[TechAssist] Re: Goldstar GCV1924M TV/VCR - mechanism problem-Further
- From: "Roger G./Mr Fix-It" <rogerfixit@xxxxxxxxxxx>
- To: TECHASSIST <techassist@xxxxxxxxxxxxx>
- Date: Sun, 20 Nov 2005 01:48:18 -0500
Changed the motor driver IC (BA6209 type) but nothing changed.
Do not get voltage to load motor.
About to blame micro and bag it unless someone has another idea.
TIA
Roger G.
Mr. Fix-It Harrisburg, PA 17110
WebSite- http://mrfixit.netfirms.com
Alternate - rogerfixit@xxxxxxxx
FAX 510-740-3641; Tel: 717-540-0799 (shop)
Roger G./Mr Fix-It wrote:
> Chris-
> I appreciate your taking the time to post. I did rotate the load mtr off
> of stop but it never moved at all. I think there is one of those 10-pin
> motor drive IC's which I can check. Problem with this unit- unlike some
> where you can power up the VCR separately, it is awkward to troubleshoot
> - but somebody has to do it !!
> Roger G.
>
> Mr. Fix-It Harrisburg, PA 17110
> WebSite- http://mrfixit.netfirms.com
> Alternate - rogerfixit@xxxxxxxx
> FAX 510-740-3641; Tel: 717-540-0799 (shop)
>
> Christopher Barnak wrote:
>> Roger,
>> After re-reading your post. Maybe it is the Micro.
>> But, many combo's will not come on until the stop
>> or eject mode is correct. So if the mode switch is manually set to
>> stop and it still does not come on,
>> then I would suspect the micro, BUT check the power
>> supply, micro oscillator, B+ to micro and the reset pin
>> to make sure it is normal. I suspect a missing voltage,
>> as the Micro failure is rare and I've been bit by it so many
>> times, only to find out it was something other than the Micro.
>> But, it still could be the Micro.
>>
>> Chris
>>
>>
>>
>>>>> cbarnak@xxxxxxxxxxxxx 11/10/05 7:28 AM >>>
>> Maybe the load motor SHOULD BE running and it can't
>> because there is no voltage supplied to it.
>> Unplug set. Rotate the motor to move the guideposts up alittle to
>> put the mechanism in a position that the unit would normally try to
>> reset to the stop postion upon plug in.
>>
>> If the unit does not try to correct itself, then check the
>> voltage being supplied to the load motor. It should be
>> there and ususally about 12 volts.
>>
>> If not, then check that the Micro is actually telling the loading
>> motor IC to do it's job. If you do not have the
>> schematic, then look up an equivalent IC in the NTE
>> book and find what pins are the control pins.
>>
>> If the IC does not get a control signal from the Micro,
>> then either the micro is partially not working or look
>> for the most overlooked - A broken pattern.
>>
>> You may already know all this stuff, but I'm just
>> writing it in case you don't.
>>
>> Good Luck,
>>
>> Chris
>>
>>
>>
>>>>> rogerfixit@xxxxxxxxxxx 11/09/05 7:04 PM >>>
>> Load motor does NOT run; take up reel does.
>> Resoldered sensor board; reconditioned mode switch; cleaned surfaces
>> on
>>
>> reels - no difference.
>> Note = power switch has no effect and TV does not come on either.
>> Starting to suspect micro problem.
>>
>> Anything else ??
>> Thanx
>> Roger G.
>>
>> Mr. Fix-It Harrisburg, PA 17110
>> WebSite- http://mrfixit.netfirms.com Alternate - rogerfixit@xxxxxxxx
>> FAX 510-740-3641; Tel: 717-540-0799 (shop)
>>
>> Christopher Barnak wrote:
>>> Roger,
>>> If the loading motor runs when set is plugged in, then the cassette
>>> load or tape load mechanism is bound up and the mode switch never
>>> reachs the stop or eject position.
>>> Could be the mode switch, I refurbish almost all mode switchs
>>> on units that come in with a control type of problem.
>>> And I If the load motor does not run, but the unit takeup reel
>>> turns on power up, then I would suspect that the unit
>>> has a reel sensor under the supply reel and it is not working. It is
>>> common in many VCR's for the Micro to
>>> run the takeup reel and then look for a pulse from the
>>> the supply reel sensor. This is to make sure no slack
>>> is in the tape. (Remember the Sharps that would not
>>> eject a broken tape).
>>>
>>>
>>> Christopher Barnak, CET
>>> Norfolk Public Schools
>>> Electronics Maintenance
>>> 966 Bellmore Ave.
>>> Norfolk, Va. 23504
>>>
>>> Phone 757 628 3385
>>> Fax 757 628 3392
>>> cbarnak@xxxxxxxxxxxxx
>>>
>>>>>> rogerfixit@xxxxxxxxxxx 11/08/05 10:37 PM >>>
>>> Goldstar GCV1924M Combo
>>> Problem- Customer said was playing a tape then stopped. Tape is
>> stuck.
>>> I found unit in full load condition with tape broken and all of it
>> on
>>
>>> take-up reel. Power-on starts takeup reel turning.
>>> Ran load motor (with external power) to eject tape and reset unit.
>>> Reattached to unit expecting it to work BUT - all that happens is
>>> takeup reel turns - power button or eject btns do not function.
>>>
>>> Pulled tape transport. Checked alignment; bottom slider; mode switch
>>
>>> sensor circuit board - all looked ok. Load motor is ok - ran it to
>>> eject.
>>
>
--
-----------------------------------------------------------------------------
This Email List is accessible to the general public through search engines.
Remove: http://www.tech-assist.org/remove.htm
Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation
Lost Password: http://www.tech-assist.org and select "Login Problems?".
Email Archives: //www.freelists.org/archives/techassist/
Other related posts:
