[TechAssist] Re: Magnavox PTV350 need resistor value
- From: "Terry J Hutchison" <sony1@xxxxxxxx>
- To: "techassist@xxxxxxxxxxxxx" <techassist@xxxxxxxxxxxxx>,"techassist@xxxxxxxxxxxxx" <techassist@xxxxxxxxxxxxx>
- Date: Wed, 31 Dec 2003 16:36:10 -0500
Thanks for taking the time to help. That resistor finished up the job.
Happy New Year and thanks again. Terry
> [Original Message]
> From: Phillip R. Hull <phil245@xxxxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Date: 12/31/03 11:55:29 AM
> Subject: [TechAssist] Re: Magnavox PTV350 need resistor value
>
> R45 is 560 ohm 1/4 Watt R41 is 7.5 K 1/4 Watt
> Phillip R Hull STET
> phil245@xxxxxxxxxxxxx
> FAX 517--569-3075
> Professional Technicians only
> ----- Original Message -----
> From: "Terry J Hutchison" <sony1@xxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>; <techassist@xxxxxxxxxxxxx>
> Sent: Wednesday, December 31, 2003 11:30 AM
> Subject: [TechAssist] Re: Magnavox PTV350 need resistor value
>
>
> > Appreciate your time, this resistor is on the convergence wave form
board,
> > over half the components on this board only have two numbers this
> > resistor(R45) is connected by trace path to JU2and R46 at one end the
> other
> > end looks like a ground and R41 goes to pin 13 of IC3. I just assume
this
> > module could be like a lot of RCA chasis and leave off the beginning
> > numbers in some locations. The only three digit markings on this module
> > begin with 1 ie R190. Hope this is enough and I really appreciate the
> > help. Terry
> >
> >
> > > [Original Message]
> > > From: Larry E. <videotech@xxxxxxxxxxxx>
> > > To: <techassist@xxxxxxxxxxxxx>
> > > Date: 12/31/03 10:36:36 AM
> > > Subject: [TechAssist] Re: Magnavox PTV350 need resistor value
> > >
> > > Terry, According to NAP service manual all resistors are 3 digits,
> > re-check number, if it is 2 digits
> > > give me location, (tied to which parts) and I`ll check the schematic
and
> > try to find it for you, LarryE
> > > Larry Eastman
> > > American TV & Electronics
> > > Crystal River, Fl. 34428
> > >
> > > Terry J Hutchison wrote:
> > >
> > > > Set came in with no filiment but had HV, replaced C455 restored
> > filiment volts but have burned resistor on deflection board need value
> > cannot read it is R45. Thanks in advance for any help. Terry
> > > >
> > > > Terry J Hutchison
> > > > sony1@xxxxxxxx
> > > > Why Wait? Move to EarthLink.
> > > >
> > > >
> >
>
****************************************************************************
> > *
> > > > Lost Password:
> > > > http://www.tech-assist.org and select "Login Problems?".
> > > > Email Archives:
> > > > //www.freelists.org/archives/techassist/
> > >
> > >
> >
>
****************************************************************************
> > *
> > > Lost Password:
> > > http://www.tech-assist.org and select "Login Problems?".
> > > Email Archives:
> > > //www.freelists.org/archives/techassist/
> >
> >
> >
>
****************************************************************************
> *
> > Lost Password:
> > http://www.tech-assist.org and select "Login Problems?".
> > Email Archives:
> > //www.freelists.org/archives/techassist/
> >
> >
>
>
****************************************************************************
*
> Lost Password:
> http://www.tech-assist.org and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/
*****************************************************************************
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
Other related posts:
