[TechAssist] Re: [Fwd: RCA F25216WT, CTC185AB dead,bad HOT,regulator,open R103U.]

  • From: "albert marquardt" <ampm@xxxxxxx>
  • To: <techassist@xxxxxxxxxxxxx>
  • Date: Sat, 6 Oct 2001 09:42:19 -0700

t4401 primary is pins 2 and 10
al marquardt
ampm@xxxxxxx
----- Original Message -----
From: <damon101@xxxxxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Saturday, October 06, 2001 3:29 AM
Subject: [TechAssist] Re: [Fwd: RCA F25216WT, CTC185AB dead,bad
HOT,regulator,open R103U.]


>
> Heh, glad I'm not the only one......
>
> Damon Brunger
> damon101@xxxxxxxxxxxxxx
> Telrad Electronic Services
> Ft Wayne, IN 46815
>
> ----- Original Message -----
> From: "Phil Bader" <philbad@xxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Friday, October 05, 2001 10:48 AM
> Subject: [TechAssist] Re: [Fwd: RCA F25216WT, CTC185AB dead,bad
> HOT,regulator,open R103U.]
>
>
> >
> > Dar-Heeeeee I was having a senior moment,guys...I know this stuff!
> >
> > Jim Myers wrote:
> > >
> > > Easy to figure out Phil, just use ohm meter to locate the other
primary
> > > pin(s). There should be no ohms reading to any secondary pin, then
> connect
> > > ringer leads across the primary. Flyback is out of circuit, right?
> > > Jim Myers
> > > jr.myers@xxxxxxxxxxx
> > > ----- Original Message -----
> > > From: "Phil Bader" <philbad@xxxxxxxxxx>
> > > To: <techassist@xxxxxxxxxxxxx>
> > > Sent: Friday, October 05, 2001 8:36 AM
> > > Subject: [TechAssist] [Fwd: RCA F25216WT, CTC185AB dead,bad
> > > HOT,regulator,open R103U.]
> > >
> > > >
> > > >
> > > >
> > > > -------- Original Message --------
> > > > Subject: RCA F25216WT, CTC185AB dead,bad HOT,regulator,open R103U.
> > > > Date: Fri, 05 Oct 2001 09:19:13 -0400
> > > > From: Phil Bader <philbad@xxxxxxxxxx>
> > > > Organization: Jan Phyl TV Inc. Winter Haven, Fl.  Estab. 1976
> > > > To: "CONSUMERELREPAIR-L@xxxxxxxxxxxxxxxxxxxx"
> > > > <CONSUMERELREPAIR-L@xxxxxxxxxxxxxxxxxxxx>
> > > >
> > > > Question: Before I install the reg kit 231523,HOT,resistor,I rang
the
> > > > fly and get "BAD"but want to verify the correct fly pins to ring.
One
> > > > lead on the HOT collector  fly pin ( I assume),and where goes the
> other
> > > > ringer lead? (no schemo).Plse use component reference for
> > > > location.Thx,Phil
> > > > Help make your TechAssist online repair tips
> > > > database better!  Submit your fixes here:
> > > > http://www.circuitwork.com/techassist/tip/#tips
> > > > To unsubscribe write to:
> > > > techassist-request@xxxxxxxxxxxxx
> > > > with  unsubscribe  in the subject line.
> > >
> > > Help make your TechAssist online repair tips
> > > database better!  Submit your fixes here:
> > > http://www.circuitwork.com/techassist/tip/#tips
> > > To unsubscribe write to:
> > > techassist-request@xxxxxxxxxxxxx
> > > with  unsubscribe  in the subject line.
> > Help make your TechAssist online repair tips
> > database better!  Submit your fixes here:
> > http://www.circuitwork.com/techassist/tip/#tips
> > To unsubscribe write to:
> > techassist-request@xxxxxxxxxxxxx
> > with  unsubscribe  in the subject line.
> >
>
> Help make your TechAssist online repair tips
> database better!  Submit your fixes here:
> http://www.circuitwork.com/techassist/tip/#tips
> To unsubscribe write to:
> techassist-request@xxxxxxxxxxxxx
> with  unsubscribe  in the subject line.
>

Help make your TechAssist online repair tips 
database better!  Submit your fixes here: 
http://www.circuitwork.com/techassist/tip/#tips
To unsubscribe write to:
techassist-request@xxxxxxxxxxxxx 
with  unsubscribe  in the subject line.

Other related posts:

  1. Home
  2. techassist
  3. Archive
  4. 10-2001