[TechAssist] Re: Fw: RCA P60920BL (CTC195K) Vertical Problems
- From: "Shaun" <satguy@xxxxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Mon, 13 Sep 2004 17:46:43 -0600
Never mind found them surface mount.
Shaun
Advanced Electronics
224 West Riverview Ave.
Fort Morgan, CO 80701
----- Original Message -----
From: "Shaun" <satguy@xxxxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Monday, September 13, 2004 5:24 PM
Subject: [TechAssist] Re: Fw: RCA P60920BL (CTC195K) Vertical Problems
> Can you give me a general location for C14501 and C14503 I can't find them
> on the board.
>
> Shaun
>
> Advanced Electronics
> 224 West Riverview Ave.
> Fort Morgan, CO 80701
> ----- Original Message -----
> From: "tvservice" <tvservice@xxxxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Monday, September 13, 2004 1:18 PM
> Subject: [TechAssist] Re: Fw: RCA P60920BL (CTC195K) Vertical Problems
>
>
> > try this
> > CTC/PTK195
> > No Vertical deflection all output parts seem OK
> > replace C14501 and C14503 off pin 16 U16201
> > Also check CR14703 and R14705 +13 volt supply off flyback
> > Robert
> > tvservice@xxxxxxxxxxxxx
> > H & H Electronics Inc
> >
> >
> > ----- Original Message -----
> > From: "Shaun" <satguy@xxxxxxxxxxxxx>
> > To: "tech" <techassist@xxxxxxxxxxxxx>
> > Sent: Monday, September 13, 2004 12:02 PM
> > Subject: [TechAssist] Fw: RCA P60920BL (CTC195K) Vertical Problems
> >
> >
> > > Well this set still does the same thing even after replacing several
> parts
> > > in the vertical section that are listed below. Has anyone seen this
> > chassis
> > > do this? It works fine for about 2 or 3 hours then is starts to shrink
> > down
> > > to a line.
> > >
> > > Shaun
> > >
> > > Advanced Electronics
> > > 224 West Riverview Ave.
> > > Fort Morgan, CO 80701
> > > ----- Original Message -----
> > > From: "Shaun" <satguy@xxxxxxxxxxxxx>
> > > To: "tech" <techassist@xxxxxxxxxxxxx>
> > > Sent: Sunday, September 12, 2004 6:13 PM
> > > Subject: RCA P60920BL (CTC195K) Vertical Problems
> > >
> > >
> > > > This set will run for up to 2 hours fine then the picture will start
> to
> > > > shrink from the bottom first till it is just a line in the middle of
> the
> > > > screen. I replace the vertical IC (U14501) and C14505 (35 v 220 uf)
> > along
> > > > with R14502 (220 ohm 1 watt). I need the value of R14512, when I
> freeze
> > > > spray around R14512 which is very discolored, the set goes back to
> > normal
> > > > operation. I also need the value of R14305, it is also discolored.
> > Thanks
> > > > for any help and any other tips someone might have.
> > > >
> > > > Shaun
> > > >
> > > > Advanced Electronics
> > > > 224 West Riverview Ave.
> > > > Fort Morgan, CO 80701
> > > >
> > >
> > >
> >
>
> --------------------------------------------------------------------------
> > ---
> > > Lost Password:
> > > http://www.tech-assist.org and select "Login Problems?".
> > > Email Archives:
> > > //www.freelists.org/archives/techassist/
> >
> >
> >
>
> --------------------------------------------------------------------------
> ---
> > Lost Password:
> > http://www.tech-assist.org and select "Login Problems?".
> > Email Archives:
> > //www.freelists.org/archives/techassist/
>
>
> --------------------------------------------------------------------------
---
> Lost Password:
> http://www.tech-assist.org and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/
-----------------------------------------------------------------------------
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
Other related posts:
