well on the back of the cabinet it says rca ,but on the inside it is a Daewoo . the circuitry has no similarities to any rca I ever worked on. ----- Original Message ----- From: "al m" <ampm@xxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Friday, October 31, 2003 11:23 AM Subject: [TechAssist] Re: Fw: RCA model#F19430 ) chassis# CN-001N set dead > That isn't RCA. > Al Marquardt > ampm@xxxxxxx > Al Marquardt Electronic Repair > 206 W Main > Girardville Pa. 17935 > ----- Original Message ----- > From: "junior hurdle" <jselectronics@xxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Friday, October 31, 2003 10:15 AM > Subject: [TechAssist] Fw: RCA model#F19430 ) chassis# CN-001N set dead > > > > ----- Original Message ----- > > From: junior hurdle > > To: techassist@xxxxxxxxxxxxx > > Sent: Friday, October 31, 2003 11:12 AM > > Subject: Fw: RCA model#F19430 ) chassis# CN-001N set dead > > > > > > I made a mistake and put ctc156 in my last email instead of the chassis # > for this set > > this is a newer set Chassis # CN-001N. > > ----- Original Message ----- > > From: junior hurdle > > To: techassist@xxxxxxxxxxxxx > > Sent: Thursday, October 30, 2003 11:10 PM > > Subject: Fw: RCA model#F19430 CHISSIS #CN-001N set dead > > > > > > sorry I forgot to sign this email > > Junior hurdle. > > Owner > > J'S electronics (est 1995) > > St. Michael > > Barbados > > Phone :(246)-4298535 > > email: jselectronics@xxxxxxxxxxxx > > > > ----- Original Message ----- > > From: junior hurdle > > To: techassist@xxxxxxxxxxxxx > > Sent: Thursday, October 30, 2003 11:03 PM > > Subject: RCA model#F19430 (ctc156B) set dead > > > > > > hi techs. > > I have had worked a few of these RCA mod# F19430 sets that were dead. > > normally the reg is shorted . But with this one the reg is good , and you > can hear the > > power supply start up when you plug it in.when I switch it on all happens > is the degaussing > > relay cuts in for a few secs but nothing else . it has the 5v for the > eeprom and the sys control . > > this set carries a GCT841B ic for the signal and deflection and I am not > familiar with this ic. > > can any one tell me if there is suppose to be a standby voltage on this ic > , or Evan the pin out > > for this . > > > **************************************************************************** > * > > Classifieds! Buy or Sell! > > http://sell.tech-assist.org > > The Tech Address Book: > > http://www.tech-assist.org/secure/tip/contact.htm > > Add a Repair Tip Here, or Change/Remove your Email Address: > > http://www.tech-assist.org/secure/tip/main.htm > > Lost Password: > > http://www.tech-assist.org and select "Lost your Login Info?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > > > > > **************************************************************************** * > Classifieds! Buy or Sell! > http://sell.tech-assist.org > The Tech Address Book: > http://www.tech-assist.org/secure/tip/contact.htm > Add a Repair Tip Here, or Change/Remove your Email Address: > http://www.tech-assist.org/secure/tip/main.htm > Lost Password: > http://www.tech-assist.org and select "Lost your Login Info?". > Email Archives: > //www.freelists.org/archives/techassist/ > > ***************************************************************************** Classifieds! Buy or Sell! http://sell.tech-assist.org The Tech Address Book: http://www.tech-assist.org/secure/tip/contact.htm Add a Repair Tip Here, or Change/Remove your Email Address: http://www.tech-assist.org/secure/tip/main.htm Lost Password: http://www.tech-assist.org and select "Lost your Login Info?". Email Archives: //www.freelists.org/archives/techassist/