Thank's very much for the input Ed. I found the following voltages: Approx 35vdc @ pin 3 and pin 6, 2vdc @ pin 4. All looks good there. However upon inspection I did find a burnt resistor (r2200) 1/4 w adjacent to Q2023. It's tucked away under the tuner and not too far from the PIP module. Do you show a value for it in your service guide? Any input is appreciated. Thanks! Check For 2vdc At Pin 4 Ic401,If Missing Check For 34vdc At Pin 6 And 3 Lso Check For .8vpp Pulse At Pin 5, If All Are Present Check 14v R Cut and Pasted from Winstips. -Ed- Tel-Tek Electronics Ontario-Canada teltek2@xxxxxxxxxxxx ----- Original Message ----- From: "teltek2" <teltek2@xxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Saturday, December 28, 2002 11:10 AM Subject: [TechAssist] Re: MITSUBISHI PROJ TV MDL: VS-5051 / NO VIDEO > Are you sure the IC is suppose to be LA7845? > > -Ed- > Tel-Tek Electronics > Ontario-Canada > > teltek2@xxxxxxxxxxxx > ----- Original Message ----- > From: <fremur01@xxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Saturday, December 28, 2002 10:49 AM > Subject: [TechAssist] Re: MITSUBISHI PROJ TV MDL: VS-5051 / NO VIDEO > > > > > > Hello, > > > > This one is still being a problem. > > > > I replaced IC401 (LA7845) along with adjoining > > caps in the circuit and it still has no video. Crt > > filaments and HV are fine. I tried inspecting the yoke > > connectors as well. > > > > Anyway, does anyone with service literature know the > > correct Vcc voltages on the IC I should look for in > > the vertical circuit? This is an awkward pc board > > so measurements should be fun. > > > > Thanks > > > > Item specs: MITSUBISHI PROJ TV MDL: VS-5051 > > > > Fred > > MTS Electronics > > Fayetteville, NC > > fremur01@xxxxxxxxx > > > > -----Original Message----- > > From: techassist-bounce@xxxxxxxxxxxxx > > [mailto:techassist-bounce@xxxxxxxxxxxxx]On Behalf Of > > Gooseman > > Sent: Wednesday, December 11, 2002 9:20 PM > > To: techassist@xxxxxxxxxxxxx > > Subject: [TechAssist] Re: MITSUBISHI PROJ TV MDL: > > VS-5051 / NO VIDEO > > > > > > > > Look at ic401 for loose connection or the yokes.you > > can wiggle the youe > > plugs and usually find the 1 with the loose > > connection. > > Beyond that you may have a bad vertical IC. > > Tvman99@xxxxxxx > > > > > > -----Original Message----- > > From: techassist-bounce@xxxxxxxxxxxxx > > [mailto:techassist-bounce@xxxxxxxxxxxxx] On Behalf Of > > fremur01@xxxxxxxxx > > Sent: Wednesday, December 11, 2002 4:36 PM > > To: techassist@xxxxxxxxxxxxx > > Subject: [TechAssist] MITSUBISHI PROJ TV MDL: VS-5051 > > / NO VIDEO > > > > > > Hello, > > > > Went on a call today for the following: Set has good > > audio but no picture. I noticed all CRT filaments > > light up along with H/V buildup. One Tech had > > mentioned that some of these sets can have problems > > with the PIP module. > > > > Anyway, I was limited as to what could be done on > > site, and will take set back to shop later this week. > > > > I dont have service literature for this one. Nothing > > looked burnt on the PIP module. Anyone know of case > > history info for this model? > > > > Thanks > > > > Fred > > MTS Electronics > > Fayetteville, NC > > fremur01@xxxxxxxxx > > > > > > Item specs: MITSUBISHI PROJ TV MDL: VS-5051 __________________________________________________ Do you Yahoo!? Yahoo! Mail Plus - Powerful. Affordable. Sign up now. http://mailplus.yahoo.com ------------------------------------------ Submit A Repair Tip For Everyone Here: http://www.tech-assist.org/secure/tip/main.html ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html To CHANGE your email address, click here: http://www.techassist.net/forms/change.html