Good troubleshooting Bill! Bob Waterman, CET® #RI-28 Master Technician License #9109 Service Manager Gemini Computer, TV, & Security Alarms (508)695-7302 (508)695-7769 FAX geminitv@xxxxxxxxxxxxxxxx geminitv@xxxxxxx ----- Original Message ----- From: "Bill Boyd" <billstvs@xxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Wednesday, January 22, 2003 6:24 PM Subject: [TechAssist] FIXED Philips PC6220 C121 Ch 20U6 Channel One set, shuts down > > B+and high voltage were normal so I lifted one end of R273 to disable shut > down. > Found Q540 one of the shutdown transistors shorted, still shut down with > signal. > Second time testing everything found Z564 15V zener diode (over beam current > protection circuit) checked good but zenered at a lower voltage. > Replacing Q540 and Z564 restored normal operation. > > Bill > Bill's TV Service > Sulphur Springs, TX > > >From: "Gemini Computer & TV" <geminitv@xxxxxxxxxxxxxxxx> > >To: <techassist@xxxxxxxxxxxxx> > >Subject: [TechAssist] Re: Philips PC6220 C121 Ch 20U6 Channel One set, > >shuts down > >Date: Tue, 21 Jan 2003 13:41:11 -0500 > > > >That sounds like it may be going into high voltage shutdown. What does the > >B+ measure? Do you have the option of switching to an A/V input? > > > >Bob Waterman, CET® #RI-28 > >Master Technician License #9109 > >Service Manager > >Gemini Computer, TV, & Security Alarms > >(508)695-7302 > >(508)695-7769 FAX > >geminitv@xxxxxxxxxxxxxxxx > >geminitv@xxxxxxx > > > >----- Original Message ----- > >From: "Bill Boyd" <billstvs@xxxxxxxxxx> > >To: <techassist@xxxxxxxxxxxxx> > >Sent: Tuesday, January 21, 2003 11:52 AM > >Subject: [TechAssist] Philips PC6220 C121 Ch 20U6 Channel One set, shuts > >down > > > > > > > > > > Philips model PC6220 C121 > > > Chassis 20U6 > > > Commercial model used as a Channel One monitor > > > > > > First time working on one of these. > > > Set came in with bright screen with retrace lines. > > > Replaced open R562 and burnt R573. > > > Now have normal screen with snow with no signal. > > > OSD is normal. > > > When I connect a signal or tune to an active channel it > > > shuts down immediately. > > > Is this normal without the Channel One receiver connected > > > or do I have a problem? > > > High voltage and B+ are normal. Shuts down with CRT socket > > > disconnected. Tried with Channel One input card unplugged also. > > > > > > TIA > > > Bill > > > Bill's TV Service > > > Sulphur Springs, TX > > > > > > > > > > > > > > > ------------------------------------------ > > > Submit A Repair Tip For Everyone Here: > > > http://www.tech-assist.org/secure/tip/main.html > > > ------------------------------------------ > > > To REMOVE your email address, click here: > > > http://www.tech-assist.org/unsubb.html > > > To CHANGE your email address, click here: > > > http://www.techassist.net/forms/change.html > > > > > > > > > >------------------------------------------ > >Submit A Repair Tip For Everyone Here: > >http://www.tech-assist.org/secure/tip/main.html > >------------------------------------------ > >To REMOVE your email address, click here: > > http://www.tech-assist.org/unsubb.html > >To CHANGE your email address, click here: > > http://www.techassist.net/forms/change.html > > > ------------------------------------------ > Submit A Repair Tip For Everyone Here: > http://www.tech-assist.org/secure/tip/main.html > ------------------------------------------ > To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html > To CHANGE your email address, click here: > http://www.techassist.net/forms/change.html > > ------------------------------------------ Submit A Repair Tip For Everyone Here: http://www.tech-assist.org/secure/tip/main.html ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html To CHANGE your email address, click here: http://www.techassist.net/forms/change.html