-909-8844 > > > VCR tips, electronics info & general interest. > > > www.intrepid-video.com www.tech-repair.net > > > www.thetoolcaddy.com www.9-11-2001tragedy.com > > > > > *********************************************************************** > > > > > > ----- Original Message ----- > > > From: "Philip Bader" <tjanphyl@xxxxxxxxxxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Tuesday, January 21, 2003 10:57 AM > > > Subject: [TechAssist] Need refresher on RCA EEPROM replacing...] > > > > > > I forwarded this to the group for a tech. PLease help. > > > Phil Bader > > > Hi, > > > Have here an RCA CTC 177 and suspect bad eeprom chip as the set will > > > not power on and have check all the ususal "stuff" ... standby > > > supplies, etc. > > > > > > Question is... was there a procedure when putting in the new eeprom > > > where you put in a socket also and then can extract the parameters > > > yet from the "bad" one so as not to have to do an entire alignment? > > > > > > If there is such a process, what were the steps? > > > > > > Thanks, > > > Harlan > > > > > > ------------------------------------------ > > > Submit A Repair Tip For Everyone Here: > > > http://www.tech-assist.org/secure/tip/main.html > > > ------------------------------------------ > > > To REMOVE your email address, click here: > > > http://www.tech-assist.org/unsubb.html > > > To CHANGE your email address, click here: > > > http://www.techassist.net/forms/change.html > > > > > > ------------------------------------------ > > > Submit A Repair Tip For Everyone Here: > > > http://www.tech-assist.org/secure/tip/main.html > > > ------------------------------------------ > > > To REMOVE your email address, click here: > > > http://www.tech-assist.org/unsubb.html > > > To CHANGE your email address, click here: > > > http://www.techassist.net/forms/change.html > > > > -- > > Philip Bader > > Jan Phyl TV Inc. (estab. 1976) > > 3420 Recker Hwy. Winter Haven, Fl. 33880 > > Fax (863) 299-8821 > > email: tjanphyl@xxxxxxxxxxxxxxx > > > > ------------------------------------------ > > Submit A Repair Tip For Everyone Here: > > http://www.tech-assist.org/secure/tip/main.html > > ------------------------------------------ > > To REMOVE your email address, click here: > > http://www.tech-assist.org/unsubb.html > > To CHANGE your email address, click here: > > http://www.techassist.net/forms/change.html > > > > ------------------------------------------ > > Submit A Repair Tip For Everyone Here: > > http://www.tech-assist.org/secure/tip/main.html > > ------------------------------------------ > > To REMOVE your email address, click here: > > http://www.tech-assist.org/unsubb.html > > To CHANGE your email address, click here: > > http://www.techassist.net/forms/change.html > > > > > > > > ------------------------------------------ > Submit A Repair Tip For Everyone Here: > http://www.tech-assist.org/secure/tip/main.html > ------------------------------------------ > To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html > To CHANGE your email address, click here: > http://www.techassist.net/forms/change.html -- ------------------------------------------ Submit A Repair Tip For Everyone Here: http://www.tech-assist.org/secure/tip/main.html ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html To CHANGE your email address, click here: http://www.techassist.net/forms/change.html